VEVOR PA200 Electric Mini Hoist User Manual
- October 30, 2023
- VEVOR
Table of Contents
VEVOR PA200 Electric Mini Hoist
Congratulations for your excellent choice our new electric tool is manufactured in compliance with the best and reliability standards,ensuring you efficiency and safety for a long period of time
SPECIFICATION
Model| Method of use| Rated Vol(V)| Input Power (W)| Rated lifting weight
(kg)| Lifting Speed (m/min)| Lifting Quan Packing G.W/Height /CNT Dimension
N.W (m) (PCS)
(cm) (kg)
---|---|---|---|---|---|---
PA200| Single-hook| 110/220| 480| 100| 10| 1 381422 11/12 (5/6/10/12)
| Double-hook| | | 200| 5|
PA250| Single-hook| 110/220| 510| 125| 12| 1 381422 11/12 (5/6/10/12)
| Double-hook| | | 250| 6|
PA300| Single-hook| 110/220| 600| 150| 10| 1 381422 11/12 (5/6/10/12)
| Double-hook| | | 300| 5|
PA400| Single-hook| 110/220| 850| 200| 12| 1 441524 15/16 (5/6/10/12)
| Double-hook| | | | |
PA500| Single-hook| 110/220| | 250| 10| 1 441524 15/16 (5/6/10/12)
| Double-hook| | | 500| 5|
PA600| Single-hook| 110/220| | 300| 12| 1 441524 16/17 (5/6/10/12)
| Double-hook| | | 600| 6|
PA800| Single-hook| 110/220| | 400| 10| 1 441524 19/20 (5/6/10/12)
| Double-hook| | | 800| 5|
PA1000| Single-hook| 110/220| | 500| 12| 1 592431 30/31 (5/6/10/12)
| Double-hook| | | 1000| 6|
PA1200| Single-hook| 110/220| | 600| 10| 1 592431 31/32 (5/6/10/12)
| Double-hook| | | 1200| 5|
GENERAL SAFETY RULES
WARNING! Before using this electric tool. Carefully read the general safety rules listed below.
- Your sockets must comply with safety rules.In case your sockets are not suitable,it should be checked by a skilled electrician.
- Your socket plug must absolutely be grounded and your electric system must be supplied with a magneto cut-out safety.
- When the machine is running unwatched, be careful that children cannot reach it.
- Do not pull the electric cable to disconnect the plug.
- The machine shall be protected from frost and low temperatures.
- In case the machine cannot hoist a load, do not keep pressing the hoisting push button: th is means that the load exceeds the machine maximum capacity.
- The machine shall not be disassembled when running or connected to power.
- Do not stand under hoisted weights.
- Before starting the work, make sure that the steel cable is correctly winded around the reel and the pitch is equal to the cable diameter.
- Observe the maximum load indicated on the hoist, not that no the hook!
- Leave at least three turns of cable around the reel, so that the cable connection is not under stress.
- To avoid any danger, do not wind more than 15m of cable around the reel.
- In case the steel cable is worm out, it must be replaced only with a cable of same features manufactured by us. If can be found at all authorized service shops.
- Before starting the word, check that switches are in good operating conditions.
- In case the hoist stops during the lowering of a load, it is normal that he load goes down a few centimeters more because of inertia.
- Attention! The hoist electric motor is not supplied with any overload cut-out(to avoid an unexpected and unwanted restart) therefore, if you are unable to hoist a load do not insist and let the motor cool down.
MAINTENANCE
Periodically CHECK that the steel cable is in good conditions.
- CHECK that the screws securing the brackets and reduction gear are well tightened.
- CHECK THE CONDITIONS AND TIGHTENING OF THE NUTS securing the steel cable clamps.
- Periodically CHECK that motor stop switch and push button switch are in good operating conditions.