Roth EPS 30 Universal Plade Installation Guide

: June 10, 2024
: Roth

Table of Contents

Technical data
General structure
References
Read User Manual Online (PDF format)
Download This Manual (PDF format)

Roth Universal Blade EPISODE 30
16 & 20 mm
Installation Roth EPS 30 Universal Plade -

Technical data

Plumbing no.	339314.03
Goal	height 30 mm,

width 600 mm,
length 1200 mm
Areal| 0,72 m²
1 package = 8,64/m²
Sport| 2 pcs. with C/C 300 mm and 3 pcs. with C/C 200 mm
Material| 30 mm expanded polystyrene, Density 33 kg/m³,
Compressive strength 250 kPa
Insulating ability| 0,033 W/m K
Consumption per m²| 1.40 plates
Pipe consumption per m²| 3,3 m for 20 mm og 5,0 m for 16 mm
Upper floor min. thickness| 14 mm wood/laminate (floor supplier may require a pressure compensating plate)
The weight of the floor construction step sound attenuation| Δ Lw = 18 dB
Improved sound insulation| Δ R’ w = dB

Roth Universal plate EPS 30 can be laid on almost any type of surface, as long as it is stable and load-bearing. It can be concrete and timber structures or on other insulation. It is possible to use two dimensions on the Roth Universal plate EPS 30 system, either 16 mm or 20 mm and possibly a combination of these. See picture lb.
Step 1
The floor must be cleaned, swept/stray vacuumed before you start laying the Roth Universal board EPS 30. Check that the floor is horizontal and without gaps. Image la is shown as 0 20 mm C/C 300.

Roth EPS 30 Universal Plade - fig 1 | Roth EPS 30
Universal Plade - fig 2
---|---

Step 2
When laying out the plates, you choose the desired rudder dimension that you want to work with. This is marked at all tracks and turning plates. If you deviate, for example, 20 mm with a tube spacing of C/C 300 mm, you must pay attention to the fact that the end of the plate marked with 20 mm must be the plate that ends with the wall of the clamp. The same naturally applies to 16 mm with a rudder distance of C/C 200 mm. The boards can be shortened with a knife, use the screws on the back. Image 2 is shown as 0 16mm C/C 200mm.

Roth EPS 30 Universal Plade - fig 3

Step 3
The Roth Universal plate EPS 30 system is now laid out and you can start to adapt the heat distribution plates. The boards are laid down in the tracks with a mutual distance of 10 – 20 mm. It is clearly marked on the Roth Universal’)lade EPS 30 system where the laying out of the heat distribution plates must end. The heat distribution plates can be shortened using the bending instructions on the plates. Do not use tools for shortening, as this can cause burrs in the rudder grooves.
Step 4
Pipe lining is carried out according to often the chosen sample of laying in the selected pipe dimension.

Roth EPS 30 Universal Plade - fig 4 | Roth EPS 30
Universal Plade - fig 5
---|---

General structure

Laying of floorboard or floor foam can now be carried out according to the floor manufacturer’s instructions. When laying wooden floors, we recommend that it is laid across the direction of the pipes. Check the recommended wood floor thickness according to the manufacturer’s instructions, our data sheet and applicable legislation.
Roth Universal plate EPS 30 can be used together with Here makes of upper floors and sub-floors. We always recommend contacting the supplier for advice and support regarding correct construction. If the upper floor is to be tiles/tiles, we recommend using Fermacell 25 mm floor elements.
Example: Construction with Fermacell 25 mm floor element
Roth Universal plate EPS 30 can also be used in conjunction with tiles, studs or vinyl. If the upper floor is to be tiles/tiles, we recommend using Fermacell 25 mm floor elements. In the case of tiles, the subfloor must be sufficiently level. This can be achieved by building on concrete or 22 mm chipboard/19 mm plywood, laid on beams/beams C/C 300 mm. Before commencing installation, we always recommend that you contact Fermacell Scandinavia for advice and support regarding correct construction.

ROTH DANMARK A/S
Centervej 5
3600 Frederikssund
Tlf. +45 4738 0121
E-mail: service@roth-danmark.dk
roth-danmark.dk| ROTH SVERIGE AB
Höjdrodergatan 22
212 39 Malmö
Tel. +46 40534090
Fax +46 40534099
E-mail: service@roth-sverige.se
roth-sverige.se
---|---
ROTH NORGE AS
Billingstadsletta 19
1396 Billingstad
Tel. +47 67 57 54 00
E-mail: service@roth-norge.no
roth-norge.no
facebook.com/RothNorge| ROTH FINLAND OY
Raaseporintie 9, Talo 2
10600 Tammisaari
Puh. +358 (0)19 440 330
S-posti: service@roth-finland.fi
roth-finland.fi
facebook.com/RothFinland