V I V O MOUNT-PC01C Black Under Desk Leg Clamp PC Mount Instruction Manual

October 30, 2023
V I V O

V I V O MOUNT-PC01C Black Under Desk Leg Clamp PC Mount

Product Information

The Black Under Desk Leg Clamp PC Mount is a product designed to mount a PC tower under the desk, saving valuable desk space. It has a weight capacity of 22lbs (10kg) and comes with a clamp, mount, pads, screws, and an Allen wrench for assembly. The product has been tested for quality and safety and comes with a warning to not exceed the weight capacity to avoid serious injury.

Product Usage Instructions:

  1. Apply pads (C) to the top, bottom, and side of mount (B) as shown in Step 1 of the assembly instructions.
  2. Loosen the set screws on either side of mount (B) using the 4mm Allen wrench (T-A) to adjust the height as needed.
  3. Insert M5x6mm screws (S-A) into clamp (A), leaving a 2mm gap as shown in Step 3 of the assembly instructions.
  4. Insert the heads of M5x6mm screws (S-A) with clamp (A) into the slots in mount (B) as shown in Step 4 of the assembly instructions.
  5. Secure clamp (A) to mount (B) using M5x6mm screws (S-A) in the lower holes. Tighten all screws using a Phillips screwdriver as shown in Step 5 of the assembly instructions.
  6. Remove the protective film from clamp (A) and assemble it to the desk leg by tightening both knobs as shown in Step 6 of the assembly instructions.
  7. Loosen two screws on top of mount (B) and slide side support bracket out to maximum width as shown in Step 7 of the assembly instructions.
  8. Place the PC tower in mount (B), slide the bottom support up until mount (B) is fit vertically to the PC, and tighten set screws using the 4mm Allen wrench (T-A). Slide the side bracket into place to hold the PC, and tighten screws using a Phillips screwdriver as shown in Step 8 of the assembly instructions.
  9. The PC mount is now ready for use.

If you need any assistance with assembly or have any issues with the product, contact the dedicated support team at VIVO during their business hours of Monday – Friday from 7:00am-7:00pm CST. They can offer immediate assistance with rapid response times and are happy to replace parts to ensure you have a fully functioning product.

WARNING!
If you do not understand these directions, or if you have any doubts about the safety of the installation, please call a qualified technician. Check carefully to make sure there are no missing or defective parts. Improper installation may cause damage or serious injury. Do not use this product for any purpose that is not explicitly specified in this manual. Do not exceed weight capacity. We cannot be liable for damage or injury caused by improper mounting, incorrect assembly or inappropriate use.

WARNING: CHOKING HAZARD
SMALL PARTS : NOT FOR CHILDREN UNDER 3 YEARS. ADULT SUPERVISION IS REQUIRED.

PACKAGE CONTENTS

V-I-V-O-MOUNT-PC01C-Black-Under-Desk-Leg-Clamp-PC-
Mount-05

TOOLS NEEDED

  • DO NOT EXCEED WEIGHT CAPACITY.
  • Failure to do so may result in serious injury.

ASSEMBLY STEPS

STEP 1
Apply Pads (C) to top, bottom, and side of Mount (B) as shown.
V-I-V-O-MOUNT-PC01C-Black-Under-Desk-Leg-Clamp-PC-
Mount-09 STEP 2
Loosen the sets screws on the either side of Mount (B) using 4mm Allen Wrench (T-A) to adjust the height.
STEP 3
Insert M5x6mm Screws (S-A) into Clamp (A) leaving a 2mm gap.
V-I-V-O-MOUNT-PC01C-Black-Under-Desk-Leg-Clamp-PC-
Mount-11 STEP 4
Insert the heads of M5x6mm Screws (S-A) with Clamp (A) into the slots in Mount (B).
V-I-V-O-MOUNT-PC01C-Black-Under-Desk-Leg-Clamp-PC-
Mount-12 STEP 5
Secure Clamp (A) to Mount (B) using M5x6mm Screws (S-A) in the lower holes. Tighten all screws using a Phillips screwdriver.
V-I-V-O-MOUNT-PC01C-Black-Under-Desk-Leg-Clamp-PC-
Mount-13 STEP 6
Remove the protective film from Clamp (A) and assemble Clamp (A) to the desk leg by tightening both knobs.
V-I-V-O-MOUNT-PC01C-Black-Under-Desk-Leg-Clamp-PC-
Mount-14

STEP 7
Loosen two screws on top of Mount (B) and slide side support bracket out to maximum width
V-I-V-O-MOUNT-PC01C-Black-Under-Desk-Leg-Clamp-PC-
Mount-16 STEP 8
Place PC tower in Mount (B), slide bottom support up until Mount (B) is fit vertically to PC, and tighten set screws using 4mm Allen Wrench (T-A). Slide the side bracket into place to hold PC, and tighten screws using a Phillips screwdriver.
V-I-V-O-MOUNT-PC01C-Black-Under-Desk-Leg-Clamp-PC-
Mount-17 STEP 9
The PC mount is now ready for use.

Love your new VIVO setup and want to share?
Tag us in your photo! @vivo_us
LAST UPDATED : 05/24/2022 REV1.1
Open Monday – Friday 7:00am – 7:00pm CST,
our dedicated support team can offer immediate assistance with rapid response times. If any parts are received damaged or defective, please contact us. We are happy to replace parts to ensure you have a fully functioning product.

309-278-5303 AVG. RESOLUTION TIME (within office hrs): 5M 4S

www.vivo-us.com AVG. RESOLUTION TIME (within office hrs): < 15 M
Chat live with an agent!

help@vivo-us.com AVG. RESPONSE TIME (within office hrs): 1HR 8M

  • 23% within < 15m
  • 38% within < 30m
  • 61% within < 1hr
  • 83% within < 2hr
  • 92% within < 3hr

FOR MORE VIVO PRODUCTS, CHECK OUT OUR WEBSITE AT: www.vivo-us.com

Scan the QR code with your mobile device or follow the link for helpful videos and specifications related to this product.
Instruction Manual
https://vivo-us.com/products/mount-pc01c

References

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

V I V O User Manuals

Related Manuals