Laserliner StarSensor 50 Electronic Scanners Instruction Manual
- June 10, 2024
- Laserliner
Table of Contents
StarSensor 50 Electronic Scanner
StarSensor 50 Product Information
The StarSensor 50 is an electronic locating device that is designed to find
wall beams and joists as well as live wires. The device analyses the surface
at five points simultaneously and signals the detection of concealed objects
via the LED display. The device can detect wooden wall beams and joists as
well as metal in
drywall structures, e.g. under gypsum fibreboard, wood panels or other non-
metallic cladding.
The StarSensor 50 has a messtiefe of up to 4 cm for Balkenortung (beam
detection) and up to 2 cm for Holz / Metals (wood/metal detection). The device
has a voltage measurement range of 110 – 230V, 50 – 60 Hz. The device is
powered by two 1.5V LR6 (AA) batteries and weighs 186 g (including battery).
The device’s
dimensions are 73.5 mm x 186 mm x 44 mm.
When using the StarSensor 50, it is important to observe the technical safety regulations for working on electrical systems, especially: 1. Safely isolating from power supply, 2. Securing to prevent system being switched on again, 3. Checking zero potential, two-pole, 4. Earthing and shortcircuiting, 5. Securing and covering adjacent live components.
StarSensor 50 Product Usage Instructions
- Read through the operating instructions, the Warranty and Additional Information booklet as well as the latest information under the internet link at the end of these instructions. Follow the instructions they contain.
- Open the battery compartment and insert two 1.5V LR6 (AA) batteries according to the symbols. Be sure to pay attention to polarity.
- To turn on the device, press and hold the On button (3).
- Move the device slowly across the surface to detect wooden wall beams and joists as well as metal in drywall structures.
- The LEDs indicate the centre and the edges of beams and hidden objects.
- The presence of live lines is indicated when the lightning symbols light up.
- To turn off the device, release the On button (3).
- To avoid interference while scanning, keep your free hand and other objects at least 15 cm away from the Stars Ensor 50.
- Ensure that you have really detected a stud. To do so, check on both sides whether other studs are present at equal distances, usually at 30, 40 or 60 cm. Also check that it is a stud by scanning at several places directly above and below the position of the first find.
- If an object is deep inside a wall, the device may not indicate it clearly.
Function / Application
This electronic locating device finds wall beams and joists as well as live wires. The device analyses the surface at five points simultaneously and signals the detection of concealed objects via the LED display.
General safety instructions
- The device must only be used in accordance with its intended purpose and within the scope of the specifications.
- The structure of the device must not be modified in any way.
- Do not expose the device to mechanical stress, extreme temperatures, moisture or significant vibration.
- Do not work alone in the vicinity of hazardous electrical installations and only under the guidance of a qualified electrician.
Additional information on use
Observe the technical safety regulations for working on electrical systems,
especially:
- Safely isolating from power supply,
- Securing to prevent system being switched on again,
- Checking zero potential, two-pole,
- Earthing and short- circuiting,
- Securing and covering adjacent live components.
Safety instructions
Dealing with electromagnetic radiation
- The measuring device complies with electromagnetic compatibility regulations and limit values in accordance with EMC-Directive 2014/30/EU.
- Local operating restrictions – for example, in hospitals, aircraft, petrol stations or in the vicinity of people with pacemakers – may apply. Electronic devices can potentially cause hazards or interference or be subject to hazards or interference.
- The measuring accuracy may be affected when working close to high voltages or high electromagnetic alternating fields.
- LED-Indicator
- Live wire warning
- ON
- Battery compartment
Inserting batteries
Open the battery compartment and insert batteries (2 x typ AA) according to
the symbols. Be sure to pay attention to polarity.
Operation
Device on: Press and hold the On button (3).
Scan: The LEDs indicate the centre and the edges of beams and hidden objects.
Live wire warning: The presence of live lines is indicated when the lightning symbols light up.
Device off: Release the On button (3).
Detecting wooden wall beams and joists as well as metal in drywall structures,
e.g. under gypsum fiberboard, wood panels or other non-metallic cladding.
Move the tool slowly across the surface.
Tip 1 : To avoid interference while scanning, keep your free hand and
other objects at least 15 cm away from the Star Sensor 50.
Tip 2: Ensure that you have really detected a stud. To do so, check on
both sides whether other studs are present at equal distances, usually at 30,
40 or 60 cm. Also check that it is a stud by scanning at several places
directly above and below the position of the first find.
Note: If an object is deep inside a wall, the device may not indicate it
clearly.
If electric wires or metal or plastic pipes are located near or in contact with a plaster fiberboard panel, they may be identified by the Star Sensor 50 as studs.
Special things to note with various materials
It may not be possible to detect wooden studs or joists through the following materials:
- Ceramic floor tiles
- Fitted carpeting with padded backing
- Wallpaper with metal fibres or metal foil
- Freshly painted, damp walls. These must have dried for at least one week.
Always switch off the power supply when working near electric wires.
Information on maintenance and care
Clean all components with a damp cloth and do not use cleaning agents,
scouring agents and solvents. Remove the battery(ies) before storing for
longer periods. Store the device in a clean and dry place.
Technical Data
(Subject to technical changes without notice. 21W47).
Technical Data
(Subject to technical changes without notice. 21W47)
Detection range AC| 110 – 230V, 50 – 60 Hz
Power supply| 2 x 1.5V LR6 (AA)
Operating conditions| 0°C … 40°C, max. humidity 20
… 90% rH, no condensation
Storage conditions| -10°C … 50°C, max. humidity 80% rH, no condensation
Dimensions (W x H x D)| 73,5 mm x 186 mm x 44 mm
Weight| 186 g (incl. batteries)
Measuring depth
Wood/metal beam location| up to 4 cm depth
Live wire warning| up to 2 cm depth
EU directives and disposal
This device complies with all necessary standards for the free movement of goods within the EU. This product is an electric device and must be collected separately for disposal according to the European Directive on waste electrical and electronic equipment. Further safety and supplementary notices at: http://laserliner.com/info?an=ALO
SERVICE
Umarex GmbH & Co. KG
– Laserliner –
Möhnestraße 149, 59755 Arnsberg, Germany
Tel.: +49 2932 638-300,
Fax: +49 2932 638-333 info@laserliner.com
Umarex GmbH & Co. KG Donnerfeld 2
59757 Arnsberg, Germany
Tel.: +49 2932 638-300,
Fax: -333 www.laserliner.com
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>