Roth Minishunt Room Thermostat Installation Guide

: June 10, 2024
: Roth

Table of Contents

Roth room thermostat
References
Read User Manual Online (PDF format)
Download This Manual (PDF format)

Minishunt Room Thermostat
Installation Guide Living full of energy

Roth room thermostat

|
---|---
|
|

Remove screw and slide backplate off.
Insert batteries (included), be aware of +/- polarity.
Mount backplate on the wall (screws not incl.) thermostat slides onto back plate.
Pairing/registering the thermostat. All connections must be made to the Controller (pump, actuator before start-up. Please see controller manual for details. Press the registration button on the left side of the control unit (see picture 5) and then press the registration button on the room thermostat (see picture 6). The temperature is now shown in the display.
Attention! Do not press the buttons on the front of the thermostat whilst pushing the pairing button on the rear (see picture 6).
Once the thermostat is connected to the Zone/Channel, the display shows the temperature on the thermostat.
In the event of a power failure, the connection between the room thermostat and the receiver is restored within 5-10 minutes.

Operation of thermostat.
In order to enter MENU press and hold () button. Use < > buttons to navigate between MENU settings.

| In sleepmode the current temperature is displayed. To set/change temperature press <> buttons. Confirm by pressing  or wait 5 sec.
---|---
| You can switch between temperature display and relative humidity display by briefly pressing the  button.
| You can choose between three modes on the thermostat. After changing the setpoint with< />the actual setting is flashing: “Con” means setpoint is due constantly.
| “5 H” means that the desired setpoint will be valid for the next 5 hours, after this the thermostat will return to it’s normal mode.
| “OFF” means that it follows the mode preset on the Controller. The chosen mode can also be seen on the Con- troller display. Changing the mode ”Con”, “5h” and “OFF” is done using the buttons < />whenthe mode is flashing.
| Enables you to view battery level. Select “Bat”, the display flashes. Confirm within 5 sec. after which the battery level is dis- played in percentage %.
| Enables you to lock the buttons. Select “Yes” by using one of the buttons <

, confirm by pressing  or wait 5 seconds. When the lock is active, the keys are locked automatically
after 10 seconds of inactivity. To unlock, press and hold the bottons < > for 10 sec. The keys are accessible when the display returns to showing the current temperature. The
key lock is activated until you inactivate it in the menu.
| Enables you to return the room thermostat to the factory setting. Select “dEF” and the display flashes and shows the selected value. Select/confirm (Yes) with < > buttons within 5 sec. Confirm by pressing  or wait 5 sec. and the factory settings has be restored.
| Enables you to view the sensor calibration value. Afyer selecting ”Cal” the screen flashes for 3 sec. and the value is displayed. Value can be changed on the Controller, please see user manual.
| Enables you to return from the MENU manually. After selecting ”rEt” the screen flashes for 5 sec. and returns to view of the current temperature.

https://rebrand.ly/Minishunt
Roth Minishunt QR

ROTH DANMARK A/S
Centervej 5
3600 Frederikssund
Tlf. +45 4738 0121
E-mail: service@roth-danmark.dk
roth-danmark.dk| ROTH SVERIGE AB
Höjdrodergatan 22
212 39 Malmö
Tel. +46 40534090
Fax +46 40534099
E-mail: service@roth-sverige.se
roth-sverige.se
---|---
ROTH NORGE AS
Billingstadsletta 19
1396 Billingstad
Tel. +47 67 57 54 00
E-mail: service@roth-norge.no
roth-norge.no
facebook.com/RothNorge| ROTH FINLAND OY
Raaseporintie 9 (Talo 2)
10600 Tammisaari
Puh. +358 (0)19 440 330
S-posti: service@roth-finland.fi
roth-finland.fi
facebook.com/RothFinland