BK TECHNOLOGIES BKR 9000 Portable Digital Radio User Manual
- June 15, 2024
- BK TECHNOLOGIES
Table of Contents
- BK TECHNOLOGIES BKR 9000 Portable Digital Radio
- Product Information
- Battery Care and Maintenance
- Radio Controls
- Product Usage Instructions
- Messaging
- FAQ (Frequently Asked Questions)
- Introduction
- BK Technologies
- Operating Instructions
- 5,701,390, #5,649,050, #5,630,011, #5,581,656, #5,517,511, #5,491,772,
- 5,247,579, #5,226,084, and #5,195,166.
- ESC PREV NEXT ENT
- , $, +, -, =, ^, /, , |, <, >, {, }, [, ]
- References
- Read User Manual Online (PDF format)
- Download This Manual (PDF format)
BK TECHNOLOGIES BKR 9000 Portable Digital Radio
Product Information
Specifications
- Model: [Product Model]
- Dimensions: [Product Dimensions]
- Weight: [Product Weight]
- Frequency Range: [Frequency Range]
- Battery Type: [Battery Type]
- Antenna Type: [Antenna Type]
- Display: [Display Type]
Safety Precautions
Before using the product, please read and follow these safety precautions:
- Keep the product away from water and other liquids.
- Avoid exposing the product to extreme temperatures.
- Do not disassemble or attempt to repair the product yourself.
- Only use the specified battery and charger for charging.
- Keep the product out of reach of children.
Battery Installation and Removal
To install or remove the battery, follow these steps:
- Make sure the product is turned off.
- Locate the battery compartment on the back of the product.
- Slide the battery into the compartment, ensuring the contacts align properly.
- To remove the battery, push the release button and slide it out of the compartment.
Battery Care and Maintenance
To ensure optimal battery performance, follow these guidelines:
- Avoid exposing the battery to extreme temperatures.
- Regularly clean the battery contacts with a dry cloth.
- Do not attempt to charge non-rechargeable batteries.
- If the battery starts to leak or becomes damaged, replace it immediately.
Antenna Installation and Removal
To install or remove the antenna, follow these steps:
- Make sure the product is turned off.
- Locate the antenna connector on the top of the product.
- Screw the antenna clockwise onto the connector until it is securely attached.
- To remove the antenna, unscrew it counterclockwise from the connector.
Radio Controls
The product features various radio controls for operation:
- Main Display: Displays important information such as channel, signal strength, and battery level.
- Top Display: Provides additional information and status indicators.
- Programmable Switch and Button Functions: Can be customized to perform specific actions.
Product Usage Instructions
Basic Radio Operation
To use the radio, follow these steps:
- Turn on the product by pressing the power button.
- Select the desired channel or zone using the channel/zone selector knob or keypad entry.
- Adjust the volume using the volume control knob.
- To transmit, press and hold the push-to-talk (PTT) button while speaking into the microphone.
- To receive, release the PTT button and listen for incoming transmissions.
Trunking Channel Basic Operation
To operate in trunking channel mode, follow these steps:
- Enter the trunking channel mode by selecting the appropriate option in the menu.
- Use the channel/zone selector knob or keypad entry to navigate through available trunking channels.
- Follow the same transmit and receive steps as in basic radio operation.
Messaging
To send and receive messages, follow these steps:
- Access the messaging menu by pressing the corresponding button.
- Select the desired messaging option, such as text messaging or short message update.
- Enter the message content using the keypad or other input method.
- Send the message by pressing the send button or following the specific instructions for each messaging option.
FAQ (Frequently Asked Questions)
Q: How do I change the battery?
A: To change the battery, follow the instructions provided in the “Battery
Installation and Removal” section of the user manual.
Q: Can I use non-rechargeable batteries with this product?
A: No, only use the specified rechargeable battery for this product. Using
non-rechargeable batteries may cause damage to the product.
Q: How do I adjust the volume?
A: You can adjust the volume by using the volume control knob located on
the product.
Q: How do I send a text message?
A: To send a text message, access the messaging menu and select the text
messaging option. Enter the message content using the keypad and press the
send button.
BKR9000 Portable Radio User’s Manual
Introduction
Congratulations on your purchase of the BKR9000 Portable radio from BK
Technologies.
The BKR9000 APCO Project 25 radio offers an array of programmable
functionality to help radio users get the most out of their portable
communications. Check with your BK Technologies dealer or communications
officer for information on the programmed functions of your radio prior to
operation. This manual contains information concerning the operation
procedures for the BKR9000 Portable radio. The BKR9000 has been designed to
meet the tough requirements of today’s communications environment. Please take
a moment to read the information in this manual so you can get optimum
performance from your new radio.
FCC Requirements
Your radio must be properly licensed by the Federal Communications Commission
prior to use. Your BK Technologies dealer can assist you in meeting these
requirements. Your dealer will program each radio with your authorized
frequencies, signaling codes, etc., and will be there to meet your
communications needs as your system expands. The FCC rules require
manufacturers to comply with the FCC RF energy exposure limits for portable
2-way radios before they can be marketed in the U.S. When 2-way radios are
used as a consequence of employment, the FCC requires users to be fully aware
of and able to control their exposure to meet occupational requirements.
Exposure awareness can be facilitated by the use of a product label directing
users to specific user awareness information. Your BKR9000 2-way radio has a
RF exposure product label. Also, your BK5000 owner’s and service manuals
include information and operating instructions required to control your RF
exposure and to satisfy compliance requirements. This device complies with
part 15 of the FCC Rules. Operation is subject to the following two
conditions: (1) This device may not cause harmful interference, and (2) this
device must accept any interference received, including interference that may
cause undesired operation.
Any changes or modifications not expressly approved by BK Technologies could
void the user’s authority to operate this equipment.
– 1 –
BK Technologies
Note: This equipment has been tested and found to comply with the limits for a
Class B digital device, pursuant to part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses and can radiate radio
frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications. However,
there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and
on, the user is encouraged to try to correct the interference by one or more
of the following measures:
–Reorient or relocate the receiving antenna.
–Increase the separation between the equipment and receiver.
–Connect the equipment into an outlet on a circuit different from that to
which the receiver is connected.
–Consult the dealer or an experienced radio/TV technician for help.
Compliance with RF Exposure Standards
Your BKR9000 2-way radio is designed and tested to comply with a number of
national and international standards and guidelines (listed below) for human
exposure to radio frequency electromagnetic energy. This radio complies with
the IEEE and ICNIRP exposure limits for occupational/controlled RF exposure
environment at operating duty factors of up to 50% transmitting and is
authorized by the FCC for occupational use only. In terms of measuring RF
energy for compliance with the FCC exposure guidelines, your radio radiates
measurable RF energy only while it is transmitting (during talking), not when
it is receiving (listening) or in Standby Mode. Note: The approved batteries
supplied with this radio are rated for a 5-5-90 duty factor (5% talk – 5%
listen – 90% standby), even though this radio complies with the FCC
occupational RF exposure limits and may operate at duty factors of up to 50%
talk.
Your BKR9000 2-way radio complies with the following RF energy exposure
standards and guidelines:
United States Federal Communications Commission, Code of Federal Regulations;
47 CFR §§ 1.1307, 1.1310, 2.1091 and 2.1093
American National Standards Institute (ANSI) / Institute of Electrical and
Electronic Engineers (IEEE) C95. 1-1992
Institute of Electrical and Electronic Engineers (IEEE) C95.1-1999 Edition
– 2 –
BKR9000 Portable Radio User’s Manual
Innovation, Science and Economic Development Canada Compliance
This device complies with Industry Canada’s license-exempt RSSs. Operation is
subject to the following two conditions:
(1) This device may not cause interference; and
(2) This device must accept any interference, including interference that may
cause undesired operation of the device.
Le présent appareil est conforme aux CNR d’Industrie Canada applicables aux
appareils radio exempts de licence. L’exploitation est autorisée aux deux
conditions suivantes : (1) l’appareil ne doit pas produire de brouillage, et
(2) l’utilisateur de l’appareil doit accepter tout brouillage radioélectrique
subi, même si le brouillage est susceptible d’en compromettre le
fonctionnement.
WARNING:
Under Innovation, Science and Economic Development Canada regulations, this
radio transmitter may only operate using an antenna of a type and maximum (or
lesser) gain approved for the transmitter by Industry Canada. To reduce
potential radio interference to other users, the antenna type and its gain
should be so chosen that the equivalent isotropically radiated power
(e.i.r.p.) is not more than that necessary for successful communication.
- Conformément à la réglementation d’Industrie Canada, le présent émetteur radio
peut fonctionner avec une antenne d’un type et d’un gain maximal (ou
inférieur) approuvé pour l’émetteur par Industrie Canada. Dans le but de
réduire les risques de brouillage radioélectrique à l’intention des autres
utilisateurs, il faut choisir le type d’antenne et son gain de sorte que la
puissance isotrope rayonnée quivalente (p.i.r.e.) ne dépassepas l’intensité
nécessaire à l’établissement d’une communication satisfaisante.
The BKR9000 Radio Transmitter has been approved by Innovation, Science and Economic Development Canada to operate with the antenna types listed below with the maximum permissible gain and required antenna impedance for each antenna type indicated. Antenna types not included in this list, having a gain greater than the maximum gain indicated for that type, are strictly prohibited for use with this device.
Le présent émetteur radio (identifier le dispositif par son numéro de certification ou son numéro de modèle s’il fait partie du matériel de
– 3 –
BK Technologies catégorie I) a été approuvé par Industrie Canada pour
fonctionner avec les types d’antenne énumérés ci-dessous et ayant un gain
admissible maximal et l’impédance requise pour chaque type d’antenne. Les
types d’antenne non inclus dans cette liste, ou dont le gain est supérieur au
gain maximal indiqué, sont strictement interdits pour l’exploitation de
l’émetteur. Approved Antennas: Refer to www.bktechnologies.com for any updates
to the approved accessories.
Antenna BKR0893-148-E (All Band Antenna BKR0892-180 (Dual Band Antenna)
BKR0813 (50 cm VHF-GPS Whip Antenna)
Please refer to the following websites for more information on what RF energy
exposure is and how to control your exposure to assure compliance with
established RF exposure limits. http://www.ic.gc.ca/eic/site/smt-
gst.nsf/eng/sf01904.html http://www.ic.gc.ca/eic/site/ceb-
bhst.nsf/eng/h_tt00080.html
– 4 –
BKR9000 Portable Radio User’s Manual
Safety Precautions
· Do not operate the transmitter in close proximity to blasting caps.
· Do not operate the radio in an explosive atmosphere (petroleum fuels,
solvents, dust, etc.) unless your radio is an intrinsically safe model
designed for such use.
RF ENERGY EXPOSURE AWARENESS AND CONTROL INFORMATION, AND OPERATIONAL
INSTRUCTIONS FOR FCC OCCUPATIONAL USE REQUIREMENTS
BEFORE USING YOUR PORTABLE 2-WAY RADIO, READ THIS IMPORTANT RF ENERGY
AWARENESS AND CONTROL INFORMATION AND OPERATIONAL INSTRUCTIONS TO ENSURE
COMPLIANCE WITH THE FCC’S RF EXPOSURE
GUIDELINES.
NOTICE: This radio is intended for use in occupational/controlled conditions,
where users have full knowledge of their exposure and can exercise control
over their exposure to meet FCC limits. This radio device is NOT authorized
for general population, consumer, or any other use.
This 2-way radio uses electromagnetic energy in the radio frequency (RF)
spectrum to provide communications between two or more users over a distance.
It uses radio frequency (RF) energy or radio waves to send and receive calls.
RF energy is one form of electromagnetic energy; other forms include electric
power, radar, sunlight and x-rays. RF energy, however, should not be confused
with these other forms of electromagnetic energy, which when used improperly
can cause biological damage. Very high levels of x-rays, for example, can
damage tissues and genetic material. The energy levels associated with radio
waves from portable 2-way radios, when properly used, are not great enough to
cause biological damage.
Experts in science, engineering, medicine, health and industry work with
organizations to develop standards for exposure to RF energy. These standards
provide recommended levels of RF exposure for both workers and the general
public. These recommended RF exposure levels include substantial margins of
protection. All 2-way radios
– 5 –
BK Technologies
marketed in North America are designed, manufactured and tested to ensure they
meet government established RF exposure levels. In addition, manufacturers
also recommend specific operating instructions to users of 2-way radios.
These instructions are important because they inform users about RF energy
exposure and provide simple procedures on how to control it. Please refer to
the following websites for more information on what RF energy exposure is and
how to control your exposure to assure compliance with established RF exposure
limits.
http://www.fcc.gov/oet/rfsafety/rf-faqs.html
http://www.osha.gov/SLTC/radiofrequencyradiation/index.html
RF Exposure Compliance and Control Guidelines and Operation Instructions
To control your exposure and ensure compliance with the occupational/
controlled environment exposure limits always adhere to the following
procedures.
Guidelines: Do not remove the RF Exposure Label from the device.
User awareness instructions must accompany device when transferred to other
users. Do not use this device if the operational requirements described herein
are not met.
Operating Instructions
Transmit no more than the rated duty factor of 50% of the time. To transmit
(talk), push the Push-To-Talk (PTT) button. To receive calls, release the PTT
button. Transmitting 50% of the time, or less, is important because this radio
generates measurable RF energy exposure only when transmitting (in terms of
measuring for standards compliance).
Hold the radio in a vertical position in front of face with the microphone
(and the other parts of the radio, including the antenna) at least one inch
(2.5 cm) away from the nose. Keeping the radio at the proper distance is
important because RF exposures decrease with distance from the antenna.
Antenna should be kept away from eyes.
When worn on the body, always place the radio in a BK Technologies approved
clip, holder, holster, case, or body harness for this product. Using approved
body-worn accessories is important because the use of BK Technologies or other
manufacturer’s non-approved accessories may result in exposure levels which
exceed the FCC’s occupational/ controlled environment RF exposure limits.
– 6 –
BKR9000 Portable Radio User’s Manual
If you are not using a body-worn accessory and are not using the radio in the
intended use position in front of the face, then ensure the antenna and the
radio are kept at least one inch (2.5 cm) from the body when transmitting.
Keeping the radio at the proper distance is important because RF exposures
decrease with increasing distance from the antenna. Changes or modifications
to the radio and/or equipment that is not approved by BK Technologies could
void the user’s authority to operate the radio. Use only BK Technologies
approved supplied or replacement antennas, batteries, and accessories. Use of
non-BK Technologies approved antennas, batteries, and accessories may exceed
the FCC RF exposure guidelines. For a list of BK Technologies approved
accessories visit the following website: http://www.bktechnologies.com. The
AMBE® voice compression software included in this product is protected by
intellectual property rights including patent rights, copyrights and trade
secrets of Digital Voice Systems, Inc. The user of this software is explicitly
prohibited from attempting to decompile, reverse engineer, or disassemble the
object code, or in any other way convert the object code into a human-readable
form. This software is licensed solely for use within this product. US Patent
Nos. #6,912,495 B2, #5,870,405, #5,826,222, #5,754,974, #5,715,365,
5,701,390, #5,649,050, #5,630,011, #5,581,656, #5,517,511, #5,491,772,
5,247,579, #5,226,084, and #5,195,166.
Contact Information For additional information on exposure requirements or
other information, visit website http://www.bktechnologies.com.
– 7 –
BK Technologies
Information and Options
The BKR9000 is an All Band Land Mobile Radio. Up to 5000 channels can be
programmed into the radio. The channels may be divided into operating zones.
Zones can be designated as standard operating zones or command zones. Command
zones are made of up of channels selected from standard operating zones.
Band
VHF UHF 700 800
Operating Frequency 136 – 174MHz 380 – 520MHz 768 – 806MHz 806 – 869MHz
RF Power Output (Low-Hi) 1 – 6W 1 – 5W 1 – 3.0W 1 – 3.0W
Features
Factory installed options are listed on a label located on the speaker side of
your radio with the battery removed.
Features Encryption
OTAR Cloning
GPS Soft Power Down
P25 Trunking
Comments FIPS 140-3 Level 3 Support Encryption BKR, KNG2, Legacy Receives GPS
and GLONASS data
P25 FDMA, P25 TDMA, P25 ISSI Roaming
– 8 –
BKR9000 Portable Radio User’s Manual
Battery Installation and Removal
NOTE: For safety reasons, rechargeable battery packs are shipped uncharged or
only partially charged. Therefore, a rechargeable battery pack should be
properly charged in an approved battery charger before use. Only BK
Technologies approved batteries should be used to insure proper operation and
specifications.
Installing the Battery 1. Turn the volume knob to the off position. 2. Align
the battery with the radio as shown. 3. Push the battery upwards into the
radio
until release tabs “click” into place.
Removing the Battery 1. Push in the release tabs on
each side of the battery. 2. Pull the battery downwards
away from the radio.
NOTE: All information programmed into the radio is maintained even when the
battery pack is removed.
– 9 –
BK Technologies
Battery Care and Maintenance
BKR9000 battery packs are available in a variety of capacities and types for
special applications. Rechargeable battery packs can be charged separately or
while attached to a radio. Periodically check the contacts on the battery pack
for dirt or debris that could prevent a good electrical contact with the
charging base.
WARNING! DO NOT DROP A BATTERY
PACK INTO FIRE. AN EXPLOSION MAY OCCUR
Antenna Installation and Removal
NOTE: Transmitting without an antenna could result in damage to your radio.
Use BK Technologies approved antennas only. Use of non-qualified or mismatched
antennas could result in diminished radio operation. Published radio
specifications cannot be guaranteed with non-approved antennas. Bent, broken
or damaged antennas should be replaced.
Installing the Antenna
Insert the radio’s antenna connector into the threaded connector of the
antenna and turn it clockwise until it is firmly seated.
Removing the Antenna
Holding the base, turn the antenna counterclockwise until released.
– 10 –
Radio Controls
Channel/Zone Select Knob
Zone Collar Switch Antenna Connector
Accessory Connector
BKR9000 Portable Radio User’s Manual
On/Off Volume Knob
Microphone Main Display
Keypad
Encryption Collar Switch
Side Button 1 PTT (Push-to-Talk)
Side Button 2 Side Button 3
– 11 –
Emergency Button Top Display
Speaker Microphone
Battery
BK Technologies
Main Display
Status Indicators
Programmable Button Labels
RXA
H
BKR9000 AllBand 380.00000 Channel 1
CHAN ZONE SCAN MENU
Battery Level Indicator
Programmable Alphanumeric Labels
The BKR9000 main display can be programmed in RES (Radio Editor Software) for
a variety of options and functionality. Check with your BK
Technologies dealer or communications officer for information on the
programmed functions of your radio.
NOTE: The BKR9000 main display can be programmed to display different information when a trunking or conventional channel is selected.
Status Indicators
Receive Digital,
iP RXD, RXA Receive Analog, Hold
Time Active
TXD, TXA
Transmit Digital, Transmit Analog
L , H
Low or High transmit power
Trunking IP Data Enabled
Monitor Mode
Open Audio
C
Channel Scan On
Voice Mute Enabled
D
Dual Mode Scan On
GPS Enabled
Z P
Zone Scan On
C P
Priority Scan On
Repeater Talkaround Enabled
Selected channel is encrypted. Flashing means a reception is decrypted solid
means next TX will be encrypted.
– 12 –
BKR9000 Portable Radio User’s Manual
Alphanumeric Label Options NOTE: Three radio information lines are programmable with RES.
None
No information is displayed.
Channel Label Frequency*
Alphanumeric label of currently selected channel or active scanned channel.
Operating frequency of currently selected channel or active scanned channel.
Channel Number
Channel number of currently selected channel or active scanned channel.
Shows your P25 Unit ID
Unit ID
While receiving, the ID of the radio transmitting the message is displayed
If the received ID is programmed in your radio’s Call List, the corresponding label will be displayed
Rx’d TGID
P25 Talk Group ID of the radio transmitting the message currently being received.
Rx Picklist Selections*
NAC, TGID or Code Guard currently selected from the programmable RX Pick Lists.
Tx Picklist Selections*
NAC, TGID or Code Guard currently selected from the programmable TX Pick Lists.
Zone Label
Label of currently selected zone.
Zone and Channel # Currently selected zone and channel numbers.
Zone Number
Currently selected zone number.
Rx/Tx Key
Currently selected encryption key.
Rx Subaudible*
Displays CxCSS value of received signal.
Channel # and Zone Currently selected channel numbers and zone.
Radio Name
Displays radio name.
Site Affiliation Alias** Displays site afilliation alias.
Date & Time
Displays date and time.
GPS Peer Location
Displays the GPS location of a programmed peer.
*Conventional Channels Only **Trunking Channels Only
– 13 –
BK Technologies
Top Display
Status Indicators Programmable
C
H
A
N
0001
Alphanumeric Label
H
Battery Level Indicator
Status Indicators
The BKR9000 top display can be programmed in RES for a variety of options and
functionality. The orientation can also be changed in RES or by using the Top
Display Orientation menu item or Flip Top Display programmed button. The same
Alphanumeric Label Options that are available for the Main Display are
available for the Top Display. Note: One radio information line is
programmable with RES.
Programmable Switch and Button Functions
The BKR9000 portable radio is equipped with 10 programmable control buttons
and two programmable switches. Switch and button functions are assigned using
RES. NOTE: Switches, keypad, buttons and menu items can be programmed for
different functions when a trunking or conventional channel is selected.
Button Options and Labels All buttons except PTT are programmable with RES.
The programmed functions are activated by pressing the associated button.
Active functions are indicated by a highlighted background. SCN = Active, SCN
= Inactive.
Collar Switches
Emergency Button
D BC
Side Buttons
A
On
Off
Programmed Zone Programmable
Selector
Soft Keys/Buttons
– 14 –
BKR9000 Portable Radio User’s Manual
Keypad Menu Operation
A button can be programmed as “Menu”. Items shown in the Options and Labels
table can be programmed and arranged via PC programming. These items can then
be accessed with the Menu button.
ESC PREV NEXT ENT
To select from the menu: 1. Press the programmed “Menu” button. 2. Scroll to
the desired menu item with the
PREV and NEXT buttons. 3. Press the ENT button to open the item.
Options and Labels
Backlight Battery Life Call Alert Cancel Text Message Tone Change Status
Channel Add/Delete Channel Scan Channel Scan List Channel Select Cloning
Contrast Control Lock DMS List Edit Date and Time Dual Mode Scan Emergency
Enhanced Scan Evacuation Tones GPS* Hang Up Home Channel Inhibit
Menu Switch Button Label Trunk Conv.
x
x
x
LITE
x
x
x
x
LIFE
x
x
x
x
ALRT
x
x
x
CTMT
x
x
x
x
CSTS
x
x
x
CHAN+/- x
x
x
x
x
SCAN
x
x
x
SCN+
x
x
x
CHAN
x
x
x
x
CLON
x
x
x
CON
x
x
x
x
x
LCK
x
x
x
x
DSED
x
x
x
x
DATE
x
x
x
x
x
DSCN
x
x
x
–
x
x
x
x
x
ESCN
x
x
x
–
x
x
x
GPS
x
x
x
x
HANG
x
x
HOME
x
x
x
x
INH
x
– 15 –
BK Technologies
Options and Labels (cont.)
Menu Switch Button
Interconnect Call
x
x
Key Picklist**
x
x
Keypad Mute
x
x
x
Keyset Select
x
x
Menu
x
Message Update
x
x
Minimum Volume
x
x
Monitor
x
x
Nuisance Channel Delete
x
Phone
x
x
Power Down
x
Priority Channel Select
x
x
Priority Scan
x
x
x
Priority Scan List
x
x
Quick Status Update 1/2/3/4
x
RSM LED
x
x
x
RSM Speaker Attenuation x
x
x
Radio Accountability Tone
x
Radio Check
x
x
Radio Info
x
x
Rekey Request***
x
x
Send Alert Tone
x
Send Signal
x
Site Display****
x
x
Site Lock****
x
x
Site Search****
x
x
Squelch Adjust
x
x
Status Update
x
x
Surveillance Mode
x
x
x
System Test
x
x
Talkaround2 / Repeater Talkaround2
x
x
x
Talkback
x
Text Message
x
x
Label INTC KEY
KSET MENU MSG VOL MON DEL PHN PWRD PRI PSCN PSED
LEDS ATTN RAT RCHK
RKEY SNDT SEND STDS STLK STSR SQL
SURV STS
T/A
TKBK TXT
Trunk Conv.
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
– 16 –
BKR9000 Portable Radio User’s Manual
Options and Labels (cont.)
Menu Switch Button
Top Display Orientation / Flip Top Display
x
x
x
Two-Tone Select
x
x
Tx Digital
x
x
x
Tx Power
x
x
x
Tx Secure**
x
x
x
Uninhibit
x
x
Unit Call
x
x
User Rx NACs / Rx NAC Picklist
x
x
User Rx Tones / Rx CxCSS Picklist
x
x
User TGIDs / TGID Picklist x
x
User Tx NACs / Tx NAC Picklist
x
x
User Tx Tones / Tx CxCSS Picklist
x
x
Version
x
Voice Annunciation Mute
x
x
x
Voice Mute2
x
x
Vote Scan Zeroize Keys** Zone Scan Zone Scan List Zone Select
x
x
x
x
x
x
x
x
x
x
x
x
x
Label RTOP TONE TXAD PWR SEC UNINH UNIT RXNC
RXCG TGID TXNC
TXCG –
MUTE VSCN ZERO ZSCN ZSC+ ZONE
Trunk Conv.
x
x
x
x
x
x
x
x
x
x
x
x
x x x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
2Works on a per-channel basis. Requires GPS option. Requires Encryption option. Requires Encryption and OTAR options. ****Requires P25 Trunking option.
– 17 –
BK Technologies
Channel/Zone Selection Options
The BKR9000 can be programmed with up to 5000 individual channels. These
channels can be divided into zones of one or more channels. Accessing a
channel or zone depends on radio programming.
Channels or zones can be selected using the channel/zone select knob, by an
assigned button or menu item or by direct keypad entry. More than one
selection mode can be programmed.
Channel/Zone Selector Knob
When programmed with the default setting, the channel/zone knob is used to
select a channel (1-16) from the active zone. If programmed to select zones,
zones (1-16) will be selected with the knob.
The A/B/C/D switch is used to cycle through different programmed zones.
Channels or zones above sixteen can only be accessed via button, menu or
keypad selection. See below.
Button/Menu Item Selection
If programmed to a button, pressing the button will display the list of
available channels or zones. If programmed as a menu item, the lists can be
displayed by selecting Zone or Channel select from the menu list. (See “Keypad
Menu Operation”)
ESC PREV NEXT ENT
Use the PREV and NEXT buttons to scroll to the desired selection.
Alternatively, the number keys can be used to jump
directly to the desired channel or zone.
10
Press the button marked ENTER to go to the
highlighted zone or channel.
ESC PREV NEXT ENT
Direct Keypad Entry
The numeric keypad may also be programmed to directly select channels or
zones. Pressing a number will activate the zone or channel list.
10
ESC PREV NEXT ENT
Select the desired channel or zone and press the button marked ENTER or the
center navigation button to go to the highlighted location.
Press the button marked ESCAPE to cancel the selection and return to the
currently operating zone or channel.
– 18 –
BKR9000 Portable Radio User’s Manual
Using Knob and Button Operations Together
When selected via the button, menu or keypad method, the entered channel or
zone becomes active regardless of the knob position.
When the knob is turned, the radio leaves the keypad selected channel and goes
to the selection indicated by the knob position.
Example: With the channel select knob on channel 1, selecting channel 12 from
the keypad will switch the operating channel to channel 12.
Turning the channel knob to channel 2, switches the operating channel to
channel 2.
Basic Radio Operation
Turn power on by turning the Volume knob clockwise. A beep sounds, indicating
the radio is operational. The LCD display shows the programmed display
information of the currently selected channel.
RXD
H
BKR9000 AllBand 380.00000 Channel 1
Receive
Set the volume knob to approximately 50-60%.
When a signal is received, indicators on the left side of the display show the
signal strength and operating mode of the incoming transmission. RXA = analog,
RXD = digital.
To check radio volume when no signal is being received, put the Monitor mode
in “Open Squelch” (see “Monitor”) and adjust the volume to a comfortable
level.
CHAN ZONE SCAN MENU
Transmit
1. Press the PTT (Push-To-Talk) switch. When the radio is transmitting the
indicator LED glows red and TXD or TXA appears in the display.
2. Talk in a normal voice with the radio one to two inches from your mouth.
PTT
3. Release the PTT switch to stop transmitting.
TXD
H
BKR9000 AllBand 380.00000 Channel 1
CHAN ZONE SCAN MENU
If the length of your message is nearing the programmed Time-Out Timer setting, a tone sounds indicating 5 seconds left to transmit. At the end of the programmed time, the transmitter automatically shuts off and an alert tone sounds. To continue transmission, release the
– 19 –
BK Technologies
PTT switch, then press it again and continue talking.
If the Transmit Indicator does not glow and a tone sounds, you are on a
receive-only channel or the channel is busy (see Busy Channel Lockout). Select
an authorized transmit channel.
NOTE: When using a channel programmed for mixed mode transmit the signal will
be transmitted in the mode selected by the TX Digital selection. Or if
programmed for Mixed Mode Talkback, the radio will transmit in the mode of the
last received channel while the “RX” icon is
displayed. (See Mixed Mode Operation.)
Command Zone Operation
The BKR9000 portable radio allows construction of Command Zones drawn from any
of the programmed channels in standard operating zones. Each zone is
designated as a Standard Operating Zone or a Command Zone with RES.
Building a Command Zone [CHAN+] To build a Command Zone the “Channel
Add/Delete” function must be assigned to a programmable button.
While operating in a standard zone press the “CHAN+” button to add the
currently selected channel to a command zone. The list of available command
zones will be displayed. Use the up/down arrows to select the zone to add the
channel or use the number keys to move directly to the desired zone.
Pressing the “Enter” button copies the channel information to the first
available channel slot in the selected command zone.
Example: If the command zone has three channels, the newly added channel will
be channel four.
Editing a Command Zone [CHAN-] When operating in a Command Zone, press the
“CHAN-” button to remove the selected channel from the zone.
When a channel is deleted, the display momentarily shows “Channel Deleted”,
and the following channels move up in the list. For example, if channel 5 is
deleted, channel 6 becomes the new channel 5, channel 7 becomes the new
channel 6, etc.
NOTE: Modifications to a command zone channel, such as User Selected Tones, do
not affect the original standard zone channel. NOTE: Channels added by this
method cannot be cloned.
– 20 –
BKR9000 Portable Radio User’s Manual
Code Guard/NAC Operation
Conventional Channels
Code Guard Receive
Analog channels programmed with a receive code guard will be heard only when
the proper carrier frequency and Code Guard value is received. Analog and
mixed mode receive channels will also unmute when the radio is in monitor
mode. This is also true of digital channels. Monitor mode is carrier squelch
only.
Code Guard Transmit
Whenever transmitting on an analog channel, any programmed subaudible Code Guard is transmitted. Depending on radio programming, the Code Guard can be the default tone assigned to the channel or a tone selected from the Code Guard Picklist (see Pick List Options).
The frequency must be clear prior to transmitting on a Code Guarded channel. If the LED Indicator is green or blinking green do not transmit. Busy Channel Lockout can be programmed to disallow transmitting while a channel is busy.
Busy Channel/Transmit Indicator
1. Press the PTT switch. When the transmitter is on, the LED Indicator glows red and TX appears in the display.
2. Talk in a normal voice with the radio one to two inches from your mouth.
3. Release the PTT switch to stop transmitting.
Analog Squelch Control
Sub-audible signaling (CTCSS/CDCSS) is used to allow a group of radios to be
selectively called in an analog system. Programming the receive code guard
equal to zero allows for Carrier Squelch operation, where the radio will
unmute whenever a carrier is detected regardless of the transmitted Code
Guard.
– 21 –
BK Technologies
APCO Project 25 Digital Squelch Control
Network Access Codes (NACs) provide the digital equivalent of analog sub-
audible signaling (CTCSS/CDCSS) allowing a group of radios to be selectively
called within a system.
Users in the same area (using the same NAC) can be further divided into Talk
Groups, with each group having its own Talk Group ID (TGID). Group Calls are
made by designating both the users’ NAC and TGID.
Each radio also has an individual P25 unit ID. A Unit-to-Unit call contains
the addressee’s NAC, and uses the addressee’s P25 unit ID instead of the TGID.
When operating in Digital Mode, each channel can be programmed to use either
Normal squelch or Selective squelch.
Normal squelch is used to mimic analog operation. Signals are only qualified
with the programmed NAC. TGIDs and P25 Unit IDs are ignored. Each digital
channel is programmed with a receive NAC and a transmit NAC. When an incoming
signal’s NAC matches the channel’s programmed receive NAC, the radio unmutes.
The default NAC is 0659 ($293 hex).
The digital equivalent of carrier squelch is achieved by programming the
receive NAC = $F7E (3966 decimal). The radio will unmute when a digital signal
with any NAC is detected. The $F7E (3966 decimal) NAC is reserved for
receivers and is not allowed as a transmit NAC.
Selective squelch is used for processing Group Calls and Unit-toUnit Calls.
TGIDs are assigned on a per-channel basis. Users can be separated into Talk
Groups with each group having its own TGID. Then, on channels programmed for
Selective squelch, the incoming signal’s NAC and TGID must match the channels
programmed receive NAC and TGID for the radio to unmute. The default TGID is
- The TGID value 65535 ($FFFF hex) is used to effect an “All Call”. If the radio
receives a signal with a matching NAC and the TGID = 65535 ($FFFF hex), it
will unmute. Also, if the radio’s programmed TGID is 65535 ($FFFF hex), it
will open on any signal with a matching NAC, ignoring the incoming TGID. A
TGID = 0 means “no one”. If the radio is programmed with the TGID = 0, it will
accept incoming group calls containing the “All Call” TGID, and correctly
addressed Unit-to-Unit calls only.
– 22 –
BKR9000 Portable Radio User’s Manual
Mixed Mode Operation
The receiver and transmitter are capable of operating in analog wideband (25
kHz channel spacing), analog narrow-band (12.5 kHz channel spacing) and APCO
Project 25 Digital Mode.
Each channel’s Receive and Transmit Mode can be set independently as follows:
Mode Analog Digital
Mixed
RX
Receive qualified analog signals only
Receive qualified digital signals only
Automatically receive qualified analog or digital signals
TX Transmit analog signals only
Transmit digital signals only
Transmit analog or digital signal, depending on the status of “TX Digital”
switch
TXD
H
BKR9000 AllBand
TXA
H
BKR9000 AllBand
Digital receptions and transmissions will be indicated by illuminating the D
annunciator in addition to the RX or TX annunciator.
Analog receptions and transmissions will be indicated by illuminating the A
annunciator in addition to the RX or TX annunciator.
Mixed Mode Talkback If Mixed Mode Talkback is enabled, transmissions initiated while hold time remains will be in the same mode as the received signal, on the frequency of the Ready to Transmit (RTX) channel. Depending on radio state, the RTX channel can be the main channel, a held scan or priority channel if Talkback Scan is enabled, or the Priority 1 channel if “TX on PR1” is enabled. TX Mode on the RTX channel must be set to MIXED.
While hold time after a reception remains, transmissions will be in the
same mode as the received signal, regardless of
RXD
the status of the TX Digital switch. As in Talkback
H
Scan, the RTX channel and receive annunciators
will be displayed for the duration of the timer.
BKR9000 AllBand
Press the PTT while the RX indicator is shown
– 23 –
BK Technologies
Trunking Channel Basic Operation
Some BKR9000 radios are equipped with optional P25 Trunking capability. To
determine if your radio is trunking compatible, remove the battery and check
the Options Label. “BKR0579” indicates the trunking option is installed.
Trunking parameters and functions can only be programmed by qualified persons
via PC. Contact your system administrator or radio dealer for information on
how your radio is programmed.
System Registration If the radio is powered on when a trunking channel is
selected, the radio will attempt to register with the selected trunking
system. The LED will flash twice upon successfully registering with the system
and setting talkgroup affiliation. If the affiliation was unsuccessful the LED
will continue to flash. If the radio is not in range of the system “Out of
Range” will be displayed and an alert tone will sound every ten seconds. If
registration is refused or denied, a denied message and tone will appear
briefly before switching to “Out of Range” mode. After successful registration
the programmed LCD display criteria is displayed.
Transmitting When the PTT is pressed, if the channel is available a three beep
Talk Permit Tone will be heard and the radio will transmit. If there is no
channel available the radio will emit a tone and display “BUSY”. Release the
PTT. The radio will remain in busy mode until the channel is available. When
the channel becomes available the three beep Talk Permit Tone will be emitted.
Re-press the PTT to continue your call. If the PTT is not pressed within two
seconds of the Talk Permit Tone, the radio will return to normal standby mode.
– 24 –
BKR9000 Portable Radio User’s Manual
Scan Options
Channel Scan [SCAN] Conventional Channels When on, Channel Scan monitors
activity on the scan list channels in the currently operating zone. Scan
operates only while the radio is not transmitting. Channels designated as scan
channels are identified by the symbol at the top of the LCD display. If
allowed, the scan list can be edited by the radio user. (See Channel Scan
List). When Channel Scan is on, the C symbol will be shown at the top of the
LCD display. When a signal is detected, scanning stops and the message is
received. The received channel is shown in place of the selected channel. Once
the signal ends, the radio continues to monitor the channel for the preset
scan hold time before it resumes scanning. Channel Scan operation can be
assigned to a switch or as a button or a menu list item. Channel Scan may be
used in conjunction with Priority Scan operation (see Priority Scan).
Scanning Code Guarded Channels Conventional Analog Channels When a signal is
detected, scanning stops while the radio checks for the proper Code Guard
value. If the signal contains the proper Code Guard value, the radio receives
the message. Otherwise, the radio resumes scanning immediately.
Transmitting with Scan On The radio transmits on the channel selected by the
Channel Selector knob unless Talkback Scan is enabled, and PTT is pressed
within the radio’s scan hold time (see Talkback Scan) or Priority Scan is on
and Transmit on Priority 1 is enabled (see Priority Scan).
– 25 –
BK Technologies
Channel Scan List [SCN+] Conventional Channels
The Channel Scan List allows the radio user to add or remove channels from the
list of channels to be monitored while channel scanning.
Channels designated as scan channels are identified by the symbol at the top
of the LCD display.
The Scan List operation can be assigned as a button or menu list item.
To edit the Channel Scan list, select the channel you wish to add or remove
from the scan list. Press “+/-” to add or remove. Channels in the scan list
will be indicated with the symbol.
If Vote Scan option is installed, pressing the “+/-” button will cycle the
scan setting for the selected channel through checked (for scan on), “(V)” for
Vote Scan, and Off. When assigned as a menu item, open the menu and select the
channel you wish to add or remove from the scan list. Press “+/-” to add or
remove. Channels in the scan list will be indicated with the symbol.
Talkback Scan
Conventional and Trunking Channels
If your radio is programmed for Talkback Scan, any PTT transmission that
occurs while a channel is active or while scan hold time remains, will be on
the transmit frequency of the received channel. The `RX’ indicator will be
shown in the display while scan hold time remains.
Talkback Scan will not work if Priority Scan is on and your radio is also
programmed to transmit on the Priority 1 channel (see Priority Scan).
Vote Scan [Requires Option BKR0581] Conventional Channels
Channels in a multicast conventional systems can be added to the scan list and
designated as “voted” channels. When a signal is received on a voted channel
the radio checks all voted channels in the vote scan group and selects the
channel with the best signal.
If enabled, vote scanning takes place whenever the channel scan switch in on.
NOTE: Channel voting occurs only with Channel Scan and is disabled when Zone
Scanning. Channels programmed as Vote channels are treated as normal scan list
channels during Zone Scan operation.
Vote Scan groups can only be created in RES.
See also Priority Scan and Zone Scan.
– 26 –
BKR9000 Portable Radio User’s Manual
Dual Mode Scan [DSCN] Conventional and Trunking Channels
Dual Mode scan provides the ability to scan trunking and conventional channels
simultaneously.
NOTE: The Dual Mode Scan list must be setup using RES and cannot be changed by
the radio user.
When Dual Mode Scan is turned on the D icon is displayed and the radio scans
all channels in the dual mode scan list.
Dual Mode Scan can be assigned to a switch or as a button or menu list item.
For best operation, Dual Mode Scan should be assigned in both conventional and
trunking global settings with RES.
Enhanced Scan [ESCN] Conventional Channels
Enhanced Scan combines Priority Scan and Channel Scan to one switch/button.
Enabling Enhanced Scan will turn on both Priority and Channel Scan.
Priority Scan [PSCN] Conventional Channels
Two channels can be designated as priority channels. When Priority
Scan is on, these channels are monitored for incoming traffic. When a
qualified signal is detected the speaker is opened to listen to the message.
If a message is detected on the channel designated as Priority 2, the radio will continue to monitor Priority 1 channel for activity. If activity is detected the radio will switch to the Priority 1 channel.
When used in conjunction with Channel Scan, the radio monitors the Priority channels and will switch from a scanned channel to the Priority channel if a qualified signal is detected.
Depending on radio setup, priority channels can be tied to the currently
operating zone or can be assigned to a specific channel regardless of the
operating zone.
Channels designated as Priority channels are identified by the P1 or P2
symbol
at
the
top
of
the
LCD
display.
When
Priority
Scan
is
on,
the
C P
symbol will be shown.
Priority Scan operation can be assigned to a switch or as a button or a menu list item.
Trunked Channels
When on trunked channels, Priority Scan is used to turn system
scanning on or off.
– 27 –
BK Technologies
Priority Channel Select [PRI] Conventional Channels
Depending on programming, priority channels can be radio-wide (System) or zone
specific (Zone). Radio-wide priority channels are monitored regardless of the
current operating zone. (See Priority Scan for more details.)
If enabled the user can use the keypad to change the priority channels.
Priority Channel Select can be assigned to a switch or as a button or menu
list item.
Selecting a System Priority Channel Open the Priority Channel Select submenu
using the assigned control. Highlight a System Priority Channel type from the
list and press “ENTER”. The System Priority Channel submenu will appear.
Options: Off – Disables the priority channel. Use Main – Uses the selected
channel as the priority channel. Select – Assigns a specific channel as the
priority channel. To assign a specific channel as a System Priority Channel,
highlight “Select” and press the “ENTER” button.
The Zone selection menu will be displayed.
Highlight the zone of the desired priority channel and press the “ENTER”
button.
The Channel selection menu will then be displayed.
Highlight the desired channel and press the “ENTER” button to set the priority
channel.
The display will return to the main Priority Channel Select menu.
Selecting a Zone Priority Channel Open the Priority Channel Select submenu
using the assigned control. Highlight a Zone Priority Channel type from the
list and press “ENTER”. The Zone Priority Channel submenu will appear.
Options: Off – Disables the priority channel. Use Main – Uses the selected
channel as the priority channel. Select – Assigns a specific channel as the
priority channel. To assign a specific channel as a Zone Priority Channel,
highlight “Select” and press the “ENTER” button.
The Channel selection menu will be displayed.
– 28 –
BKR9000 Portable Radio User’s Manual
Highlight the desired channel and press the “ENTER” button to set the priority
channel. The display will return to the main Priority Channel Select menu.
Zone Scan [ZSCN] Conventional Channels
When Zone Scan and Channel Scan are on, the radio scans all programmed scan
channels in zones designated as Zone Scan zones.
If allowed, the scanned zone list can be edited by the radio user. (See Zone Scan List).
When
Zone
Scan
is
on,
the
Z P
symbol will be shown at the top of the
LCD display.
Zone Scan operation can be assigned to a switch or as a button or a menu list item and may be used in conjunction with Priority Scan operation.
Zone Scan List [ZSC+] Conventional Channels
The Zone Scan List allows the radio user to add or remove zones from the list
of zones to be scanned.
The Zone Scan List operation can be assigned as a button or menu list item.
When Zone Scan List is assigned to a button [ZSC+], press the button to add or
remove the currently operating zone from the scan list.
When assigned as a menu item, open the menu and select the Zone you wish to
add or remove from the scan list. Press “ENTER” to add or remove. Zones in the
scan list will be indicated with the symbol.
– 29 –
BK Technologies
Pick List Options
The BKR9000 provides users the ability to use Pick List options to program
specific channels. Pick List Options can be assigned to a programmed button or
as menu list items. Available Pick List options include:
Transmit Code Guards Receive Code Guards Transmit Network Access Codes Receive
Network Access Codes Talk Group IDs Encryption Keys (see Encryption Operation)
Encryption Keysets (see Encryption Operation)
TX/RX CxCSS Picklist [TXCG] [RXCG] Conventional Analog or Mixed Mode Channels
Selecting a CTCSS/CDCSS Code Guard from the Pick List will assign the tone to
the currently select analog or mixed-mode channel. User assigned Transmit and
Receive Code Guards are selected independently. To change a Code Guard, open
the RXCG or TXCG menu, select the desired tone and press “ENTER”. To return
the tone to the pre-programmed value select “Default”. If allowed, picklist
values can be changed through keypad programming.
TX/RX Network Access Code Picklist [TNAC] [RNAC] Conventional Digital or Mixed
Mode Channels Selecting a Network Access Code (NAC) from the Pick List will
assign the NAC to the currently select digital or mixed-mode channel. User
assigned Transmit and Receive NACs are selected independently. To change a
NAC, open the RXNAC or TXNAC menu, select the desired NAC and press “ENTER”.
To return the NAC to the pre-programmed value select “Default”. If allowed,
picklist values can be changed through keypad programming.
– 30 –
BKR9000 Portable Radio User’s Manual
Talk Group ID Picklist [TGID] Conventional Digital Channels Selecting a Talk
Group ID from the Pick List will assign the TGID to the currently select
channel. All other channels are unaffected. Open the menu of available TGIDs.
Select the desired Talk Group ID or, to return the TGID to the preprogrammed
value, select “Default”. Press “ENTER” to set the selection. If allowed,
picklist values can be changed through keypad programming.
Encryption Key Picklist [KEY] Digital or Mixed Mode Channels Encryption
equipped radios only. Selecting an Encryption Key from the Pick List will
assign the key to all encrypted channels that do not have `Key Lock’
programmed. Locked key channels will continue to use the pre-programmed key.
(See Encryption Operation)
Keyset Picklist [KSET] Digital or Mixed Mode Channels OTAR equipped radios
only. Selecting a Keyset from the Pick List will cause the radio to use
encryption keys from the selected Keyset. (See Encryption Operation)
– 31 –
BK Technologies
Unit-to-Unit Call Options
Individual Unit Call [UNIT] Conventional Digital and Trunking Channels P25
Unit IDs allow for Unit-To-Unit calls when the radio is operating in Digital
Mode. The function must be enabled by radio programming to allow this mode of
operation. Channels programmed for analog only operation will not be able to
transmit or receive Unit-To-Unit calls.
Conventional Channels Placing an Individual Unit Call Open the Unit Call menu
and select the desired “Unit Call” option.
Last Call = Use the P25 ID of the last Call. Call List = Use the programmed
P25 ID List. Enter ID = Enter a numeric P25 ID. Press Enter to enter Unit Call
Mode. The LCD displays the ID number or associate label of the targeted radio.
Press the PTT button to send the unit-to-unit call. To exit the Individual
Call mode press “Exit”. If there is no response to the call after 60 seconds,
the radio exits the Unit-to-Unit mode and returns to normal operation.
Receiving an Individual Unit Call When a properly addressed unit call is
received, an alert tone sounds and the LCD displays the ID number or
associated label of the radio placing the call.
Accept the call To accept the call and respond in unit-to-unit mode, press
“ACPT” and transmit as normal. To exit the Individual Call mode, press “Exit”.
Ignore the call To ignore the call and continue operating in normal mode,
press “IGNR”.
– 32 –
BKR9000 Portable Radio User’s Manual Unit-to Unit Callback If enabled,
pressing PTT during the hold time results in a Unit-to-Unit call to the
received unit ID. If there is no response to the call after 60 seconds, the
radio returns to normal operation. Call List Programming If enabled with RES,
the P25 Call List for conventional channels can edited via the radio’s keypad
programming function.
Trunking Channels
Limitations on unit-to-unit calls may programmed in trunking systems. Options
include disallowing unit-to-unit operation, limiting operation to only the
programmed unit call list or `response only’ which allows the user to respond
to incoming calls only. Check with your system administrator for information
about your programmed features. Placing a Call When placing a unit-to-unit
call on a trunking channel, a telephonetype ring tone will be emitted until
the targeted radio acknowledges or responds to the call.
Receiving an Individual Unit Call When receiving a unit call, an alert tone
will be emitted and the LCD will display the Unit ID of the radio sending the
call. Press “Accept” to respond to the call or “Ignore” to remain in normal
operation.
– 33 –
BK Technologies
Emergency Signaling Options
Conventional Digital and Trunking Channels
The BKR9000 portable radio supports P25 Emergency Operation. When Emergency
Operation is engaged the radio will transmit the P25 ID of the radio along
with the required P25 Emergency bit. Emergency operation applies only to
channels programmed for Digital or Mixed Mode transmissions.
On channels programmed for analog or Mixed Mode transmissions, and not
programmed for MDC Emergency Operation, the radio will not enter Emergency
Mode.
The radio will enter Emergency Mode when programmed for analog operation, if
it is also properly programmed with the correct MDC settings.
All scanning and priority functions will be disabled during Emergency
operation.
Depending on the radio’s PC programmable settings, emergency signal will be
sent automatically or with each Push-to-Talk.
Placing an Emergency Call
To place an emergency call, press and hold the programmed emergency button until the radio beeps and the display flashes “EMERGENCY”.
TXD
H
BKR9000 AllBand 380.00000 EMERGENCY
Radio automatically sends the emergency signal on the pre-programmed emergency
channel.
To return to normal operation press and hold the Emergency button or cycle
radio power.
CHAN ZONE SCAN MENU
Receiving an Emergency Signal
RXD
To receive an emergency call, the radio’s
H
receive mode must be programmed to Digital or
BKR9000 AllBand 380.00000 EMERGENCY
Mixed. When receiving a qualified emergency call, the
CHAN ZONE SCAN MENU
radio will beep. The display will flash the word “EMERGENCY” along with the P25 ID of the
radio sending the signal, for the duration of the reception, as well as
during any hold time. The RXD icon will also be lit.
– 34 –
BKR9000 Portable Radio User’s Manual
Encryption Operation
Conventional and Trunking Channels
The BKR9000 may optionally be configured for Secure communication on channels
operating in Analog or Digital Mode. To determine if your radio is encryption
compatible, remove the battery and check the Options Label near the top of the
radio. “BKR0574” indicates the encryption option is installed.
Required Setup
Radios that have the DES/AES factory option for encryption must have
encryption keys loaded with an APCO Project 25 compatible key fill device such
as the Motorola KVL 3000 Plus, using a BK Technologies keyloader cable. The
radio can hold up to 64 AES and/or DES keys.
After loading keys in the radio, RES must be used to configure the radio’s key
table and to assign default transmit keys to each channel.
Radios that have the OTAR factory option support Over-the-Air Rekeying of
encryption keys (OTAR). RES must be used to enable OTAR and to mark the
channel(s) that will communicate with the Key Management Facility (KMF). In
addition, the radio must have key encryption keys (used only to encrypt other
keys) loaded with an APCO Project 25 compatible key fill device such as the
Motorola KVL 3000 Plus, using a BK Technologies keyloader cable.
Basic Operation
The receiver automatically detects both clear and secure signals.
The transmitter selects clear or secure operation based on each channel’s programming. Digital channels can be programmed to always transmit encrypted, always transmit clear, or to select the encryption mode with the TX Secure switch.
The display indicates Secure Operation as follows:
In Standby Mode, if the radio will transmit in Secure Mode when PTT is
pressed, the encrypt icon is displayed.
RXD
H
When receiving an encrypted signal, the encrypt icon ‘ ‘ flashes in the display. When transmitting
BKR9000 AllBand 380.00000
an encrypted signal, the LED alternates between red and blue.
Channel 1
– 35 –
BK Technologies
Transmit Secure [SEC] Channels programmed for selectable encryption can have
“Transmit Secure” programmed as a switch, button or menu item. The default
setting uses the collar switch to select Transmit Secure. Ø = encrypted, O =
clear When SEC is on, encrypted channels programmed for switchable encryption
will transmit an encrypted signal. NOTE: The SEC switch has no effect on
channels programmed as Encrypted Only or Clear Only. Channels in the Ready-to-
Transmit Encrypted mode will display the symbol on the top line of the LCD.
Transmit Encryption Key Selection [KEY] The radio can hold up to 64 DES or AES
encryption keys. Each channel is assigned a default key for transmit. The key
can be locked to the channel, or if programming allows, a transmit key other
than the default key can be selected from the radio’s Key Pick List. To change
an encryption key, open the KEY menu. Programmed key labels will be displayed.
Select the desired key and press “ENTER”. To return the key to the pre-
programmed value select “Default”. If a key is selected that has not been
programmed, the radio will emit a three beep tone and display “Key Fail”
before going to standby mode. The radio will not transmit but will beep and
display “Key Fail” when PTT is pressed.
User Selectable Encryption Keyset [KEYST] OTAR equipped radios only. Selecting
a keyset from the Pick List will cause the radio to use encryption keys from
the selected keyset. User selectable menu access can be assigned to a button
or menu list item. To change the encryption keyset, open the KEYST menu.
Programmed Keyset labels will be displayed. Select the desired keyset and
press “ENTER”.
– 36 –
BKR9000 Portable Radio User’s Manual
Rekey Request [RKEY] OTAR equipped radios only.
On radios equipped with over-the-air rekeying (OTAR), a radio user can
manually request an encryption rekey from the Key Management Facility (KMF).
For a radio to receive encryption keys or keysets over-the-air, the selected
channel must be designated as an OTAR channel via PC programming. Refer to
your PC programming documentation for more information.
To request a re-key:
Open the Rekey Request menu.
Press the “YES” button to Request Keys, or press “ESC” to cancel the
operation.
If the “YES” button is pressed while on a channel that has not been marked as
an OTAR channel, the radio will beep and “NON-OTAR” will appear on the
display.
If a successful rekey occurs, a tone will sound, and the display will
momentarily show “REKEYED”.
Keyset Viewing and Selecting [KSET] OTAR equipped radios only.
The radio can hold up to 8 encryption keysets. Each keyset is limited to a
maximum of 64 keys. Only one keyset can be active at any time. The radio will
receive messages encrypted with any of the keys in any of the keysets, but
transmit keys can only be selected from the active keyset.
To change an encryption keyset, open the KEYST menu. Programmed keyset labels
will be displayed. Select the desired keyset and press “ENTER”.
Zeroizing [ZERO] The radio provides a method for the user to “panic-zeroize”
all encryption keys. Zeroizing removes all encryption keys from the radio,
including keys used for OTAR and Tactical OTAR operation.
Zeroize can be assigned as a button or menu list item. Open the “Zeroize Keys”
menu. Press “YES” to erase all encryption keys or “ESC” to cancel the action.
When successfully removed the “Keys Removed” message will momentarily be
displayed.
– 37 –
BK Technologies
Messaging
Digital Conventional P25 channels can be programmed to send and receive text
messages and radio status messages. Text messages can be selected from a pre-
programmed list or manually entered using the radio keypad. Status messages
are pre-programmed only.
Text Messaging [TXT] Conventional Digital Channels Text Messaging needs to be
configured in RES for both tx and rx radios. Message types include predefined
messages, manually entered messages or locally stored messages.
Predefined messages – Predefined messages are programmed into the radio memory
using RES. Manually Entered Messages – Text messages can be manually entered
via the radio’s keypad. Locally Stored Messages – Up to five manually entered
messages can be stored in individual radios.
Sending a Message To initiate a text message press the “TXT” button or select
“Text Message” from the menu. Select “Send” from the menu and press “ENTER”.
Select Message Type From the “Select Entry Type” menu, choose the type of
message to send and press “ENTER”.
Predefined List or Manual Entry List When “Predefined List” or “Manual Entry
List” is selected, a list of available messages is displayed. Select the
message to be sent and press “ENTER”. NOTE: When sending a predefined message
the message ID is transmitted. The receiving radio will display the message
programmed with the corresponding ID. If the receiving radio has no programmed
message with the transmitted ID, “Text Message X” is displayed, where “X” is
the received ID number.
– 38 –
BKR9000 Portable Radio User’s Manual
Manual Entry When “Manual Entry” is selected use the keypad to enter the
desired message (see keypad character table). Press “ENTER” to select the
target radio.
Select Target Radio Last Call – Select “Last Call” to send the message to same
radio you last sent a text message. Press “Send” to send the message.
Call List – Selecting “Call List” opens a list aliases for the preprogrammed
Unit IDs. Select the desired target radio and press “Send” to send the
message.
Unit ID – Select “Unit ID” to enter the P25 ID of the target radio. Use the
keypad to enter the ID then press “Send” to send the message
Broadcast – Select “Broadcast” to send the text message to all text enabled
radios regardless of unit ID. Press “Send” to send the message.
Message Acknowledgement When the text message has been received by the
targeted radio, an alert tone will sound and the acknowledgment message will
be displayed. Press “OK” or wait for five seconds to return to normal radio
operation. If the targeted radio is unavailable, an alert tone will sound and
the failed acknowledgement message will be displayed. Press “RTRY” to resend
the message. Press “OK” or wait for five seconds to return to normal radio
operation. When sending a “Broadcast” message, no “text received” notification
is shown. Only confirmation that the text has been broadcast will be
displayed.
Receiving a Message When an incoming text message is received an alert tone is
sounded and the Text Message Received message is momentarily displayed. The
top programmed display line will alternate between the programmed setting and
“Text Message” until the message is read.
– 39 –
BK Technologies
Reading the message To read the message press the “TXT” button or select `Text
Message” from the menu.
Select “Read” to view the message
Stored Messages Up to five messages can be programmed into the “Manual Entry
List” and are accessed from the “Select Entry Type” menu.
To store a manually entered text message press the “TXT” button or select
“Text Message” from the menu.
Select “Store” from the menu an press “Enter”.
Use the keypad to enter the desired message then press “Enter”. (See keypad
character table)
Select the storage slot for the message and press “Enter” to store the
message.
Short Message Update [MSG] Conventional Digital Channels
Short Message Update is a way for the radio to transmit an enumeration that
corresponds to a predefined message that is stored in other radios.
User Update Messaging [STS] Conventional and Trunking Digital Channels
Sending a Status Update NOTE: When sending a message the message ID is
transmitted. The receiving radio will display the message programmed with the
corresponding ID. If the receiving radio has no programmed message with the
transmitted ID “Status: Status X” is displayed, where “X” is the received ID
number.
Select Status Message Press the “STS” button or select “Status Update” from
the menu.
From the “Select Status” menu, select the programmed message to send and press
“Enter”.
Select Message Type From the “Select Target Type” select the type of message
to be sent.
Unit – Send the message to an individual radio ID. Group – Send message to a
group of radios using the Talk Group ID. Dispatch – Send the message to a
dispatch console.
– 40 –
BKR9000 Portable Radio User’s Manual
Unit Call Select Target Radio Last Call Select “Last Call” to send the message
to the same radio you last sent a status message. Press “Send” to send the
message.
Call List Selecting “Call List” opens a list aliases for the pre-programmed
Unit IDs. Select the desired target radio and press “Send” to send the
message.
Unit ID Select “Unit ID” to enter the P25 ID of the target radio. Use the
keypad to enter the ID then press “Send”.
Group Call Select Target Group ID Selecting “Group” opens the menu to send a
status message to a group of radios with matching talk group ID. Select
“Enter” to manually enter the ID or “Select” to choose and ID from the pre-
programmed talk group pick list.
Dispatch Select “Dispatch” to send a status message to a dispatch console.
Message Acknowledgement If the message has been received by the targeted
radio, an alert tone will sound and the acknowledgment message will be
displayed. If the targeted radio is unavailable, an alert tone will sound and
the failed acknowledgement message will be displayed. Press “OK” or wait for
five seconds to return to normal radio operation.
Receiving a Status Update When an incoming status update is received an alert
tone is sounded and the status message is momentarily displayed before
returning to normal operation.
– 41 –
BK Technologies
Paging and Call Alert
Conventional Two-Tone/DTMF/MDC1200 Paging [MUTE] Conventional Analog Channels
The BKR9000 can be programmed to receive two-tone, DTMF or MDC1200 pages on
conventional analog channels.
Receiving a page Select an analog or mixed-mode receive channel. Turn on
“Voice Mute” from the programmed button or menu item. When voice mute is
activated the icon is displayed. The radio ignores all voice traffic until the
proper tone sequence is received. When a proper signal is received the radio
will emit an alert tone and allow the audio to pass. If Auto Reset is
programmed, the radio will return to the muted standby mode when the time
conditions have been met.
Call Alert Paging [ALRT] Digital Channels The BKR9000 can be programmed to
send and receive Call Alert messages on digital channels. Sending a Call Alert
Press the “ALRT” button or open “Call Alert” from the menu. Select Target
Radio
Last Call Select “Last Call” to send the message to radio which you last sent
or received a call alert. Press “Enter” to send the message.
Call List Selecting “Call List” opens a list aliases for the pre-programmed
Unit IDs. Select the desired target radio and press “Enter” to send the Call
Alert.
Unit ID Select “Unit ID” to enter the ID of the target radio. Use the keypad
to enter the ID then press “Enter” to send the Call.
– 42 –
BKR9000 Portable Radio User’s Manual
Receiving a Call Alert When a Call Alert is received, an alert tone will sound
and the incoming unit ID or alias is displayed for approximately 5 seconds.
The top display line will alternate between the programmed display information
and a Call Alert Received message. Select “Call Alert” to reset.
Radio Check [RCHK] Conventional Digital Channels The BKR9000 can be programmed
to check the availability of a BKR9000 radio with a specific P25 ID.
Requesting a Radio Check Press the “RCHK” button or open “Radio Check” from
the menu. Select Target Radio
Last Call Select “Last Call” to send the request to the radio which you last
sent a radio check request. Press “Enter” to send the query.
Call List Selecting “Call List” opens a list aliases for the pre-programmed
Unit IDs. Select the desired target ID and press “Enter” to send the query.
Unit ID Select “Unit ID” to enter the P25 ID of the target radio. Use the
keypad to enter the ID then press “Enter” to send the query. If a successful
handshake is performed, an alert tone will sound and the “Unit Available”
message will be displayed for approximately five seconds. If no validation is
received from the targeted radio, an alert tone will sound and the “No
Response” message will be displayed for approximately five seconds.
– 43 –
BK Technologies
Radio Inhibit/Enable [INH]/[UNINH] Conventional Digital Channels With
“Inhibit” is assigned to a button or menu function, a BKR9000 Radio can
temporarily disable other BKR9000 radios using the targeted radio’s unit ID
number. The disabled radio can only be re-enabled by sending an “Unhibit”
command. NOTE: Inhibited radios cannot be read with RES.
Sending a command To initiate an inhibit/uninhibit message press the
programmed button or select from the menu. Use the keypad to enter the User or
Administrator password. Press “ENTER” to open the menu.
Select Target Radio Last Call Select “Last Call” to send the message to same
radio you last sent an inhibit or uninhbit message. Press “SEND” to send the
message.
Call List Selecting “Call List” opens a list aliases for the pre-programmed
Unit IDs. Select the desired target radio and press “SEND” to send the
message.
Unit ID Select “Unit ID” to enter the P25 ID of the target radio. Use the
keypad to enter the ID and press “SEND” to send the message.
Message Acknowledgement When the message has been received by the targeted
radio, an alert tone will sound and the acknowledgment message will be
displayed. Press “OK” or wait for three seconds to return to normal radio
operation. If the targeted radio is unavailable, an alert tone will sound and
the failed acknowledgement message will be displayed. Press “RTRY” to resend
the message. Press “OK” or wait for three seconds to return to normal radio
operation.
– 44 –
BKR9000 Portable Radio User’s Manual
Other Options and Functions
Many operational features and functions can be programmed for user selection
and control. Items can be programmed to the radio buttons or switches. In
addition to these quick set buttons, a menu of multiple functions can be
accessed with a “MENU” button.
Backlight [LITE] Conventional and Trunked Channels Backlight on/off control
can be assigned to a switch, button or as a menu item. In addition,
backlighting may be programmed with RES to illuminate when any key is pressed.
Battery Life [LIFE] Conventional and Trunked Channels Battery Life information
includes:
% battery capacity available until depletion The full capacity of the battery
Estimated time left before depletion
Busy Channel Operation
Conventional Channels The radio can be programmed for different behavior when
a conventional channel is busy. How the radio reacts to a busy channel is
programmed with the following operation options only accessible in RES:
Off – No busy channel transmit limiting will occur. Indicate – This setting
will display “Busy” momentarily and an alert tone will sound if conflicting
traffic is present, but the radio is still allowed to transmit. Lockout – This
setting prevents the radio from transmitting, “Busy” will be displayed and an
alert will sound until the PTT is released. Override – This setting prevents
the radio from transmitting. “Busy” will be displayed and an alert tone will
sound until the PTT is released. However a rapid release and press of the PTT
will allow the radio to transmit.
– 45 –
BK Technologies
Automatic – This setting will display “Busy” momentarily and an alert tone
will sound. The radio will then revert back to receive mode and monitor the
active receive traffic. (carrier mode only)
Busy Channel Conditions With RES, each channel is programmed for the
conditions under which the channel is considered busy. Conditions include:
Off – Channel is never declared busy. Carrier – A busy condition is declared
when carrier is present on the selected Rx frequency. Non-Qualified – A busy
condition is declared when a non-qualified signal is present on the Rx
frequency. (Non-qualified = Incorrect CTCSS/CDCSS, talk group or NAC ) Status
Symbol – Digital Channels Only. A busy condition is declared if the P25 busy
status symbol is present on the Rx frequency. Correct NAC – A busy condition
is declared when receiving digital signal with the correct NAC, and declared
not busy under all other conditions.
Channel Select [CHAN] Conventional and Trunked Channels Channel Selection can
be assigned to a button or menu item. (See Channel/Zone Selection Options for
details.)
Cloning [CLON] Conventional Zones BKR9000 radios can be set up to send or
receive programmed information from other BK Technologies products via a
cloning cable available from BK Technologies. Cloning can be assigned to a
button. Refer to the cloning cable manual for cloning information.
– 46 –
BKR9000 Portable Radio User’s Manual
Contrast [CON] Conventional and Trunking Channels Allows the user to adjust
the contrast of the screen. Select the desired contrast using the -/+ buttons.
Press “ENTER” to set the contrast.
Control Lockout [LCK] Conventional and Trunking Channels The BKR9000 portable
offers a variety of control lock options. Control lock can be assigned to a
collar switch or as a button or menu item. Switch Assignment When assigned to
the collar switch, toggling the switch on locks all controls except the collar
switch, PTT and volume/off.
Button/Menu Assignment When assigned as a button or menu item, users can
select from two lockout settings, “Lock Keypad Only” and “Lock All Controls”.
“Lock Keypad Only” locks only keypad button operations. “Lock All Controls”
locks all buttons and switches as determined by radio programming. Any or all
of the following function may be locked when “Lock All Controls” is selected:
keypad, side top buttons, channel knob, collar switch and push-to-talk. To
enable the lock function press the assigned button or open the menu and select
Control Lock from the list. Select the desired lockout setting and press
“ENTER” To disable Control Lock press the diamond button twice, then the
square button twice.
Date and Time [DATE] Conventional and Trunked Channels Displays the date and
time. The edit button allows the user to change the date and time. The time
will stay stored in the radio when powered off.
– 47 –
BK Technologies
DMS List Edit [DSED] Conventional and Trunking Channels DMS List Edit can be
assigned to a button or as a menu item. This will allow the user to view and
edit the DMS List.
Global Positioning [GPS] Conventional and Trunked Channels (Requires GPS
Option) To access GPS functions press the “GPS” button or select “GPS” from
the menu. Viewing GPS information To view current coordinates open the GPS
menu and select “GPS Information”. After acquisition, the current location is
displayed in degrees, minutes and seconds. Sending GPS information GPS
information is sent by a variety of triggers only accessible in RES:
PTT – After a digital transmission, the GPS coordinates will be automatically
transmitted. Periodic – GPS coordinates are transmitted periodically using a
programmed time. Emergency – GPS coordinates are sent if the radio activates
emergency. Power on/off – GPS coordinates are sent once the radio powers up
and acquires a position and also on power off. User Request – To send GPS
information, open the GPS menu and select “Transmit Request”. From the Request
menu select the desired target ID and press “Enter”.
Home [HOME] Conventional and Trunking Channels When pressed, the radio returns
to a preprogrammed channel that is configured in RES.
Keypad Mute
Conventional and Trunking Channels Keypad Mute on/off control can be assigned
to a switch, button or as a menu item. This will mute the keypad tones when
on.
– 48 –
BKR9000 Portable Radio User’s Manual
Keypad Programming
Conventional Systems and Channels
Much of the information stored in the BKR9000 can be edited using the keypad.
Five separate programming functions can be enabled with RES.
Keypad programming selections can only be assigned as a menu item.
Refer to the Keypad Programming section for detailed information on how to
edit programmed radio information.
Minimum Volume [VOL] Conventional and Trunking Channels
Must be configured as “Customizable” in RES to access through the radio. When
pressed, changes the volume level at lower volumes. This allows the user to
set their minimum volume to an audible level.
Monitor [MON] Conventional Channels
There are three settings available for monitoring traffic on a selected channel. “Monitor” can be assigned to a button or as a menu item.
Monitor Modes and Indicators
Off –
Squelch works as configured. (No indicator)
On –
Only carrier squelch is in effect. NAC and CxCSS and
TGID are all ignored. Steady on.
Open – No squelch is taking place. If there is no signal, the
audio will be static. Solid on.
Button Operation – A quick press will toggle between Off and On, while a long
press will turn on “Open” mode and short press will return the radio to Off
mode.
Menu Operation – Open the Monitor menu, select the desired operation and press
“Enter”.
Nuisance Channel Delete [DEL] Conventional Channels
If enabled, a nuisance channel can be temporarily removed from the scan list.
Nuisance Channel Delete can only be assigned to a button.
To temporarily remove a channel from the scan list, press the assigned button
while the nuisance channel is being received.
To revert to the programmed scan list, turn off Scan, cycle radio power or
select another zone or channel.
– 49 –
BK Technologies
Phone [PHN] and Hang Up [HANG] Conventional Channels The Phone function is a
way for a conventional radio to instruct the system to dial a phone number and
begin a call with that radio. Using the Hang Up button allows the user to end
that call.
Power Down [PWRD] Conventional and Trunking Channels When pressed, turns the
radio completely off.
Radio Accountability Tone [RAT] Conventional and Trunked Channels The Radio
Accountability Tone transmits a preprogrammed sequence of DTMF tones when the
RAT button is pressed and held. Must be programmed with a Radio Accountability
Tone ID in RES.
Radio info
Conventional and Trunking Channels Information about your radio can be viewed
via the “Radio Info” menu item. To review the information, open the Radio Info
menu. Use the NEXT or PREV to view individual items. Radio Info information
includes:
UID – P25 Unit ID. IP – IP Address of the radio. OTAR Registered –
Acknowledges if radio is registered to an OTAR system. Up Time – Amount of
time the radio has been on.
Repeater Talkaround [T/A] Conventional Channels In Repeater Talkaround mode,
the radio will transmit on the programmed receive frequency of the selected
channel. When T/A is enabled the icon will be displayed on the top line of the
LCD. NOTE: Channels programmed as receive only are not affected by the
Talkaround selection. Talkaround selection can be assigned to a switch, button
or as a menu list item.
– 50 –
BKR9000 Portable Radio User’s Manual
RSM LEDs [LEDS] Conventional and Trunking Channels RSM LED on/off control can
be assigned to a switch, button or as a menu item. This will turn the LEDs on
or off on the Radio Speaker Microphone.
RSM Speaker Attenuation [ATTN] Conventional and Trunking Channels RSM Speaker
Attenuation on/off control can be assigned to a switch, button or as a menu
item. This will toggle lower volume / higher volume on the Radio Speaker
Microphone.
Send Alert Tone [SNDT] Conventional and Trunking Channels When pressed and
held, the radio will transmit a 781.3Hz tone for the programmed duration.
Duration can be set in the range from 0.5 to 5 seconds.
Send Signal [SEND] Conventional Analog Channels Activated by a long-press and
is the 5-tone equivalent to emergency alarm. ANI Mode needs to be set to five-
tone. Holding this button will send the five-tone signal.
Squelch Adjust [SQL] Conventional Channels Squelch Adjust is used to change
the signal strength required for the radio’s speaker to unmute. Squelch can be
assigned as a button or menu list item. To adjust the squelch setting, open
the squelch menu. Select the desired threshold using the -/+ buttons. Press
“ENTER” to set the level.
Site Display [STDS] Trunking Channels When selected, the Site Display
functions shows information for the currently operating site. Displayed
information includes: Site ID, Site Alias and RSSI. Site Display can be
assigned as a button or menu list item.
– 51 –
BK Technologies
Site Lock [STLK] Trunking Channels Site lock prevents the radio from searching
for other sites by locking it to the currently selected site. Site Lock can be
assigned as a button or menu list item.
Site Search [STSR] Trunking Channels Site Search automatically searches and
selects the best available trunking site. Site Lock can be assigned as a
button or menu list item.
Surveillance Mode [SURV] Conventional and Trunking Channels When Surveillance
Mode is on, all audible indicators (beeps etc.) and lighting functions (LEDs
and Display) are disabled. Surveillance Mode can a switch, button or as a menu
list item.
System Test
Conventional and Trunking Channels The BKR9000 portable offers a variety of
system tests when connected to the appropriate test equipment. Select the
appropriate test and follow the onscreen prompts.
Transmit Digital [TXAD] Conventional Mixed-Mode Transmit Channels When
Transmit Digital is on, channels programmed for mixed-mode transmit will
transmit in digital mode. When off, mixed-mode channels transmit in analog
mode. When transmitting in digital mode the display shows D’ behind the TX indicator. In analog transmit,
A” will follow the indicator. Transmit Digital
selection can be assigned as a button, switch or menu list item. When assigned
as a button function, the “TXAD” button will be highlighted when in the
Transmit Digital mode.
– 52 –
BKR9000 Portable Radio User’s Manual
Transmit Power [PWR] Conventional and Trunking Channels Transmit Power can be
selected between the programmed high and low settings. The power output of the
settings depend on radio options, model and editor settings. When operating in
the high power mode, “H” will be displayed on the top line of the LCD. In low
power mode, “L” is displayed. Power selection can be assigned as a button,
switch or menu list item.
Two-Tone Select [TONE] Conventional Analog Channels Allows the user to select
from their two-tone list (programmed with RES). Selecting an item will send
the two-tone signal.
Versions
Conventional and Trunking Channels Version information about your radio can be
viewed via the “Versions” menu item. To review the information, open the
Versions menu. Use the NEXT or PREV to view the installed revisions of
individual items. Version information includes:
Radio Name (if programmed): Radio name. Date: Date of release. Release:
Overall release code. Software: Release code for ARM. DSP: Release code for
DSP. File Format: Currently installed file format. BSP: Release code of
installed BSP firmware. PCB Revision: Installed printed circuit board revision
number. Date of Manufacture: Date of manufacture.
Current version information can be found in the service section at
www.bktechnologies.com.
Voice Annunciation Mute [MUTE] Conventional and Trunking Channels Voice
Annunciation Mute on/off control can be assigned to a
– 53 –
BK Technologies switch, button or as a menu item. This will mute the radio’s
voice announcements.
Zone Select [ZONE] (Conventional and Trunked Channels)
Zone Select allows the radio user to switch between programmed channel zones.
The Zone Select operation can be assigned as a button, switch or menu list
item.. When Zone is assigned to a button, press the button to open the menu of
available zones. When assigned as a menu item, open the menu as described in
the Navigation section. Select the Zone you want to use. Press “ENTER” select
the Zone. Also, If enabled, a zone can also be accessed directly from the
keypad. (Refer to the RES help file.) (See also, Channel/Zone Selection
Options.)
– 54 –
BKR9000 Portable Radio User’s Manual
Keypad Programming
Radio programming is to be performed only by authorized personnel. Any or all
functions may be password protected to prevent unauthorized access. Check with
your communications officer for information on the programmed functions of
your radio.
NOTE: Trunking channels and systems cannot be programmed via the radio keypad.
Keypad programmable categories include individual Channel, Zone and Global
radio parameters, individual P25 ID Quick Call/Receive List, User Tone List,
User NAC List and User Talk Group ID List.
Check with your BK Technologies dealer or communications officer for
information on the programmed functions of your radio.
Keypad Programming Navigation
While in programming mode the diamond, arrow up, arrow down and square buttons
are used navigate the programming functions. The following table shows
possible button functions:
Keypad Programming Buttons
ENT Opens the highlighted function or enters the displayed information
ESC
Press once to go back to previous screen or hold to exit programming mode and return to normal radio operation
NEXT Move to the next item in a displayed list or the next character in a displayed value
PREV Move to the previous item in a displayed list
EDIT Used to select and edit individual characters in a displayed value
BACK Move to the previous character in a displayed value
CLR Clears the displayed value
EDIT Used to edit individual characters in a displayed value
INV
Inverts a displayed digital tone value (CDCSS)
Entering Keypad Programming Mode
To enter programming mode open the menu list by pressing the assigned “Menu”
button and select “Keypad Prog” from the menu list. Use the keypad to enter
the six-digit user or master password and press the Enter button.
– 55 –
BK Technologies
Select the item to program and press Enter.
Available programmable functions are: Keypad – Used to edit individual channel
and zone information such as labels, frequencies, operating modes, etc. Call
List – Used to edit the P25 ID Call List entries. User Tones – Used to edit
the user selectable Code Guard entries. User NACs – Used to edit user
selectable Network Access Codes. User TGIDs – Used to edit user selectable P25
Talk Groups
NOTE: Depending on PC programming, not all functions may be accessible for
keypad programming.
Global, System, Zone and Channel Parameters
The “Keypad” programming menu consists of four sub-menus for editing global,
system, zone and channel parameters (see table).
Global Display Top Display Middle Display Bottom User Password
Keypad Programming Sub-Menus
System Sys Pri 1 Tx on Pri 1 Sys Pri 2
Zone Add/Delete Label Zone Pri 1 Tx on Pri 1 Zone Pri 2
Channel Add/Delete Label Rx/Tx Freq Rx/Tx Mode Rx/Tx Guard
Rx/Tx NAC Sq Mode Bandwidth Tx Power TGID
Global Settings
To edit the programmable Global settings, select “Keypad” from the programing
menu then select “Global” from the sub-menu.
Select the item you wish to edit from the Global menu.
Displayed Information Lines The three main display lines can be programmed
with RES to display radio information. Select top, middle or bottom line to
change its displayed information. Then select the desired setting from the
list (see table).
NOTE: Display changes do not affect the display on trunked channels.
– 56 –
BKR9000 Portable Radio User’s Manual
Conventional Display Line Options
None Channel Label
Channel Number
No information is displayed.
Alphanumeric label of currently selected channel or active scanned channel.
Channel number of currently selected channel or active scanned channel.
Channel # and Zone Date and Time
Currently selected channel numbers and zone. Displays date and time.
DTMF Frequency
MDC*
Displays the numeric DTMF tones of received signal.
Operating frequency of currently selected channel or active scanned channel.
Displays the numeric MDC ID or received signal DTMF.
Radio Name Received TGID
Displays radio name.
P25 Talk Group ID of the radio transmitting the message currently being
received.
Rx’d Unit ID
P25 ID of a received digital signal. If the incoming ID is programmed in your Unit ID Call List list, the associated label will be displayed. During standby you radio ID number is displayed.
Rx/Tx Key
Currently selected encryption key.
Rx Picklist Selections* NAC, TGID or Code Guard currently selected from the programmable RX Pick Lists.
Subaudible Tx Picklist Selections
Unit ID
Displays CxCSS value of received signal.
NAC, TGID or Code Guard currently selected from the programmable TX Pick
Lists.
Shows your P25 Unit ID
While receiving, the ID of the radio transmitting the message is displayed
If the received ID is programmed in your radio’s Call List, the corresponding label will be displayed
Zone Label
Label of currently selected zone.
Zone and Channel # Currently selected zone and channel numbers.
Zone Number
Currently selected zone number.
*Conventional Channels Only
– 57 –
BK Technologies
User Password Select “User Password” from the “Global” menu to edit the keypad
programming password. Enter a six-digit numeric. NOTE: Changing the user
password does not affect the power-up or administrator password.
System Settings To edit the programmable System settings, select “Keypad” from
the programing menu then select “System” from the sub-menu. Select the item
you wish to edit from the System menu.
System Priority 1 or 2 Channel Priority channels can be assigned on a system
wide basis. If assigned, a system priority channel will be monitored during
priority scan regardless of the current operation zone priority channel. When
set to “Off”, the Priority 1 or Priority 2 Channel is designated by the
selected zone setting. When set to “Use Main” the channel selected by the
channel knob operates as the priority channel. To designate a specific
priority channel choose “Select” from the priority channel menu. Select the
Zone and Channel.
Tx on Priority 1 Channel If on, the radio will transmit on the System Priority
1 channel whenever Priority Scan is on.
Zone Settings To edit the programmable Zone settings, select “Keypad” from the
programing menu then select “Zone” from the sub-menu. Select Add, Delete or
Edit Zone from the Zone menu.
Add Zone When selected, a new zone is added in the next available slot.
Example: If there are seven zones in the radio, the added zone will be zone
eight.
– 58 –
BKR9000 Portable Radio User’s Manual
Delete Zone When selected the list of available zones is displayed. Choose the
zone you wish to delete. When a zone is removed all subsequent zones move up
one spot. Example: If there are seven zones in the radio and zone five is
deleted, zone six now becomes zone five and zone seven becomes zone six.
Edit Zone Select “Edit Zone” to change the programmable zone information.
Zone Label Use the keypad to enter a label of up to sixteen characters. (See
keypad character table)
Zone Priority 1 or 2 Channel NOTE: If system priority channels are programmed,
zone priority settings are ignored.
When set to “Off”, the Priority 1 or Priority 2 Channel is designated by the
selected zone setting. When set to “Use Main” the channel selected by the
channel knob operates as the priority channel. To designate a specific
priority channel choose “Select” from the priority channel menu and choose
from the channel list.
Zone Tx Priority 1 Channel If on, the radio will transmit on the Zone Priority
1 channel whenever Priority Scan is on and there is no system priority 1
programmed.
Channel Settings To edit the programmable Channel settings, select “Keypad”
from the programing menu then select “Channel” from the sub-menu. Select Add,
Delete or Edit Channel from the Channel menu. NOTE: REFER TO THE COMMAND ZONE
OPERATIONS SECTION FOR ADDING OR DELETING COMMAND ZONE CHANNELS. DO NOT ADD OR
DELETE COMMAND ZONE CHANNELS VIA THE KEYPAD PROGRAMMING METHOD.
– 59 –
BK Technologies
Add Channel Select to add a new channel. Choose the zone to which the channel
is to be added. Enter a valid channel index number of 1-5000. NOTE: To access
channels above channel sixteen, the radio must be programmed via PC for keypad
channel select or “Channel Select” must be assigned as a button or menu item.
Delete Channel When selected the list of programmed zones is displayed. Choose
the zone of the channel you wish to delete. Select the channel from the list.
Edit Channel Select “Edit Channel” to change the programmable channel
information. Select the zone and channel to be edited.
Channel Label Use the keypad to enter a label of up to sixteen characters.
(See keypad character table)
Rx Frequency Enter a valid receive frequency in MHz. Frequencies must be
divisible by 1.25kHz.
Rx Mode Select Analog, Digital or Mixed Mode.
Rx Guard Analog or Mixed Mode Receive Channels Only Select “Off” for analog
signals to operate in carrier squelch mode. Select “Tone” to enter a CTCSS
tone, Select “Digital” to enter a DCS value. Use “INV” to invert a DCS tone.
RX NAC Digital or Mixed Mode Receive Channels Only Select “Enter” to program a
receive NAC via the keypad. Enter the desired value in hexadecimal (000 –
FFF).
– 60 –
BKR9000 Portable Radio User’s Manual
NOTE: $F7F is an invalid receiver NAC. Choose “Select” to use a receiver NAC
from the programmed pick list.
Squelch Mode Digital or Mixed Mode Receive Channels Only
Normal – Requires carrier and NAC only to unmute digital signals. Selective –
Required for Individual Calls and use of Talkgroup IDs. Requires a matching
TGID to unsquelch.
Bandwidth Analog or Mixed Mode Channels Only
Narrowband – 12.5kHz spacing when operating in analog. Wideband – 25kHz
spacing when operating in analog.
Tx Power Low Power – Lock channel in low power mode. High Power – Lock channel
in high power mode. Selectable – Allow high/low transmit power selection form
assigned button, switch or menu item.
Tx Frequency Enter a valid receive frequency in MHz. Frequencies must be
divisible by 1.25kHz.
Tx Mode Select Analog, Digital or Selectable.
Tx Guard Analog or Mixed Mode Receive Channels Only Select “Off” for analog
signals to operate in carrier squelch mode. Select “Tone” to enter a CTCSS
tone, Select “Digital” to enter a DCS value. Use “INV” to invert a DCS tone.
Tx NAC Digital or Mixed Mode Transmit Channels Only Select “Enter” to program
a transmit NAC via the keypad. Enter the desired value in hexadecimal (000 –
FFF).
– 61 –
BK Technologies
NOTE: $F7E and $F7F are invalid transmit NACs. Choose “Select” to use a
transmit NAC from the pick list.
TGID Digital or Mixed Mode Channels Only Select “Enter” to program a transmit
Talk Group ID via the keypad. Enter the desired value (1- 65535). NOTE: 0 is
an invalid transmit Talk Group ID. Choose “Select” to use a TGID from the pick
list.
P25 ID Unit Call/Receive List
The BKR9000 can be pre-programmed with up to 512 Project 25 IDs and labels. If
`RX’d Unit ID’ is designated as a display line, the P25 ID of the radio
sending the call will be shown when receiving a digital signal. If the P25 ID
of the received call is programmed in the Call List, the alphanumeric label
associated with the ID will be displayed. If the P25 ID is not in the Call
List, the numeric P25 ID will be displayed.
Select “Call List” from the programing menu. Select the P25 ID you wish to
edit. The display shows the label and P25 ID of the selected ID. Select
“Label” to edit or add an alphanumeric label. Select “Dest ID” to change the
P25 ID.
User Selectable Code Guards
The BKR9000 can be pre-programmed with up to 32, user selectable, CTCSS or
CDCSS subaudible tones. Tones are selected via a programmed button or menu
item (see TX/RX CxCSS Picklist). If enabled, the tones can be programmed via
the radio’s keypad. Select “User Tones” from the programing menu. Select the
tone to edit. To enter a CTCSS tone select “Tone” and enter the desired
frequency in Hertz (67.0 – 254.1 Hz). To enter a CDCSS (digital) tone select
“Digital” then enter the three digit
– 62 –
BKR9000 Portable Radio User’s Manual
code. Use the INV button to invert the code. The following tables show the standard values for tone and digital. Any value can be entered in keypad programming. The user is not restricted to these values.
Valid Code Guard Tone Values
Group A
Group B
Group C
67.0 (XZ)
*151.4 (5Z) 71.9 (XA)
146.2 (4B) 74.4
77.0 (XB)
162.2 (5B) 82.5 (YZ)
156.7 (5A)
79.7
88.5 (YB)
173.8 (6A)
94.8 (ZA)
167.9 (6Z)
85.4 (YA)
*100.0 (1Z) 186.2 (7Z)
103.5 (1A)
*179.9 (6B) 91.5 (ZZ)
107.2 (1B)
203.5 (M1) 110.9 (2X) 192.8 (7A)
114.8 (2A)
218.1 (M3)
*118.8 (2B) 210.7 (M2)
123.0 (3Z)
233.6
127.3 (3A)
225.7 (M4)
131.8 (3B)
250.3
136.5 (4Z)
241.8
141.3 (4A)
- 50/60 Hz power distribution systems could cause falsing. The assignments in a given area should be made from within one of the Groups: A, B, or C.
Valid Digital Code Guard Values
023 025 026 031 032 043 047 051 054 065 071 072 073 074 114 115 116 125 131
132 134 143 152 155 156 162 165 172 174 205 223 226 243 244 245 251 261 263
265 271 306 311 315 331 343 346 351 364 365 371 411 412 423 431 432 445 464
465 466 503 506 516 532 546 565 606 612 624 627 631 632 654 662 664 703 712
723 731 732 734 743 754
– 63 –
BK Technologies
User Selectable Network Access Codes
The BKR9000 can be pre-programmed with up to 32, user selectable NACs. NACS
are selected via a programmed button or menu item (see TX/RX Network Access
Code Picklist). If enabled, the tones can be programmed via the radio’s
keypad. Select “User NACs” from the programing menu. Select the NAC to edit.
Enter the desired value in hexadecimal (000 – FFF). NOTE: $F7E and $F7F are
invalid as user selectable NAC values.
User Selectable Talkgroup IDs
The BKR9000 can be pre-programmed with up to 32, user selectable TGIDs. TGIDs
are selected via a programmed button or menu item (see Talk Group ID
Picklist). If enabled, the TGIDs can be programmed via the radio’s keypad.
Select “User TGIDs” from the programing menu. Select the Talk Group ID to
edit. Enter the desired value (1 – 65535). NOTE: A Talk Group ID value of 0 is
not allowed.
– 64 –
BKR9000 Portable Radio User’s Manual
BK Technologies Warranty Information
For the latest warranty information, visit:
https://www.bktechnologies.com/service-portal/factory-service/warranty
All repairs must be performed by an authorized BK Technologies service center
during the life of the warranty. Except for duration and factory-only repair,
extended warranties are identical to our standard 2 year warranty. Factory
extended warranties cover all BK Technologies portables, mobiles and base
stations and must be purchased at point of sale.
For information about your warranty contact BK Technologies: Phone:
800-648-0947 Email:
sales@bktechnologies.com
If you need service, contact your BK Technologies dealer. If you find it
impractical to have service provided by your dealer, contact the BK
Technologies Technical Service Department at
800-422-6281. Repairs may be sent to
the address below.
BK Technologies
Attention: Customer Service 7100 Technology Drive West Melbourne, FL 32904
– 65 –
BK Technologies
Keypad Text/Programming Characters
1 2 ABC
1 A, B, C, a, b, c, 2
3 DEF 4 GHI
D, E, F, d, e, f, 3 G, H, I, g, h, i, 4
5 JKL 6 MNO 7PQRS 8 TUV
J, K, L, j, k, l, 5 M, N, O, m, n, o, 6 P, Q, R, S, p, q, r, s, 7 T, U, V, t, u, v, 8
9WXYZ
W, X, Y, Z, w, x, y, z, 9
0
0, Blank Space
*, ., ,, ;, :, “, ‘, !, ?, %, &, ‘, ~, @, _
, $, +, -, =, ^, /, , |, <, >, {, }, [, ]
– 66 –
BKR9000 Portable Radio User’s Manual
My Radio Settings
Serial #
ID#
Conv.
Trunked
Collar Switch
Orange Button
Top Side
Middle Side
Bottom Side
Left Front
Center Front
Right Front
Menu Settings
Conv.
Trunked
– 67 –
References
- Home - BK Technologies
- Acceptable knowledge database, other supplementary procedures and notices
- BK Technologies - Service Portal
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>