Shanghai Yiying Crane Machinery Co PA200 Electric Mini Hoist User Manual

Yiying Crane Machinery Co PA200 Electric Mini Hoist
User Manual

PA200 Electric Mini Hoist

ELECTRIC MINI HOIST USER MANUAL

Congratulations for your excellent choice our new electric tool is manufactured in compliance with the best and relibility standards,ensuring you efficiency and safety for a long period of time.

Specific
anon| Method of
use| Rated Vol(V)| Input Power (W)| Rated lifting weight (kg)| Lifting Speed (n/min)| Lifting
Height
(n)| Quan
/CNT
(PCS)| Packing
Dimension
(cm)| G.W/
N.W
(kg)
---|---|---|---|---|---|---|---|---|---
PA200| Single-hook| 110220| 480| 100| 10| 12| I| 381422| 11/12
Double-hook| 200| 5| 6
PA250| Single-hook| 110220| 510| 125| 10| 12| I| 381422| 11/12
Double-hook| 250| | 6
1’A300| Single-hook| 110220| §| 150| 10| 12| I| 381422| 11/12
Double-hook| 300| 5| 6
PA400| Single-hook| 110/220| 850| 200| 10| 12| 1| 441524| 15/16
Double-hook| 400| 5| 6
PA500| Single-hook| 110220| 1020| 250| 10| 12| 1| 441524| 15/16
Double-hook| 500| 5| 6
PA600| Single-hook| 110220| 1150| 300| 10| 12| I| 441524| 16/17
Double-hook| 600| | 6
PAS00| Single-hook| 110220| 1450| 400| 10| 12| I| 441524| 19/20
Double-hook| 800| 5| 6
PA 1000| Single-hook| 110220| 1800| 500| 10| 12| I| 592431| 30/31
Double-hook| 1000| 5| 6
PA 1200| Single-hook| 110/220| 2050| 600| 10| 12| I| 592431| 31/32
Double-hook| 1200| 5| 6

GENERAL SAFETY RULES

WARNING! Before using this electric tool. Carefully read the general safety rules listed below.

1. Your sockets must comply with safety rules. In case your sockets are not suitable, they should be checked by a skilled electrician.
2. Your socket plug must absolutely be grounded and your electric system must be supplied with a magneto cut-out safety.
   -When the machine is running unwatched, be careful that children cannot reach it.
   -Do not pull the electric cable to disconnect the plug.
   -The machine shall be protected from frost and low temperatures.
3. In case the machine cannot hoist a load, do not keep pressing the hoisting push button: this means that the load exceeds the machine’s maximum capacity.
   -The machine shall not be disassembled when running or connected to power.
   -Do not stand under hoisted weights.
4. Before starting the work, make sure that the steel cable is correctly winded around the reel and the pitch is equal to the cable diameter.
5. Observe the maximum load indicated on the hoist, not that no the hook!
6. Leave at least three turns of cable around the reel so that the cable connection is not under stress.
   -To avoid any danger, do not wind more than 15m of cable around the reel.
7. In case the steel cable is worn out, it must be replaced only with a cable of the same features manufactured by us. It can be found at all authorized service shops.
   -Before starting the word, check that switches are in good operating conditions.
8. In case the hoist stops during the lowering of a load, it is normal that the load goes down a few centimeters more because of inertia.
9. Attention! The hoist electric motor is not supplied with any overload cutout(to avoid an unexpected and unwanted restart) therefore, if you are unable to hoist a load do not insist and let the motor cool down.

MAINTENACE

-Periodically CHECK that the steel cable is in good condition.

1. CHECK that the screws securing the brackets and reduction gear are well tightened.
2. CHECK THE CONDITIONS AND TIGHTENING OF THE NUTS securing the steel cable clamps.
3. Periodically CHECK that the motor stop switch and push button switch are in good operating conditions.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>