BK TECHNOLOGIES BKR0701 Cloning Cable Adapter Instruction Manual
- June 3, 2024
- BK TECHNOLOGIES
Table of Contents
BKR0701 Cloning Cable Adapter
Instruction Manual
Operation
The BKR0701 Cloning Adaptor offers radio users the ability to share programmed
information between BKR portable and KNG portable radios. For proper
operation, the BKR0701 Cloning Adaptor must be used in conjunction with the
KAA0700 Cloning Cable.
For BKR to KNG cloning, one BKR0701 Cloning Adaptor and one KAA0700 Cloning
Cable are used as shown below:
For BKR to BKR cloning, one BKR0700 Cloning Adaptor should be used.
The Source radio is a radio programmed with the desired radio frequencies and
settings you wish to transfer to another radio of the same frequency range.
In order to clone radio information the Source radio must have a menu item
programmed, via PC Radio Editor, to allow cloning. (Refer to the
“Menus/Controls” section of the radio editor.)
The radio receiving the program is referred to as the Target.
Target radios can be programmed to block incoming cloning information on a
zone-by-zone basis.
Source Radio
On the Source, the radio selects the zone with the information to be cloned by
pressing the Zone button, or selecting “Zone Select” from the menu, then
entering the number of the desired zone.
On the Target, the radio selects the Zone or Group to which the information is
to be sent.
Some zones may be blocked by PC programming to prevent them from being
overwritten. Only unlocked groups will accept incoming clones.
Sending Information
On the Source radio:
- Press the Menu button. 2. Use the [PREV]/[NEXT] buttons to select “Cloning”.
3. Press the [ENT] button to send the cloning information.
While sending information “Cloning in Progress” will be shown on the Source radio display.
After successful radio data transfer, “Source Clone Complete” is briefly displayed on the Source radio.
Receiving Information
Target radios display a message to indicate receiving incoming information.
Target radios display “Destination Clone Start” during the cloning process.
When the cloning process is successfully completed, the Target radio will
automatically shut down and reset.
NOTE : Upon reset, the Target radio reverts to Zone 1.
Error Notifications
Source Clone Error| If the targeted zone is blocked from cloning, or the clone
is not successful for any other reason,
the Source radio will display “Source Clone Error” and require radio power to
be cycled.
---|---
Destination Clone Locked| If a targeted zone is blocked from cloning the
Target radio will display the “Destination Clone Locked” message and requires
radio power to be cycled.
Target Radio
To clone to a BKR or KNG radio, it must be put in “Destination Clone Mode.” The BKR and KNG radio can only receive “Active Zone” or “Picklist” clone information.
| On the target radio:
1. Select the Menu button.
2. Use the up/down buttons to select “Cloning”.
3. Press the [ENT] button.
4. Select “Enter Dest Clone”.
---|---
| When the target radio is in “Destination Clone Mode”, the source radio can
initiate the cloning of the “Active Zone” or “Picklist”.
Destination Clone Start| When cloning has started, the target radio will
display “Destination Clone Start”
Powering Off| After a successful information transfer, “Power off” is
displayed and the radio will restart.
Zone to Zone Unsupported| The only cloning functions supported by the KNG
Target radio are “Active Zone” and “Picklist”. All other functions are
unsupported.
Cloneable Information
The Source radio sends only information the Target radio requires.
Channel Capacity Considerations
When a BKR Source zone is programmed with fewer channels than a Target radio,
channels about the highest programmed Source channel will be set to inactive.
A Target zone will assume the channel structure of the Source radio.
Example : Cloning from a BKR with a five-channel zone will enable only
five channels in the Target radio.
BKR and KNG radios do not allow a receive frequency of 0. When a Source radio
channel has no programmed receive frequency, the Target will substitute
136MHz.
Picklist Capable Target Radio Considerations
If picklist selections are assigned in the Source radio, the associated
picklist reference will be cloned to the Target radio. For example, if a
channel has a picklist selection of Tone 3, then a picklist reference of 3
will be sent to the Target radio and the Target radio will use the value
stored in the 3 positions of the radio’s picklist. The Target radio’s
picklists
will not be affected.
Cloned Picklist Values
Source radio | BKR | KNG |
---|---|---|
Tone selected | Default values and Picklist references | Default values and |
Picklist references
No tone selected| Default values| Default values
If the cloning process fails or the Target radio’s zone is blocked from
accepting an incoming clone, a fail message will appear on the Source radio.
Failure of downloading can be due to:
- Zone programmed to block clone
- Improper connection
- Failure to turn on the Target Radio
- Incompatible Target radio
- Cable unplugged
American Communication Systems
Discover the Power of Communications
http://www.ameradio.com
Documents / Resources
| BK
TECHNOLOGIES BKR0701 Cloning Cable
Adapter
[pdf] Instruction Manual
BKR0701, Cloning Cable Adapter, BKR0701 Cloning Cable Adapter, Cable Adapter,
Adapter
---|---
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>