GEORGE KOVACS P5345-572-L 250-Watt Equivalence Integrated LED Polished Nickel and Coal Chandelier Instruction Manual
- October 30, 2023
- GEORGE KOVACS
Table of Contents
GEORGE KOVACS P5345-572-L 250-Watt Equivalence Integrated LED Polished
Nickel and Coal Chandelier
Product Information: INSTALLATION INSTRUCTIONS
Item#P5345-572-L (New. 2021/09/07)
READ AND SAVE THESE INSTRUCTIONS
WARNING ! SHUT POWER OF FAT FUSEOR CIRCUIT BREAKER .
MOUNTING THE FIXTURE (Fig.1)
-
Shut off the power at the circuit breaker and remove the old fixture, including the mounting hardware.
-
Carefully unpack your new fixture and lay out all the parts on a clean area. Take care not to lose any small parts necessary installation.
-
Place glass (L) and iron plate (K) over housing (T) and secure with screws (J).
-
Loosen screws (E) to remove mounting plate (A) from canopy (D).
-
Secure rod (G) onto all thread (H), then secure another rod (G) onto all thread on the previous rod (G).
-
Determine desired hanging height and thread rods (F1, F2 and F3) to all thread on rod (G). Attach canopy (D) by screwing onto rod (F1). Carefully pass the wires through each rod during assembly.
-
Attach mounting plate (A) to the junction box (not included) with mounting screws (B) (Size: #8-32N*L0.5). The side of mounting plate (A) with GND marked on it and two convex points must face out.
-
The support cable is provided to support the weight of the fixture while wiring. Align the fixture to mounting plate (A) and attach hook (I) on the end of support cable (C) into a slot located on mounting plate (A). Carefully allow support cable (C) to support the weight of the fixture while wiring (Fig.1).
CONNECTING THE WIRES (Fig. 2) -
Connect the electrical wires as shown in fig 2, making sure that all wire connectors are secured. If your junction box has a ground wire (green or bare copper), connect the fixture’s ground wire to it. Otherwise, connect the fixture’s ground wire directly to mounting plate (A) using the green screw provided.
-
Tuck wire connectors neatly into the junction box.
FINISHING THE INSTALLATION (Fig.1) -
Slide canopy (D) over mounting plate (A) and secure with screws (E).
-
Thread rod (R) onto all thread (S) on fixture body.
Replacing LED module (Fig. 3)
The LED module can be replaced by a qualified electrician without cutting
of wire and without damage to any decorative element to which the fixture is
attached. See installation steps for more details (Fig 3.)
- Shut off the power.
- Remove screws (E) and fixture body from mounting plate(A). Disconnect the wire connectors and place fixture body on a clean surface.
- Loose the screws (J). Remove the iron plate (K) and glass panel (L).
- Press the button of the printed L quick connector on LED module (O) with screwdriver (not included) to disconnected the black wire, and then disconnect the white wire from the printed K.
Product Usage Instructions
- Shut off the power at the circuit breaker before installing or replacing the fixture.
- Carefully unpack the new fixture and ensure all parts are present and accounted for.
- Mount the fixture according to the instructions provided, ensuring that all wiring is connected properly and securely.
- Test the fixture after installation to ensure it is functioning properly.
- To replace the LED module, shut off the power, remove the fixture body and disconnect wire connectors. Loosen screws and remove iron plate and glass panel. Press the button of the printed L quick connector on LED module with a screwdriver to disconnect the black wire, then disconnect the white wire from the printed K.
- Contact a qualified electrician if you are not comfortable with any aspect of installation or replacement.
INSTALLATION INSTRUCTIONS
Item#P5345-572-L (New. 2021/09/07) READ AND SAVE THESE INSTRUCTIONS
WARNING ! SHUT POWER OF FAT FUSEOR CIRCUIT BREAKER ..
MOUNTING THE FIXTURE (Fig.1)
-
Shut off the power at the circuit breaker and remove the old fixture, including the mounting hardware.
-
Carefully unpack your new fixture and lay out all the parts on a clean area. Take care not to lose any small parts necessary for installation.
-
Place glass (L) and iron plate (K) over housing (T) and secure with screws (J).
-
Loosen screws (E) to remove mounting plate (A) from canopy (D).
-
Secure rod (G) onto all thread (H), then secure another rod (G) onto all thread on the previous rod (G).
-
Determine desired hanging height and thread rods (F1, F2 and F3) to all thread on rod (G). Attach canopy (D) by screwing onto rod (F1). Carefully pass the wires through each rod during assembly.
-
Attach mounting plate (A) to the junction box (not included) with mounting screws (B) (Size: #8-32N*L0.5”). The side of mounting plate (A) with “GND” marked on it and two convex points must face out.
-
The support cable is provided to support the weight of the fixture while wiring. Align the fixture to mounting plate (A) and attach hook (I) on the end of support cable (C) into a slot located on mounting plate (A). Carefully allow support cable (C) to support the weight of the fixture while wiring (Fig.1).
CONNECTING THE WIRES (Fig. 2)
-
Connect the electrical wires as shown in fig 2, making sure that all wire connectors are secured. If your junction box has a ground wire (green or bare copper), connect the fixture’s ground wire to it. Otherwise, connect the fixture’s ground wire directly to mounting plate (A) using the green screw provided.
-
Tuck wire connectors neatly into the junction box.
FINISHING THE INSTALLATION (Fig.1) -
Slide canopy (D) over mounting plate (A) and secure with screws (E).
-
Thread rod (R) onto all thread (S) on fixture body.
Your installation is now complete. Return power and test the fixture.
Replacing LED module (Fig. 3)
Th e LED module can be replaced by a qualified electrician without cutting of wire and without damage to any decorative element to which the fixture is attached. See installation steps for more details (Fig 3.)
- Shut off the power.
- Remove screws (E) and fixture body from mounting plate(A). Disconnect the wire connectors and place fixture body on a clean surface.
- Loose the screws (J). Remove the iron plate (K) and glass panel (L).
- Press the button of the printed “L” quick connector on LED module (O) with screwdriver (not included) to disconnected the black wire, and then disconnect the white wire from the printed “N” quick connector on LED module (O).
- Remove screws (N). Carefully remove the LED module (O).
- Reverse steps b-e for installing the new LED module.
Note: For steps a-f are only used to replace the upper part of the LED module (O) of fixture. If the lower part of the LED module(Q) of the fixture needs to be replaced, please refer to the following steps:
- Shut off the power.
- Remove screws (E) and fixture body from mounting plate(A). Disconnect the wire connectors and place fixture body on a clean surface.
- Loose the screws (J). Remove the iron plate (K) and glass panel (L).
- Press the button of the printed “L” quick connector on LED module (O) with screwdriver (not included) to disconnected the black wire, and then disconnect the white wire from the printed “N” quick connector on LED module (O).
- Remove screws (N). Carefully remove the LED module (O).
- Loose the screws (M), then rotate holder (P) 90° on counter clockwise rotation, then take out the LED module (Q).
- Press the button of the printed “L” quick connector on LED module (Q) with screwdriver (not included) to disconnected the black wire, and then disconnect the white wire from the printed “N” quick connector on LED module (Q).
- Remove screws (N). Carefully remove the LED module (Q).
- Reverse steps b-h for installing the new LED module.
Dimmable with ELV and/or LED compatible wall dimmer switches.
Note: Illustration (Fig.1& Fig.3) on this manual is for installation
purposes only. It may or may not be identical to the fixture purchased.
IMPORTANT: FIXTURE SHOULD BE INSTALLED BY A QUALIFIED ELECTRICIAN TO ENSURE
PROPER WIRING AND INSTALLATION.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>