LUMEGEN PA 15672 GEN LED Linear Suspended Up and Down Light Instruction Manual

: June 15, 2024
: LUMEGEN

Table of Contents

LUMEGEN PA 15672 GEN LED Linear Suspended Up and Down Light
**Product Information
Specifications
Installation Instructions
GETTING STARTED
Electrical Connection
- Rope Suspension Installation
Linkable Instruction
FAQ’s
References
Read User Manual Online (PDF format)
Download This Manual (PDF format)

LUMEGEN PA 15672 GEN LED Linear Suspended Up and Down Light

**Product Information

**

The GEN/LED Linear Suspended Up and Down Light is a high-quality lighting fixture designed for both residential and commercial use. It provides efficient and adjustable lighting for various indoor spaces.

Specifications

Input Voltage: AC100-277V
Max Current Consumption of Driver to 0-10V dimmer: 2mA each

Installation Instructions

Rope Suspension Installation
To install the light using the rope suspension method, follow these steps:

Ensure that there is a pull-proof device to prevent electric shock.
Move the screws to the planned suspension position.
Connect L, N, GND, DIM+, and DIM- of the AC input wire to the respective terminals of the AC wire lead out from the junction box.
Couple the AC wire and steel wire rope together with a coupling clamp.
Connect the AC power and light up the lamp.

Linkable Instruction

Note : This instruction is only applicable to linkable products. To install the light using the linkable method, follow these steps:

Install Linear 1 to the ceiling as per the Suspension Installation instructions. Open the end cap.
Move out the AC wires and disconnect the A and B parts. Hand Screws H-shape plate Steel wire rope Electrical Connection
Insert the H-shape plate into the track.
Install Linear 2 to the ceiling. Open the end cap and connect B and C.
Push back the Power Supply Board to Linear 1 and insert the H-shape plate into Linear 2. Tighten the plate with 4 pcs hand screws.
Install the Linear Light using the above method, keeping one main input cord on one side for wiring and grounding.

Note : LED LINEAR CAN BE JOINTED TOGETHER AS NEEDED, BUT THE TOTAL NUMBER OF FIXTURES SHOULD BE NOT MORE THAN 7PCS (INCLUDING 7PCS). If you order to use an 18# cord, More Links can be Customized.

CCT Changeable
Note : This feature is only available for CCT changeable products. To change the CCT (Correlated Color Temperature) of the lithe ght, follow these steps:

Open the end cap on the side with AC wire.
Move the CCT Dip Switch to choose the desired CCT as indicated on the label.

FAQ

Can I use more than 7 fixtures together?

No, the total number of fixtures should not exceed 7, including 7 fixtures.

Can I customize more links if I use an 18# cord?

Yes, if you use an 18# cord, more links can be customized.

How do I change the CCT?

Open the end cap on the side with AC wire and move the CCT Dip Switch to choose the desired CCT.

Address : 1000 Westinghouse Drive STE 1, New Stanton PA 15672 Website: www.lightup.com

IMPORTANT

Please read the specification before installation, to make sure the service environment matches the condition in the specification.
Please confirm the applicable power supply before using
Make sure the switch of the product is off before connecting to the power supply to prevent electric shock.
Operation against rules may damage your property and even harm your safety.
Preliminarily estimate the required quantity of LED linear lights, then according to the power rating of a single linear light figure out the total power and design a power supply plan.
Dangerous high voltage, Non-professionals are not allowed to maintain the products.
If the exterior flexible cable or wire is damaged, it must be exchanged by the supplier, its agent, or other similar qualified personnel to avoid dangers.

GETTING STARTED

BOM

Electrical Connection

Remark : The max current consumption of our driver to 0-10V dimmer is 2mA for each one)

Rope Suspension Installation

Planning the installation distance, then drill 2 holes of $3.0mm in cement ceiling; drive the plug rubber into 2 round holes of 43.0mm with a hammer, and thread screw 8 through the fastening head 2 9; then fasten fixing head 2 into plastic rubber with a cross screwdriver;
Move the screws to the planned suspension position;
Rotate and fasten 2 fixing heads 3 and 2 screws of the left end; hold steel wire rope and lift lamp upward, then adjust balance screws to balance light, finally tighten balance screws;
Rotate and fasten 2 pieces of fastening head 1 Don the lamp and 2 pieces fastening head 20; then lead AC input wire out of junction box;
Connect L, N, GND, DIM+and DIM- of AC input wire to L, N, GND, DIM+and DIM- respectively of AC wire lead out from junction box; process anti-leakage treatment on wire joint of AC wire; couple AC wire and steel wire rope together with coupling clamp, then connect AC power and light up lamp.

Linkable Instruction

Note : Only available for Linkable Products.

Install Linear 1 to the ceiling as instructed in Suspension Installation. Open the end cap as the picture shows
Move out the AC wires, disconnect the A and B parts
Insert the H-shape plate into the track as the picture shows.
Install tinear 2 to the ceiling and open the end cap,c onnect B and C as the picture shows.
Push back Power Supply Board to tinear 1 then insert the H-shape plate to tinear 2, tand ighten the plate with 4 pcs hof and screws.
Install the Linear Light as the above method, and keep one main input cord on one side for wiring and grounding.
NOTE : LED LINEAR CAN BE JOINTED TOGETHER AS NEEDED BUT THE TOTAL NUMBER OF FIXTURES SHOULD BE NOT MORE THAN 7PCS (INCLUDING 7PCS) if you order to use 18# cord, More Links can be Customized.

CCT Changeable

Note : Only available for CCT changeable products.