GEORGE KOVACS P1896-613 Missing Link 6-Light Polished Nickel Drum Pendant Light with Fine White Linen Shades Instruction Manual

KOVACS P1896-613 Missing Link 6-Light Polished
Nickel Drum Pendant Light with Fine White Linen Shades
Instruction Manual

INSTALLATION INSTRUCTIONS
Item#P1896-613 (Rev. 2021/05/25)
READ AND SAVE THESE INSTRUCTIONS

P1896-613 Missing Link 6-Light Polished Nickel Drum Pendant Light with

Fine White Linen Shades

WARNING ! SHUT POWER OF FATF USE OR CIRCUIT BREAKER .
AVERTISSEMENT! COUPER LE COURANT AU NIVEAU DES FUSIBLES OU DU DISJONCTEUR.

PREPARATION (Fig. 1)

1. Shut off power at the fuse box or circuit breaker box and remove the old fixture including the mounting hardware.

2. Carefully unpack your new fixture and lay out all the parts in a clean area. Take care not to misplace any small parts necessary for installation.
   ASSEMBLING THE FIXTURE WITH CHAIN LOOP (Fig.1 &Fig. 3)

3. Secure rod (J) onto all thread (I) on fixture body.

4. Determine the desired hanging height and thread rods (F1, F2 and F3) to the all thread on rod (J). Screw loop (H1) to rod (F1). Carefully feed wire through each rod as you assemble.

5. Attach quick link (G) to loop (H1) and loop (H2) on canopy (D). Carefully feed wire through loop (H1), quick link (G), and loop (H2).

6. Attach mounting plate (A) to the junction box (Not included) with mounting screws (B) (Size: #8-32N*L0.5”). The side of the mounting plate (A) marked “GND” and two convex points must face out.

7. The support cable is provided to support weight of fixture while wiring. Align the fixture to mounting plate (A) and attach hook (P) on the end of support cable (C) to a slot located on mounting plate (A). Carefully allow the support cable (C) to support  weight of the fixture while wiring.
   CONNECTING THE WIRES (Fig. 2)

8. Connect the electrical wires as shown in fig 2, making sure that all wire connectors are secured. If your junction box has a ground wire (green or bare copper), connect the fixture’s ground wire to it. Otherwise, connect the fixture’s ground wire directly to the mounting plate (A) using the green screw provided.

9. Tuck wire connectors neatly into the junction box.
   COMPLETING THE INSTALLATION (Fig. 1)

10. Place canopy (D) over mounting plate (A) and secure with screws (E)

11. Place candle covers (K) over sockets (L).

12. Install (6) six candelabra base bulbs (M) up to 60 watts each or CFL or LED equivalent (not included) in accordance with the fixture specification—DO NOT EXCEED THE MAXIMUM WATTAGE RATING! (NE PAS DEPASSER LA PUISSANCE NOMINALE MAXIMALE!).

Your installation is now complete. Return power to the junction box and test the fixture.
Note: Illustration (Fig. 1) on this manual is for installation purposes only. It may or may not be identical to the fixture purchased.
IMPORTANT: FIXTURE SHOULD BE INSTALLED BY A QUALIFIED ELECTRICIAN TO ENSURE PROPER WIRING AND INSTALLATION.

a. Hardware Bag:
A. Mounting Plate 1
B. Mounting Screw2
D. Canopy 1
E. Screw2
G. Quick Link1
H. Loop2

b. Hardware Bag:
F1. ROD 12″1
F2. ROD 12″2
F3. ROD 6″*1

LA-3380E

Documents / Resources

| GEORGE KOVACS P1896-613 Missing Link 6-Light Polished Nickel Drum Pendant Light with Fine White Linen Shades [pdf] Instruction Manual
P1896-613 Missing Link 6-Light Polished Nickel Drum Pendant Light with Fine White Linen Shades, P1896-613, Missing Link 6-Light Polished Nickel Drum Pendant Light with Fine White Linen Shades, Missing Link 6-Light Polished Nickel Drum Pendant Light, 6-Light Polished Nickel Drum Pendant Light, Polished Nickel Drum Pendant Light, Nickel Drum Pendant Light, Drum Pendant Light, Pendant Light
---|---

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>