GE Pre-Lit Christmas Trees with Easy Light Technology Instruction Manual

GE Pre-Lit Christmas Trees with Easy Light Technology

Product Information:

The pre-lit Christmas tree eliminates cord connections and come with a tree stand, extension cord, and four tree sections. It is provided with an extension cord for a tree topper, which can be attached to the top section along the pole. The tree adapter can be plugged into the back of the tree top extension cord as an add-on. This feature allows you to use only one outlet. The tree is for indoor use only and requires a 120V power source.

Product Usage Instructions:

1. Carefully unpack the carton and remove bubble wrap. Inspect the sections of your tree. The carton should include sections labeled A, B, C, and Top, as well as a Tree Stand.

2. Insert section A into the tree stand and tighten the thumbscrew. Then insert the plug into an electrical wall outlet.

3. To assemble section B (or C), properly align and insert it into the top of section A (or B). Adjust branch tips, as needed, for a fuller look.

4. Repeat step 3 for all remaining tree sections labeled B, C, and Top.

5. To assemble the tree top, properly align and insert the Top section into the top of section C. Adjust branch tips, as needed,
   for a fuller look.

6. Gently press on foot pedal to select the desired lighting function.

7. If the tree does not illuminate, try stepping on the Color Change Foot Pedal and make sure the wall switch is turned on. If one section of your tree does not illuminate, check that section for loose or missing bulbs, all factory connections are properly made or that you properly made all the electrical connections between each tree section, ie, tree plug to extension cord outlet.

For tree storage, remove the tree’s main extension cord plug from the wall outlet. Starting at the top, disconnect the Top from section C and then disconnect section B (or C) from section A (or B). Gently fold the tips in branches and fold the branches up toward the center. Care should be taken to avoid damage to the lights. Remove section A from the tree stand.

Disclaimer: Do not use or install any additional Christmas lighting or ornamentation that is powered by a light bulb socket. Doing this may result in damage to your Christmas tree or cause personal injury. Doing this will result in a void of the limited warranty of this product. Disconnect the decorative item from the power source before performing any maintenance or cleaning.

If you have any problems with your tree, visit www.geholidaylighting.com for more information or call their toll free number at 1-877-398-7337. Check their website for latest service hours and assembly instruction videos.

Color Choice® LED Technology

Assembly Instructions

Nicolas Holiday Ltd. thanks you for purchasing this pre-lit Christmas
tree. Should you have any problems with your tree, visit us at
www.geholidaylighting.com for more information. You can call our
toll free number at 1-877-398-7337.
Check our website for latest service hours and assembly instruction videos.

TREE ASSEMBLY DIAGRAM

NOTE: No tools required

a.This tree is provided with an extension cord for a tree
topper, which can be attached to the top section
along the pole.
b. As an option, the tree adapter can be plugged into the
back of the tree top extension cord as an add-on.
This feature allows you to utilize only one outlet.

INSTALLATION

1. Carefully unpack the carton. Remove bubble wrap and inspect the sections of your tree. The carton should include sections labeled “A”, “B”, “C” and “Top”, as well as a Tree Stand.

2. The tree stand should be open and set at 90° angle.

3. Insert Section labeled A into tree stand, tighten the thumbscrew. Then insert the plug into an electrical wall outlet.

4. Untie RED twist-tie to release branch panels. All branches should fall into place with a gentle pull on the outer layer of branches.
   Fig. A. Start at the inner and stagger the tips. Move each tip up to 40°. Fig. B. Make tips 2 & 3 to horizontial, tip 4 to vertical and tips 5 and 6 up to 45°.

5. To assemble the section labeled “B” (or “C”), properly align and insert section “B” (or “C”) into the top of section “A” (or “B”). (See Fig. C) Adjust branch tips, as needed, for a fuller look.

6. Repeat “Step 4” for shaping.

7. To assemble the tree top, properly align and insert the “TOP” section into the top of section “C”. (See Fig. D) Adjust branch tips, as needed, for a fuller look.

8. Gently press on foot pedal to select the desired lighting function. (See below)

Troubleshooting Tips

• If the tree does not illuminate, try stepping on the Color Change Foot Pedal and make certain the wall switch is turned on. If one section of your tree does not illuminate, check that section for loose or missing bulbs, all factory connections are properly made or that you properly made all the electrical connections between each tree section, i.e., tree plug to extension cord outlet.
• DISCLAIMER : DO NOT USE OR INSTALL ANY ADDITIONAL CHRISTMAS LIGHTING OR ORNAMENTATION THAT IS POWERED BY A LIGHT BULB SOCKET. DOING THIS MAY RESULT IN DAMAGE TO YOUR CHRISTMAS TREE OR CAUSE PERSONAL INJURY. DOING THIS, WILL RESULT IN A VOID OF THE LIMITED WARRANTY OF THIS PRODUCT.
• Disconnect the decorative item from the power source before performing any maintenance or cleaning.
• For indoor use only 120V
• THIS IS NOT A TOY, FOR DECORATIVE USE ONLY.
• GE is a trademark of General Electric Company and is under license by Nicolas Holiday Ltd.
  ©2022 Nicolas Holiday Ltd.
  9 F., No. 37, Guangfu North Rd., Taipei, Taiwan 10560 All rights reserved.
  Printed in China 22044LO

Tree Storage

1. Remove the tree’s main extension cord plug from the wall outlet.

2. Starting at the top, disconnect the “TOP” from section “C” and then disconnect section “B” (or “C”) from section “A” (or “B”). {Fig. 1} Note: Gently fold the tips in branches and fold the branches
   up toward the center. {Fig. 2} Care should be taken to avoid damage to the lights.

3. Remove section “A” from the tree stand and close tree stand to place into the carton.

4. Refer to the drawing on how to repack your tree. {Fig. 3}

IMPORTANT: Store your carton neatly in a cool, dry location protected from sunlight to prolong the tree life and to better keep the light sets in working order. Do not place a heavy load on the carton to avoid damage to or crushing the carton and tree inside.

References

• The home for holiday lighting

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>