GEORGE KOVACS P5435-697-L Island Light Ceiling Light Instruction Manual

GEORGE KOVACS P5435-697-L Island Light Ceiling Light

Product Information

The product being installed is item#P5435-697-L, a hanging fixture that is dimmable with ELV and/or LED-compatible wall dimmer switch. The fixture comes with a mounting plate, metal plate, canopy, swivels, and rods of different sizes. The installation requires shutting off power at the fuse or circuit breaker and connecting the fixture wires to the house wires. The fixture should be installed by a qualified electrician to ensure proper wiring and installation.

Product Usage Instructions

1. Remove the fixture carefully from the carton and check all parts as shown in the illustration.

2. Shut off power at the circuit breaker and remove the old fixture including the mounting hardware.

3. Attach the mounting plate (A) to the junction box using mounting screws (B) as shown in Fig. 1.
   Note : The side of mounting plate (A) marked GND must face out

4. Determine the desired hanging height and thread rods (F1, F2, and F3) to all threads on the fixture body. Carefully pass wires through each rod during assembly. Secure swivels (G) onto rods (F1).

5. Slide metal plate (E) and canopy (D) followed by lock washers (H) over swivels (G) and secure with hex nuts (I) via wrench (J) (not included).

6. Connect the driver output wire to the LED wires as listed below. Secure with wire connectors (I).

   • Red driver output wire (labeled Output+) to red LED wire (labeled LED+)
   • Yellow driver output wire (labeled Output-) to yellow LED wire (labeled LED-)

7. Connect the electrical wires as shown in Fig. 2, making sure that all wire connectors are secured. If your junction box has a ground wire (green or bare copper), connect the fixture ground wire to it. Otherwise, connect the fixture ground wire directly to the mounting plate (A) using the green screw provided. After the wires are connected, tuck them carefully inside the junction box.

8. Align canopy (D) over the mounting plate (A) and secure with screws (C).

9. Return power to the junction box and test the fixture.

Note : The illustration on the manual is for installation purposes only. It may or may not be identical to the purchased fixture.

INSTALLATION INSTRUCTIONS

Item# P5435-697-L (Rev. 04/26/2022)
READ AND SAVE THESE INSTRUCTIONS

PREPARATION

1. Carefully remove the fixture from the carton and check that all parts are included as shown in the illustration.

2. Shut off power at the circuit breaker and remove the old fixture including the mounting hardware.
   MOUNTING THE FIXTURE (Fig. 1)

3. Attach mounting plate (A) to the junction box (not included) using mounting screws (B) (Size: #8-32N*L1”L) as shown in Fig. 1. Note:
   The side of mounting plate (A) marked “GND” must face out.

4. Determine the desired hanging height and thread rods (F1, F2, and F3) to all threads on the fixture body. Carefully pass wires through each rod during assembly. Secure swivels (G) onto rods (F1).

5. Slide metal plate (E) and canopy (D) followed by lock washers (H) over swivels (G) and secure with hex nuts (I) via wrench (J) (not included).
   CONNECTION THE WIRES (Fig. 2)

6. There is one driver inside the canopy, connect the driver output wire to the LED wires as listed below. Secure with wire connectors (I).

7. Red driver output wire (labeled Output+) to red LED wire (labeled LED+)

8. Yellow driver output wire (labeled Output-) to yellow LED wire (labeled LED-)

9. Connect the electrical wires as shown in Fig. 2, making sure that all wire connectors are secured. If your junction box has a ground wire (green or bare copper), connect the fixture’s ground wire to it. Otherwise, connect the fixture ground wire directly to the mounting plate (A) using the green screw provided. After the wires are connected, tuck them carefully inside the junction box.
   FINISHING THE INSTALLATION (Fig. 1)

10. Align canopy (D) over a mounting plate (A) and secure with screws (C).

Your installation is now complete. Return power to the junction box and test the fixture.
Note : The illustration (Fig. 1) in this manual is for installation purposes only. It may or may not be identical to the fixture purchased.
Dimmable with ELV and/or LED compatible wall dimmer switch.

IMPORTANT : FIXTURE SHOULD BE INSTALLED BY A QUALIFIED ELECTRICIAN TO ENSURE PROPER WIRING AND INSTALLATION

Hardware Bag

• A. Mounting Plate*1

• D.Canopy*1

• E.Metal plate*1

• C.Mounting screw*2

• G.Swivel*2

• F1. ROD 6″*2

• F2. ROD 12″*4

• F3. ROD 12″*2

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>