V I V O DESK-AC07S Desk Corner Connector Instruction Manual

: October 30, 2023
: V I V O

Table of Contents

V I V O DESK-AC07S Desk Corner Connector
Product Usage Instructions
Product Assembly Steps
PACKAGE CONTENTS
ASSEMBLY STEPS
More Information
References
Read User Manual Online (PDF format)
Download This Manual (PDF format)

V I V O DESK-AC07S Desk Corner Connector

The Desk Corner Connector is a product designed to connect two desktops at a right angle, creating an L-shaped workspace. The product comes with a Desk Sleeve, M5x35mm Screws, M5x8mm Screws, M6x8mm Screws, Washers, and Spacers. The product can be installed in two ways: regular mounting and mounting with a keyboard tray.

Product Usage Instructions

Tools Needed

Phillips Screwdriver
Tape Measure
Drill

Product Assembly Steps

Option A: Regular Mounting

Place Desk Sleeve (A) on the desktop at the desired location.
Measure the space between the underside of the desktop and the lower portion of the sleeve to determine the required Spacers (S-E) and Washers (S-D) for mounting.
Drill 10mm deep pilot holes in the desktop for the desk sleeve and the rear end of the keyboard mount using a 3mm (1/8) drill bit.
Install using M5x35mm Screws (S-A) and previously counted Washers (S-D) and Spacers (S-E).

Option B: Mounting with Keyboard Tray

Place Desk Sleeve (A) on the desktop at the desired location.
Measure the space between the underside of the desktop and the lower portion of the sleeve to determine the required Spacers (S-E) and Washers (S-D) for mounting.
Remove Desk Sleeve (A) from the desktop.
Install front end of the keyboard mount (not provided) to Desk Sleeve (A) using either the M5x8 Screws (S-B) or M6x8 Screws (S-C), depending on the keyboard mount to be installed. Tighten with a Phillips screwdriver.
Fit Desk Sleeve (A) with keyboard mount to the desktop.
Drill 10mm deep pilot holes in the desktop for the desk sleeve and the rear end of the keyboard mount using a 3mm (1/8) drill bit.
Secure Desk Sleeve (A) and keyboard mount to the desk using M5x35 Screws (S-A) and previously counted Spacers (S-D) and Washers (S-E). Tighten with a Phillips screwdriver.

Note: The product contains small parts that can be a choking hazard for children under 3 years of age. Adult supervision is required during assembly. Some hardware may not be used during the installation process. For any questions or assistance, contact VIVO’s support team at help@vivo- us.com or through their website www.vivo- us.com.

WARNING

If you do not understand these directions, or if you have any doubts about the safety of the installation, please call a qualified technician. Check carefully to make sure there are no missing or defective parts. Improper installation may cause damage or serious injury. Do not use this product for any purpose that is not explicitly specified in this manual and do not exceed weight capacity. We cannot be liable for damage or injury caused by improper mounting, incorrect assembly, or inappropriate use.

WARNING: CHOKING HAZARD

SMALL PARTS – NOT FOR CHILDREN UNDER 3 YEARS. ADULT SUPERVISION IS REQUIRED.

PACKAGE CONTENTS

NOTE: SOME HARDWARE MAY NOT BE USED

TOOLS NEEDED

ASSEMBLY STEPS

OPTION A: Regular Mounting

Place Desk Sleeve (A) on the desktop at the desired location. Measure the space between the underside of the desktop and the lower portion of the sleeve to determine the required Spacers (S-E) and Washers (S-D) for mounting. Drill 10mm deep pilot holes in the desktop for the desk sleeve and the rear end of the keyboard mount using a 3mm (1/8”) drill bit. Install using M5x35mm Screws (S-A) and previously counted Washers (S-D) and Spacers (S-E).

OPTION B: Mounting with Keyboard Tray

Place Desk Sleeve (A) on the desktop at the desired location. Measure the space between the underside of the desktop and the lower portion of the sleeve to determine the required Spacers (S-E) and Washers (S-D) for mounting. Remove Desk Sleeve (A) from the desktop.
Install front end of the keyboard mount (not provided) to Desk Sleeve (A) using either the M5x8 Screws (S-B) or M6x8 Screws (S-C), depending on the keyboard mount to be installed. Tighten with a Phillips screwdriver.
Fit Desk Sleeve (A) with keyboard mount to the desktop. Drill 10mm deep pilot holes in the desktop for the desk sleeve and the rear end of the keyboard mount using a 3mm (1/8”) drill bit.
Secure Desk Sleeve (A) and keyboard mount to the desk using M5x35 Screws (S-A) and previously counted Spacers (S-D) and Washers (S-E). Tighten with a Phillips screwdriver.

More Information

Love your new VIVO setup and want to share?

Tag us in your photo! @vivo_us

Open Monday – Friday 7:00am – 7:00pm CST, our dedicated support team can offer immediate assistance with rapid response times. If any parts are received damaged or defective, please contact us. We are happy to replace parts to ensure you have a fully functioning product.

309-278-5303 AVG.
- RESOLUTION TIME (within office hrs): 5M 4S
www.vivo-us.com
- Chat live with an agent!
- AVG. RESOLUTION TIME (within office hrs): < 15 M
help@vivo-us.com
- AVG. RESPONSE TIME (within office hrs): 1HR 8M
- 23% within < 15m
- 38% within < 30m
- 61% within < 1hr
- 83% within < 2hr
- 92% within < 3hr