VIVO STAND-TV70A Dark Walnut Easel Studio TV Stand Instruction Manual
- October 30, 2023
- Vivo
Table of Contents
VIVO STAND-TV70A Dark Walnut Easel Studio TV Stand
Product Information
The Dark Walnut Easel Studio TV Stand is a versatile and stylish stand that can hold flat screen TVs up to 88lbs or 40kg. It come with a base, two poles, four legs, upper and lower VESA brackets,and various screws, washers, and spacers for assembly. The product also includes security cables and clips for added safety.
The stand is designed to be assembled with a Phillips screwdriver, drill, tape measure, level, and pencil. It should not be installed into drywall alone and must be mounted on wood studs or using the included hardware for brick and concrete walls.
It is important to note that the product has a weight capacity limit of 88lbs or 40kg, and failure to adhere to this limit may result in serious injury.
Product Usage Instructions
- Start by screwing the legs (C) into the base (A).
- Screw the poles (B) onto the top of the base.
- Loosen the support rings on the poles using the 4mm Allen wrench (H). Adjust rings to hold TV at desired height, using a tape measure to ensure the rings are adjusted evenly, and tighten with the 4mm Allen wrench (H). Note that the rings should be at least 2 inches below the tops of the poles.
- Remove screws from lower VESA bracket (E) and open clamps.
- If your TV has a flat back, position upper (D) and lower (E) VESA brackets horizontally on the back of the TV. Make sure that the upper bracket is on top and the lower bracket is below. Secure using screws (M-A or M-B) with square washers (M-F) and D5 washers (P-G), with security clips (P-B) installed to top holes. If your TV has a curved back, use screws (M-C, M-D, or M-E) with square washers (M-F) and spacers (M-G, M-H) with security clips (P-B) installed to top holes.
- Slide the TV with VESA brackets (D, E) onto poles. Close the clamps on the lower VESA bracket over the poles and secure with previously removed screws.
- Peel backing from cable clips (G) and install clips on rear legs. Use clips to organize cables. Optional: Secure cable clips using 3/8 screws (F). Screws are able to thread directly into wood without drilling pilot holes.
For further assistance or questions regarding installation,contact VIVO-US at help@vivo-us.com or call 309-278-5303.
Scan the QR code with your mobile device or follow the link for helpful videos
and specifications related to this product.
Instruction Manual
https://vivo-us.com/products/stand-tv70a
WARNING!
If you do not understand these directions, or if you have any doubts about the safety of the installation, please call a qualified technician. Check carefully to make sure there are no missing or defective parts. Improper installation may cause damage or serious injury. Do not use this product for any purpose that is not explicitly specified in this manual. Do not exceed weight capacity. We cannot be liable for damage or injury caused by improper mounting, incorrect assembly or inappropriate use.
TIPOVER WARNING
SERIOUS OR FATAL CRUSHING INJURIES CAN OCCUR FROM TIPOVER. TO HELP PREVENT TIPOVER:
- NEVER ALLOW CHILDREN TO CLIMB, STAND, HANG, OR PLAY ON ANY PART OF TV OR TV STAND.
- USE TIPOVER RESTRAINT OR ANCHOR STAND TO WALL
USE OF TIPOVER RESTRAINTS MAY ONLY REDUCE, BUT NOT ELIMINATE RISK OF TIPOVER.
PACKAGE CONTENTS
NOTE: SOME HARDWARE INCLUDED MAY NOT BE USED
WARNING: CHOKING HAZARD
SMALL PARTS – NOT FOR CHILDREN UNDER 3 YEARS. ADULT SUPERVISION IS REQUIRED.
DO NOT EXCEED WEIGHT CAPACITY.
Failure to do so may result in serious injury.
88lbs
(40kg)
TOOLS NEEDED
CAUTION!
DO NOT INSTALL INTO DRYWALL ALONE. VERIFY YOUR WALL CONSTRUCTION. USE WOOD
STUDS TO MOUNT. We include mounting hardware for brick and concrete walls. If
unsure, please contact us at vivo-us.com, email at help@vivo-
us.com, or call us at 309-278-5303.
ASSEMBLY STEPS
STEP 1
Screw the legs (C) into the base (A).
STEP 2
Screw the poles (B) onto the top of the base.
STEP 3
Loosen the support rings on the poles using the 4mm Allen wrench (H). Adjust
rings to hold TV at desired height, using a tape measure to ensure the rings
are adjusted evenly, and tighten with the 4mm Allen wrench (H).
NOTE: Rings should be at least 2” below the tops of the poles.
STEP 4
Remove screws from lower VESA bracket (E) and open clamps.
STEP 5
OPTION A: Flat Back Monitor
Position VESA brackets horizontally on the back of the TV, making sure upper
VESA bracket (D) is on top and lower VESA bracket (E) is below. Secure using
screws (M-A or M-B) with square washers (M-F) and D5 Washers (P-G), with
security clips (P-B) installed to top holes.
OPTION B: Curved Back Monitor Position VESA brackets horizontally on the back of the TV, making sure upper VESA bracket (D) is on top and lower VESA bracket (E) is below. Secure using screws (M-C, M-D or M-E) with square washers (M-F) and spacers (M-G, M-H) with security clips (P-B) installed to top holes.
STEP 6
Slide the TV with VESA brackets (D, E) onto poles. Close the clamps on
lower VESA bracket over the poles and secure with previously removed screws.
Peel backing from cable clips (G) and install clips on rear legs. Use clips to
organize cables.
Optional: Secure cable clips using 3/8” screws (F). Screws are able to thread directly into wood without drilling pilot holes.
STEP 7
OPTION A: Wood Stud Wall
Using Security Cable Clamps (P-C) as guides, mark drilling locations on wall
at the same height as the upper VESA bracket. Use of a stud finder is
recommended. Drill holes at least 1.6” (40mm) deep using a 1/8”
(3mm) drill bit. Mount clamps to wall using ST4.8×38 screws (P-E). Thread
security cable (P-A) through security clips on TV and center holes in cable
clamps as shown, then tighten clamps using the 2mm Allen wrench (P-D).
OPTION B: Concrete/Brick Wall Using Security Cable Clamps (P-C) as
guides, mark drilling locations on wall at the same height as
the upper VESA bracket, spaced 400mm – 650mm (16” – 26”) apart. Drill holes at
least 1.6” (40mm) deep using a 9/32” (7mm) drill bit. Insert concrete anchors
(P-F) into holes and mount clamps to wall using ST4.8×38 screws (P-E). Thread
security cable (P-A) through security clips on TV and center holes in cable
clamps as shown, then tighten clamps using the 2mm Allen wrench (P-D).
Love your new VIVO setup and want to share? Tag us in your photo! @vivo_us
LAST UPDATED: 09/02/2022 REV4.1
Open Monday – Friday 7:00am – 7:00pm CST,
our dedicated support team can offer immediate assistance with rapid response
times. If any parts are received damaged or defective, please contact us. We
are happy to replace parts to ensure you have a fully functioning product.
309-278-5303
AVG. RESOLUTION TIME (within office hrs): 5M 4S
www.vivo-us.com
Chat live with an agent!
AVG. RESOLUTION TIME (within office hrs): < 15 M
AVG. RESPONSE TIME (within office hrs): 1HR 8M
- 23% within < 15m
- 38% within < 30m
- 61% within < 1hr
- 83% within < 2hr
- 92% within < 3hr
FOR MORE VIVO PRODUCTS, CHECK OUT OUR WEBSITE AT: www.vivo-us.com
References
- Register a .US.COM domain today!
- VIVO - Desks, Monitor Mounting, and More Home & Office Solutions – VIVO - desk solutions, screen mounting, and more
- VIVO - Desks, Monitor Mounting, and More Home & Office Solutions – VIVO - desk solutions, screen mounting, and more
- Easel Stand for 49” to 70” TVs – VIVO - desk solutions, screen mounting, and more
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>