GEORGE KOVACS P5386-613 Charming 6-Light Polished Nickel Cage Pendant Light Installation Guide

: October 30, 2023
: GEORGE KOVACS

Table of Contents

GEORGE KOVACS P5386-613 Charming 6-Light Polished Nickel Cage Pendant
Product Information
Product Usage Instructions
PREPARATION (Fig. 1)
Fig.3
Read User Manual Online (PDF format)
Download This Manual (PDF format)

GEORGE KOVACS P5386-613 Charming 6-Light Polished Nickel Cage Pendant

Light

GEORGE-KOVACS-P5386-613-Charming 6-Light-Polished-Nickel-Cage-Pendant-Light-
PRODUCT

Product Information

The product is a light fixture with item number P5386-613. It comes with a circular strap, ground screw, mounting screws, canopy with loop, quick link, loop, wire connectors, and candelabra base bulbs. It also includes several hardware bags with rods and glass covers. The fixture has a maximum wattage rating that should not be exceeded.

Product Usage Instructions

Shut off power at the fuse box or circuit breaker box and remove the old fixture including the mounting hardware.
Unpack the new fixture and lay out all the parts in a clean area, taking care not to misplace any small parts necessary for installation.
Slide cap (R) onto all thread (P) at the top of the cluster (Q).Secure rod (O) onto all threads on the cluster (Q). Secure fixture (S) on rod (O).
Slide cap (J) onto all thread (T) at the top of fixture (S). Secure rod (I) onto all thread (T) on top of fixture (S)
Determine the desired hanging height and thread rods (H1, H2, and H3) to all threads on rod (I). Then screw loop (G1) to rod (H1). Pass wires carefully through each rod as you assemble. Note: Remove all thread, if installing with one rod only.
Attach quick link (F) to loop (G1) and loop (G2) on canopy (C), carefully feeding wire through the loop (G1), quick link (F), and loop (G2).
Attach circular strap (A) to the junction box using mounting screws (B). The side of the circular strap (A) marked GND must face out.
Connect the electrical wires as shown in Fig.2, making sure that all wire connectors are secured. If your junction box has a ground wire (green or bare copper), connect the fixture’s ground wire to it. Otherwise, connect the fixture’s ground wire directly to the circular strap (A) using the ground screw provided.
Slide canopy (C) over circular strap (A) and secure with screws (D).
Install six candelabra base bulbs (K) up to 60 watts each or CFL or LED equivalent in accordance with the fixture specification-DO NOT EXCEED THE MAXIMUM WATTAGE RATING!
Alternate glass (L) and (N on hooks (Q), then hang hooks (M) to each glass (L) and (N). Alternate again glass (N) and (L) on hooks (M).
Return power to the junction box and test the fixture.

WAR N I N G ! S H U T P O WE R O F F AT F U S E O R C I R C U I T B R E AK E R . AVERTISSEMENT! COUPER LE COURANT AU NIVEAU DES FUSIBLES OU DU DISJONCTEUR.

PREPARATION (Fig. 1)

Shut off power at the fuse box or circuit breaker box and remove the old fixture including the mounting hardware.
Carefully unpack your new fixture and lay out all the parts in a clean area. Take care not to misplace any small parts necessary for installation.
Slide cap (R) onto all thread (P) at the top of the cluster (Q). Secure rod (O) onto all threads on the cluster (Q). Secure fixture (S) on rod (O).
ASSEMBLING THE FIXTURE (Fig.1)
Slide cap (J) onto all thread (T) at the top of fixture (S). Secure rod (I) onto all thread (T) on top of fixture (S).
Determine the desired hanging height and thread rods (H1, H2, and H3) to all threads on rod (I). Then screw loop (G1) to rod (H1). Pass wires carefully through each rod as you assemble. Note: Remove all thread, if installing with one 6” rod only.
Attach quick link (F) to loop (G1) and loop (G2) on canopy (C), carefully feeding wire through the loop (G1), quick link (F), and loop (G2).
Attach circular strap (A) to the junction box (not included) using mounting screws (B). The side of the circular strap (A) marked “GND” must face out
CONNECTING THE WIRES (Fig. 2)
Connect the electrical wires as shown in (Fig.2), making sure that all wire connectors are secured. If your junction box has a ground wire (green or bare copper), connect the fixture’s ground wire to it. Otherwise, connect the fixture’s ground wire directly to the circular strap (A) using the ground screw provided.
Tuck the wire connectors neatly into the junction box.
COMPLETING THE INSTALLATION (Fig. 1)
Slide canopy (C) over circular strap (A) and secure with screws (D).
Install (6) six candelabra base bulbs (K) up to 60 watts each or CFL or LED equivalent (not included) in accordance with the fixture specification-DO NOT EXCEED THE MAXIMUM WATTAGE RATING!
Alternate glass (L) and (N on hooks (Q), then hang hooks (M) to each glass (L) and (N). Alternate again glass (N) and (L) on hooks (M).

Your installation is now complete. Return power to the junction box and test the fixture. Note: The illustration (Fig. 1) in this manual is for installation purposes only. It may or may not be identical to the fixture purchased.