GEORGE KOVACS P2265-084-L Brushed Nickel Double LED Pendant Lamp Instructions
- October 30, 2023
- GEORGE KOVACS
Table of Contents
GEORGE KOVACS P2265-084-L Brushed Nickel Double LED Pendant Lamp
Product Information
The P2265-084-L is a fixture that can be installed on a junction box. The fixture has a mounting plate (C), a ground screw (N), and two mounting screws (E). The fixture wires are black or smooth, white or ribbed, and bare copper (ground). The house wires are black (hot), white (neutral), and green (ground). The fixture is dimmable with ELV and/or LED compatible wall dimmer.
Product Usage Instructions
- Before installation, ensure that the power is turned off at the fuse or circuit breaker.
- Mount the fixture by aligning the canopy (J) to the mounting plate (C) and securing it with screws (G).
- Connect the electrical wires as shown in Fig. 2. Ensure that all wire connectors are secured.
- If the junction box (A) has a ground wire (green or bare copper), connect the fixture’s ground wire to it. Otherwise, connect the fixture’s ground wire directly to the mounting plate (C) using the green screw provided.
- Tuck the wires carefully into the junction box (A).
- After installation, turn on the power to the junction box and test the fixture.
- Important: The fixture should be installed by a qualified electrician to ensure proper wiring and installation.
- Caution: When handling the fixture, do not apply pressure to the LEDs. Hold the fixture by the base or fixture body only.
WARNING: SHUT POWER OFF AT FUSE OR CIRCUIT BREKER .
MOUNTING THE FIXTURE
-
Shut off power at the fuse box or circuit breaker box. If necessary, remove the existing fixture and its mounting hardware.
-
Carefully remove the new fixture from the carton and check that all parts are included as shown in the illustration.
-
Rotate frames (O,P) and ring (R,Q) to the desired positions.
-
Attach mounting plate (C) to junction box (A) (not included) using mounting screws (E) (Size: #8-32*1/2”L). The side of the mounting plate marked “GND” must face out.
-
Determine the desired hanging height and thread rods (K2 and K1) to all thread on top of fixture body (M). Attach canopy (J) by screwing onto rod (K1). Carefully pass the wires through each rod during assembly. Note: Remove all thread if installing with one 6” rod only.
-
There are two drivers inside the canopy, connect driver output wire to LED wire with wire nuts (F) as below:
- Red driver output wire (labeled 450mA Output+) to red LED wire (labeled 450mA LED+)
- Black driver output wire (labeled 450mA Output-) to black LED wire (labeled 450mA LED-)
- Red driver output wire (labeled 550mA Output+) to red LED wire (labeled 550mA LED+)
- Black driver output wire (labeled 550mA Output-) to black LED wire (labeled 550mA LED-)
-
The support cable is provided to support the weight of the fixture while wiring.
Align the fixture to mounting plate (C) and attach hook (D) on the end of support cable (H) into a slot located on mounting plate (C). Carefully allow the support cable (H) to support the weight of the fixture while wiring.
CONNECTION THE WIRES
-
Connect the electrical wires as shown in Fig. 2, making sure that all wire connectors are secured. If your junction box (A) has a ground wire (green or bare copper), connect the fixture’s ground wire to it. Otherwise, connect the fixture’s ground wire directly to the mounting plate (C) using the green screw provided. After the wires are connected, tuck them carefully into the junction box (A).
FINISHING THE INSTALLATION -
Align canopy (J) to mounting plate (C) and secure with screws (G).
Your installation is now complete. Return power to the junction box and test the fixture.
IMPORTANT: Fixture should be installed by a qualified electrician to
ensure proper wiring and installation.
CAUTION/ATTENTION: When handing the fixture, do not apply pressure to the
LEDs. Hold the fixture by the base or fixture body only.
Dimmable with ELV and/or LED compatible wall dimmer
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>