BK TECHNOLOGIES KAA0609 Test Cable Kit User Guide

October 30, 2023
BK TECHNOLOGIES

BK TECHNOLOGIES KAA0609 Test Cable Kit

Product Information

General
The KAA0609 is a cable assembly designed for testing KNG-M series radios. This cable is only compatible with HP8920. If you are using Aeroflex 3920, please use KAA0609A.

The Kit

  • Cable Assy
  • Double Banana Plug Adapter – 1 ea.
  • Speaker Load
  • BNC Male Binding Post – 2 ea.

Product Usage Instruction

Set-Up

  • Please refer to the diagram below for all the setup instructions.
  • Install the BNC Binding post then the Double Banana Plug adapter to the Audio In port 1 and 2 of HP8920.
  • Connect the brown Audio Output coax cable (labeled) to the Double Banana Plug Adapter.
  • Connect the other brown Mic audio coax cable to Audio Out port of HP8920.
  • Connect the DIN Connector Cable to MIC/ACC port of HP8920.
  1. Connect the RF Coax cable (N-Type) to the RF IN/OUT port of HP8920. Note: RF Cable is not supplied with this Kit.
  2. Connect the other end of the RF Coax cable (N-Type) to KNG-M antenna connector.
  3. Connect the dB25 connector assembly to the radio Accessory port at the back.
  4. On HP8920, in RX Test mode, place the cursor to AF ANL under To Screen box then press the cursor control knob. It should go to the next screen.
  5. Place the cursor to Audio In Lo then press the cursor control knob then choose Float.
  6. Go back to RX Test mode, the generator is now ready for use.

Note:
The KNG-M series radios have a floating ground audio output and should be connected as such.

Technical Service Support – Customer Service

BK Technologies
7100 Technology Drive Melbourne, FL 23904 (800) 422-6281 www.bktechnologies.com.

General

The KAA0609 is a cable assembly used for testing KNG-M series radios. This cable is compatible with HP8920 only. If using Aeroflex 3920, please use KAA0609A.

The Kit

BK-TECHNOLOGIES-KAA0609-Test-Cable-Kit-fig-1

Set-Up

  • Please refer to the diagram below for all the setup instructions.

  • Install the BNC Binding post then the Double Banana Plug adapter to the Audio In port 1 and 2 of HP8920.

  • Connect the brown Audio Output coax cable (labeled) to the Double Banana Plug Adapter.

  • Connect the other brown Mic audio coax cable to Audio Out port of HP8920.

  • Connect the DIN Connector Cable to MIC/ACC port of HP8920.BK-TECHNOLOGIES-KAA0609-Test-Cable-Kit-fig-2

  • Connect the RF Coax cable (N-Type) to the RF IN/OUT port of HP8920.
    Note: RF Cable is not supplied with this Kit.

  • Connect the other end of the RF Coax cable (N-Type) to KNG-M antenna connector.

  • Connect the dB25 connector assembly to the radio Accessory port at the back.

  • On HP8920, in RX Test mode, place the cursor to AF ANL under To Screen box then press the cursor control knob. It should go to the next screen.

  • Place the cursor to Audio In Lo then press the cursor control knob then choose Float.

  • Go back to RX Test mode, the generator is now ready for use.

NOTE: The KNG-M series radios have a floating ground audio output and should be connected as such.

Technical Service Support

Customer Service
BK Technologies 7100 Technology Drive
Melbourne, FL 23904
(800) 422-6281
www.bktechnologies.com.

References

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals