V I V O STAND-RACE1B Red, Black Racing Simulator Cockpit Instruction Manual

: October 30, 2023
: V I V O

Table of Contents

V I V O STAND-RACE1B Red, Black Racing Simulator Cockpit
Product Information
Product Usage Instructions
PACKAGE CONTENTS
ASSEMBLY STEPS
More Information
References
Read User Manual Online (PDF format)
Download This Manual (PDF format)

V I V O STAND-RACE1B Red, Black Racing Simulator Cockpit

Product Information

The Red / Black Racing Simulator Cockpit is a product for gamers who want to enhance their racing game experience. The cockpit is made up of a front support frame (A), two side support bars (B), a rear support bar (C), and various other components, such as a footrest (G) and a chair seat (K). The product comes with a warning for choking hazards and small parts not suitable for children under three years of age. The product has a weight capacity of 220 lbs (100kg).

Product Usage Instructions

Start by screwing the two foot pads (O) into the underside of the front support frame (A). Place a support bar spacer (D) onto the front end of each side support bar (B) and assemble them to the front support frame using M8x60 bolts. Insert the side support bars into the rear support bar (C) and secure them with x8 M8x16 bolts (S).
Remove the pre-installed bolts (A-1) from the front support frame (A). Assemble the right and left braces (E, F) to the frame using previously removed bolts and x4 M8x16 bolts (S).
Install the footrest (G) to the front support frame (A) using x2 M8x16 bolts (S) in the rear mounting holes. Insert X2 M8x16 screws (S) into the front holes in the footrest and front support frame to hold the footrest at one of three heights.
Attach the wheel mount (H) to the front support frame (A) using x2 M8x16 bolts (S). Adjust the wheel mount height and angle by removing the pre-installed bolts with washers from the sides, then reinstall while holding the mount at the desired height and angle.
Extend the slider on the right chair support with lock (I) by lifting on the lever and pulling forward. Extend the slider on the left chair support (J) by pulling forward. Install the chair supports to the chair seat (K) using spacers (P) and M8x30 bolts (T).
Mount the chair seat (K) with supports to the frame using x4 M8x16 bolts (S).
Assemble the chair back (L) to the brackets on the chair seat (K) using chair back bolts (Q). Install the left and right side covers (M, N) to the brackets using the side cover bolts (R).

For any questions or assistance, customers can contact VIVO customer support through email, phone, or live chat.

WARNING

If you do not understand these directions, or if you have any doubts about the safety of the installation, please call a qualified technician. Check carefully to make sure there are no missing or defective parts. Improper installation may cause damage or serious injury. Do not use this product for any purpose that is not explicitly specified in this manual. Do not exceed weight capacity. We cannot be liable for damage or injury caused by improper mounting, incorrect assembly or inappropriate use.

WARNING: CHOKING HAZARD

SMALL PARTS – NOT FOR CHILDREN UNDER 3 YEARS. ADULT SUPERVISION IS REQUIRED.

PACKAGE CONTENTS

NOTE: SOME HARDWARE MAY NOT BE USED.

TOOLS NEEDED

DO NOT EXCEED WEIGHT CAPACITY.
Failure to do so may result in serious injury.

ASSEMBLY STEPS

STEP 1

Screw x2 foot pads (O) into the underside of the front support frame (A). Place a support bar spacer (D) onto the front (angled) end of each side support bar (B), then assemble to the front support frame using M8x60 bolts. Tighten using the 5mm Allen wrench (C1). Insert the side support bars into the rear support bar (C), and secure using x8 M8x16 bolts (S) with the 5mm Allen wrench (C1). Screw x2 foot pads (O) into the rear support bar.

STEP 2

Remove pre-installed bolts (A-1) from the front support frame (A). Assemble right and left braces (E, F) to the frame using previously removed bolts and x4 M8x16 bolts (S). Tighten with the 5mm Allen wrench (C1).

STEP 3

Install the footrest (G) to the front support frame (A) using x2 M8x16 bolts (S) in the rear mounting holes.
Insert X2 M8x16 screws (S) into the front holes in the footrest and front support frame to hold the footrest at one of three heights. Tighten all bolts using the 5mm Allen wrench (C1).

STEP 4

Attach the wheel mount (H) to the front support frame (A) using x2 M8x16 bolts (S), and tighten with the 5mm Allen wrench (C1).
Adjust the wheel mount height and angle by removing the pre-installed bolts with washers from the sides, then reinstall while holding the mount at the desired height and angle.

STEP 5

Extend the slider on the right chair support with lock (I) by lifting on the lever and pulling forward. Extend the slider on the left chair support (J) by pulling forward.
Install the chair supports to the chair seat (K) using spacers (P) and M8x30 bolts (T). Tighten with the 5mm Allen wrench (C1).

STEP 6

Mount the chair seat (K) with supports to the frame using x4 M8x16 bolts (S) with the 5mm Allen wrench (C1).

STEP 7

Assemble the chair back (L) to the brackets on the chair seat (K) using chair back bolts (Q).
Install the left and right side covers (M, N) to the brackets using the side cover bolts (R), and tighten with a Phillips screwdriver.

STEP 8

OPTION A: Right Side Shift Lever

Attach the shifter mount (W) to the shifter support bar (V) using M6x15 bolts (X), making sure the long end faces back, and tighten with a Phillips screwdriver. Install the shifter support bar (V) to the right side of the frame using M8x50 bolts (Y) and nuts (Z). Tighten using the 5mm Allen wrench (C1) and wrench (D1). Adjust the mount angle by removing the pre-installed bolts from the sides, then reinstall while holding the mount at the desired angle.

OPTION B: Left Side Shift Lever

Attach the shifter mount (W) to the shifter support bar (V) using M6x15 bolts, making sure the long end faces back, and tighten with a Phillips screwdriver. Install the shifter support bar (V) to the left side of the frame using M8x50 bolts (Y) and nuts (Z). Tighten using the 5mm Allen wrench (C1) and wrench (D1). Adjust the mount angle by removing the pre-installed bolts from the sides, then reinstall while holding the mount at the desired angle.

STEP 9

Attach the cable clips (A1) to the frame for organizing cables.
Use the levers on the right side and underneath to adjust the seat angle and position.

More Information

Love your new VIVO setup and want to share?

Tag us in your photo! @vivo_us

Open Monday – Friday 7:00am – 7:00pm CST, our dedicated support team can offer immediate assistance with rapid response times. If any parts are received damaged or defective, please contact us. We are happy to replace parts to ensure you have a fully functioning product.

309-278-5303
- AVG. RESOLUTION TIME (within office hrs): 5M 4S
www.vivo-us.com
- Chat live with an agent!
- AVG. RESOLUTION TIME (within office hrs): < 15 M
help@vivo-us.com
- AVG. RESPONSE TIME (within office hrs): 1HR 8M
- 23% within < 15m
- 38% within < 30m
- 61% within < 1hr
- 83% within < 2hr
- 92% within < 3hr