GEORGE KOVACS P5381-613 Charming 1-Light Polished Nickel Cage Mini-Pendant Light Instruction Manual

GEORGE KOVACS P5381-613 Charming 1-Light Polished Nickel Cage Mini-

Pendant Light

Product Information:

The product is a lighting fixture with item number P5381-613, manufactured on May 13, 2022. The product comes with a circular strap, ground screw, mounting screws, rods, wire connectors, quick link, loop, canopy, and glass. The fixture can accommodate one medium base bulb up to 60 watts or CFL/LED equivalent. The product is designed for indoor use only.

Product Usage Instructions:

1. Shut off power at the fuse box or circuit breaker box and remove the old fixture including the mounting hardware.
2. Carefully unpack the new fixture and lay out all the parts in a clean area. Take care not to misplace any small parts necessary for installation.
3. Slide cap (J) onto all thread (P) at the top of fixture (O). Secure rod (I) onto all thread (P) on top of fixture (O).
4. Determine the desired hanging height and thread rods (H1, H2 and H3) to all thread on rod (I). Then screw loop (G1) to rod (H1). Pass wires carefully through each rod as you assemble. Note: Remove the all thread if installing with one 6 rod only.
5. Attach quick link (F) to loop (G1) and loop (G2) on canopy (C), carefully feeding wire through loop (G1), quick link (F), and loop (G2).
6. Attach circular strap (A) to the junction box using mounting screws (B). The side of the circular strap (A) marked GND must face out.
7. Connect the electrical wires as shown in Fig 2, making sure that all wire connectors are secured. If your junction box has a ground wire (green or bare copper), connect the fixture’s ground wire to it. Otherwise, connect the fixture’s ground wire directly to circular strap (A) using the green screw provided.
8. Tuck the wire connectors neatly into the junction box.
9. Slide canopy (C) over circular strap (A) and secure with screws (D).
10. Install one medium base bulb (K) up to 60 watts each or CFL or LED equivalent (not included) in accordance with the fixture specification–DO NOT EXCEED THE MAXIMUM WATTAGE RATING!
11. Alternate glass (L) and (N) on hooks (Q), then hang hooks (M) to each glass (L) and (N). Alternate again glass (N) and (L) on hooks (M).

READ AND SAVE THESE INSTRUCTIONS

WARNING! SHUT POWER OFF AT FUSE OR CIRCUIT BREAKER.

PREPARATION

(Fig. 1)

1. Shut off power at the fuse box or circuit breaker box an remove the old fixture including the mounting hardware.
2. Carefully unpack your new fixture and lay out all the parts in a clean area. Take care not to misplace any small parts necessary for installation.

ASSEMBLING THE FIXTURE (Fig.1)

3. Slide cap (J) onto all thread (P) at the top of fixture (O). Secure rod (I) onto all thread (P) on top of fixture (O).
4. Determine the desired hanging height and thread rods (H1, H2 and H3) to all thread on rod (I). Then screw loop (G1) to rod (H1). Pass wires carefully through each rod as you assemble. Note: Remove the all thread, if installing with one 6” rod only.
5. Attach quick link (F) to loop (G1) and loop (G2) on canopy (C), carefully feeding wire through loop (G1), quick link (F), and loop (G2)
6. Attach circular strap (A) to the junction box (not included) using mounting screws (B). The side of the circular strap (A) marked “GND” must face out

CONNECTING THE WIRES (Fig. 2)

7. Connect the electrical wires as shown in (fig 2), making sure that all wire connectors are secured. If your junction box has a ground wire (green or bare copper), connect the fixture’s ground wire to it. Otherwise, connect the fixture’s ground wire directly to circular strap (A) using the green screw provided.
8. Tuck the wire connectors neatly into the junction box.

COMPLETING THE INSTALLATION (Fig. 1)

9. Slide canopy (C) over circular strap (A) and secure with screws (D).
10.  Install (1) one medium base bulb (K) up to 60 watts each or CFL or LED equivalent (not included) in accordance with the fixture specification—DO NOT EXCEED THE MAXIMUM WATTAGE RATING! (NE PAS DEPASSER LA PUISSANCE NOMINALE MAXIMALE!)
11.  Alternate glass (L) and (N) on hooks (Q), then hang hooks (M) to each glass (L) and (N). Alternate again glass (N) and (L) on hooks (M).
    Note: Illustration (Fig. 1) on this manual is for installation purposes only. It may or may not be identical to the fixture purchased.

PRODUCT OVERVIEW

Fig.3

a. Hardware Bag:

• A. Circular Strap *1
• B. Screws *2
• C. Canopy with loop*1
• D. Mounting Screws*2
• E. Ground screw *1
• F. Quick Link*1
• G1. Loop*1
• R. Wire connectors *3

b. Hardware Bag:

• H1. ROD 12″*1
• H2. ROD 12″*1
• H3. ROD 12″*1
• I . ROD 6″*1

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>