George Kovacs P1675-084C-L Integrated LED Plated Pewter Instruction Manual

George Kovacs P1675-084C-L Integrated LED Plated Pewter

Product Information: P1675-084C-L LED Pendant

• The P1675-084C-L LED Pendant is a decorative lighting fixture that can be mounted to any ceiling junction box.
• The fixture comes with an acrylic shade (J), a cap (K), and a final (L) to secure the shade.
• The fixture has a stainless steel protective film that needs to be removed before installation.
• The LED module (M) can be replaced by a qualified electrician without cutting any wires or damaging the decorative elements.
• The fixture is dimmable with ELV and/or LED-compatible wall dimmer switches.

Product Usage Instructions

1. Before installation, make sure to read and save the instructions provided with the fixture.
2. Turn off the power at the circuit breaker or fuse before starting the installation process.
3. Attach the mounting plate (A-021-112) to the ceiling junction box using the green screw and two mounting screws (F1, F2).
4. Attach the rod (W30-1-084C*3) to the mounting plate using the provided screws.
5. Attach the fixture body to the rod using the provided hex nut (W).
6. Attach the cap (K) to the acrylic shade (J), and secure it with the finial (L).
7. Remove the stainless steel protective film from the fixture.
8. Attach the acrylic shade (J) to the fixture body using the provided hex nut (W).
9. Attach the glass panel (R) to the fixture body using the provided screws (S) and rubber washers (N).
10. Connect the wires from the fixture to the ceiling wiring, following standard electrical procedures.
11. Turn on the power at the circuit breaker or fuse.
12. Test the fixture to ensure it is working properly.
13. To replace the LED module (M), turn off the power at the circuit breaker or fuse before starting the process.
14. Remove screws (D) and wire connectors to remove the fixture body from the rod.
15. Loosen the finial (L), and remove cap (K). Loosen hex nut (W), and remove acrylic shade (J).
16. Loosen screws (S) and rubber washers (N), and remove the glass panel (R).
17. Disconnect the LED module (M) by loosening hex nuts (O), studs (P), screws (Q), and rubber washers (N). Press the button of the quick connector (T) on the LED module (M) with a screwdriver to disconnect the wire and carefully remove the LED module (M).
18. Install a new LED module (M) by reversing steps a – e for removing the old module.
19. Note: The LED module should be provided by a specified supplier.
20. The fixture should be installed by a qualified electrician to ensure proper wiring and installation.

WARNING! SHUT POWER OFF AT FUSE OR CIRCUIT BREAKER AVERTISSEMENT!COUPER LE COURANT AU NIVEAU DES FUSIBLES OU DO DISJONCTEU.

ASSEMBLING THE FIXTURE

1. Shut off power at the fuse box or circuit breaker box and remove the old fixture including the mounting hardware.

2. Carefully unpack your new fixture and lay out all the parts in a clear area. Take care not to misplace any small parts necessary for installation.

3. Attach mounting plate (A) to junction box (not included) using mounting screws (C) (Size: 8-32*1/2’’L). The side of mounting plate (A) marked “GND” must face out.

4. Thread all thread (I) to the hex joint of the fixture. Place decorative cover（H）to all thread (I) and secure with washer (G).

5. The fixture includes three 12″ and one 6″ rod. Determine desired hanging height and thread rods (F1, F2) to all thread (I). Feed the fixture wire carefully through each rod. If installing with one 6″ rod only all thread must be removed.

6. Secure rod (F) to swivel of the canopy (E).

7. The support cable is provided to support the weight of the fixture while wiring. Align the fixture to mounting plate (A) and attach hook (U) on the end of the support cable into a slot located on mounting plate (A). Carefully allow the support cable to support the weight of the fixture while wiring.
   CONNECTING THE WIRES (Fig.2)

8. Connect the electrical wires as shown in Fig.2, making sure that all wire connectors are secured. If your junction box has a ground wire (green or bare copper), connect the fixture’s ground wire to it. Otherwise, connect the fixture’s ground wire directly to the mounting plate (A) using the green screw (B) provided.

9. Tuck wire connectors neatly into the junction box.
   COMPLETING THE INSTALLATION

10. Align canopy (E) onto a mounting plate (A) and secure with screws (D).

11. Place cap (K) to acrylic shade (J), and secure with a finial (L).

12. Remove the stainless steel protective film on the fixture.

Your installation is now complete. Return power to the junction box and test the fixture.
CAUTION /ATTENTION: When handling fixtures, do not apply pressure to LEDs. Hold the fixture by the base only.

Replacing LED module

The LED module can be replaced by a qualified electrician without cutting wire and without damage to any decorative element to which the fixture is attached. See installation steps for more details (Fig.3,)

Warning: Turn off power at the circuit breaker before replacing the LED module.

• Shut off the power.
• Remove screws (D) and remove wire connectors and place the fixture body on a clean flat surface.
• Loosen the finial (L), and remove cap (K). Loosen hex nut (W), and remove acrylic shade (J）.
• Loosen screws (S) and rubber washers (N), and remove the glass panel (R).
• To disconnect the LED module: Loosen hex nuts (O), studs (P), screws (Q), and rubber washers (N). Press the button of quick connector (T) on the LED module (M) with a screwdriver to disconnect the wire and carefully remove the LED module (M.
• Reverse steps a – e for installing a new LED module (Fig.3).

Note: The LED module should be provided by a specified supplier.
IMPORTANT: The fixture should be installed by a qualified electrician to ensure proper wiring and installation.
Dimmable with ELV and/or LED-compatible wall dimmer switches.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>