VIVO DESK-AC07U Curved Desk Corner Connector Instruction Manual
- October 30, 2023
- Vivo
Table of Contents
VIVO DESK-AC07U Curved Desk Corner Connector
Product Information
The Curved Desk Corner Connector is a product designed to connect two desks at
a corner angle. It comes with a Desk Sleeve (A), M6 Spacer (S-A), M5x35mm
Screw (S-B), M5x8mm Screw (S-C), M6x8mm Screw (S-D), and M5 Washer (S-E). It
also requires tools such as a Phillips Screwdriver, Tape Measure, Drill, and
Pencil for assembly.
It is important to note that this product contains small parts that may pose a
choking hazard and is not recommended for children under 3 years old. Adult
supervision is required during assembly.
Product Usage Instructions
- Place the Desk Sleeve (A) onto the desktop at the desired location. Measure the space between the underside of the desktop and the lower portion of the sleeve to determine the required Spacers (S-A) and Washers (S-E) for mounting. Remove Desk Sleev (A) from the desktop.
- Install your keyboard mount (not provided) to Desk Sleeve A using either M5x8mm Screws (S-C) or M6x8mm Screws (S-D), depending on the mount being installed. Tighten with a Phillips screwdriver.
- Attach Desk Sleeve (A) with the installed keyboard mount to the desktop. Use Desk Sleeve (A) and a pencil to mark drilling locations. Drill 10mm (.4) deep pilot holes in the desktop for Curved Desk Sleeve and the rear end of the keyboard mount using a 3mm (1/8) drill bit.
- Secure Desk Sleeve (A) and keyboard mount to the desk using M5x35mm Screws (S-B) with M6 Spacers (S-A), and M5 Washers (S-E) determined in Step One. Tighten with a Phillips screwdriver.
Note : The quantity of Spacers & Washers needed is determined by the gap of space between desktop and bottom of Sleeve. The use of one Spacer & Washer with each screw above is for visual aide ONLY.
If you encounter any issues during assembly or receive any damaged or
defective parts, contact the VIVO support team at help@vivo-
us.com or 309-278-5303 for immediate assistance.
SKU : DESK-AC07U
Scan the QR code with your mobile device or follow the link for helpful videos
and specifications related to this product. Instruction Manual
https://vivo-us.com/products/desk-ac07u
GET IN TOUCH
Monday-Friday from 7:00am-7:00pm CST
- help@vivo-us.com
- www.vivo-us.com
- 309-278-5303
Chat live with an agent!
WARNING!
If you do not understand these directions, or if you have any doubts about the safety of the installation, please call a qualified technician. Check carefully to make sure there are no missing or defective parts. Improper installation may cause damage or serious injury. Do not use this product for any purpose that is not explicitly specified in this manual and do not exceed weight capacity. We cannot be liable for damage or injury caused by improper mounting, incorrect assembly, or inappropriate use.
WARNING: CHOKING HAZARD
SMALL PARTS – NOT FOR CHILDREN UNDER 3 YEARS. ADULT SUPERVISION IS REQUIRED
PACKAGE CONTENTS
TOOLS NEEDED
NOTE : SOME HARDWARE MAY NOT BE USED
ASSEMBLY STEPS
- Place the Desk Sleeve (A) onto the desktop at the desired location. Measure the space between the underside of the desktop and the lower portion of the sleeve to determine the required Spacers (S-A) and Washers (S-E) for mounting. Remove Desk Sleev (A) from the desktop.
- Install your keyboard mount (not provided) to Desk Sleeve A using either M5x8mm Screws (S-C) or M6x8mm Screws (S-D), depending on the mount being installed. Tighten with a Phillips screwdriver.
- Attach Desk Sleeve (A) with the installed keyboard mount to the desktop. Use Desk Sleeve (A) and a pencil to mark drilling locations. Drill 10mm (.4) deep pilot holes in the desktop for Curved Desk Sleeve and the rear end of the keyboard mount using a 3mm (1/8) drill bit.
- Secure Desk Sleeve (A) and keyboard mount to the desk using M5x35mm Screws (S-B) with M6 Spacers (S-A), and M5 Washers (S-E) determined in Step One. Tighten with a Phillips screwdriver.
Note : The quantity of Spacers & Washers needed is determined by the gap of space between desktop and bottom of Sleeve. The use of one Spacer & Washer with each screw above is for visual aide ONLY.
Love your new VIVO setup and want to share? Tag us in your photo! @vivo_us
Open Monday – Friday 7:00am – 7:00pm CST,
our dedicated support team can offer immediate assistance with rapid response
times. If any parts are received damaged or defective, please contact us. We
are happy to replace parts to ensure you have a fully functioning product
-
309-278-5303 AVG. RESOLUTION TIME (within office hrs): 5M 4S
-
www.vivo-us.com AVG. RESOLUTION TIME (within office hrs): < 15 M
Chat live with an agent!
AVG. RESPONSE TIME (within office hrs): 1HR 8M
- 23% within < 15m
- 38% within < 30m
- 61% within < 1hr
- 83% within < 2hr
- 92% within < 3hr
FOR MORE VIVO PRODUCTS, CHECK OUT OUR WEBSITE AT: www.vivo-us.com
References
- Register a .US.COM domain today!
- VIVO - Desks, Monitor Mounting, and More Home & Office Solutions – VIVO - desk solutions, screen mounting, and more
- Curved Desk Corner Connector – VIVO - desk solutions, screen mounting, and more
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>