Cossiga Linear Series Food Display Cabinet Instructions

June 10, 2024
cossiga

Cossiga Linear Series Food Display Cabinet Instructions
Cossiga Linear Series Food Display Cabinet

SERVICING

Accessing fans and coil (RF)

  1. Unscrew base plates
    Instruction

  2. Remove trays
    Instruction

  3. Lift+ remove grills
    Instruction

  4. Lift panel to expose fans and coil
    Instruction

Deck height adjustment (RF)
Height adjustment
Use brackets provided to adjust deck height
Height adjustment

CERAMIC CLEANING

To thoroughly clean your glass ceramic cooktop, first remove dirt and food with suitable metal scraper or special sponge for glass ceramic cooktops.
CLEANING

Once the glass ceramic cooktop has cooled, put a few drops of suitable cleaner on it and rub it on with a paper towel, a clean cloth or an approved cleaning sponge.
CLEANING
Then wipe the glass ceramic cooktop with a damp cloth and dry it with a clean cloth or an approved cleaning sponge.

CONTROLLER INSTRUCTIONS

DIXELL CONTROLLER ONLY
CONTROLLER INSTRUCTIONS

PRESS FOR MORE THAN 3 SECONDS TO TURN ON EXTRA DEFROST

TO ADJUST TEMPERATURE

  1. PRESS AND HOLD FOR 3 SECONDS

  2. SET POINT WILL FLASH

  3. PUSH ARROWS TO ADJUST SET POINT

  4. PRESS SET TO CONFIRM

USER GUIDE FOR LINEAR SERIES

This is a guide only. If you are unsure of any aspects of the installation or operation, please contact us or visit our website www.cossiga.com

SAFETY

 Always disconnect this appliance before cleaning and servicing
 Servicing should only be carried out by an approved service agent, registered electrician or refrigeration engineer
 Do not use a multi-box or overload your power supply

INSTALLATION

Your cabinet has been delivered fully assembled.Please check nothing has moved during transit

AVOID
Installation

  • Drafts from doorways
  • Airflow from air-conditioning ducts
  • Hot air from motors i.e. refrigerators
  • Direct sunlight

Also applies to heat disruption on Bain Marie and Ceramic Top units
Installation

Check bench cutout is as per table on website
Installation
Installation

Lifting brackets are fitted to assist removing the unit from the packaging and placing in cabinetry. Use a bar that can fit through the 35 x 35mm square hole (not supplied)
Lift unit into place use lifting brackets
Installation
Use four people lifting each corner. After the unit has been placed in the required position remove lifting brackets.Retain bolts and screws for fixing the gantry post.

GANTRY ASSEMBLY

  1. Bain Marie (BM) & Ceramic Top(CM) Remove side post cover lift up and out from the base Position gantry assembly onto base screw up fixing bolts with washers from underneath on both sides. Lamp power cable – feed through large hole in deck
    Instruction

  2. Plug into socket and screw up Refrigerated(RF) gantry screw down from above. Screw gantry assembly down on to base.
    Instruction
    Instruction

  3. Install Cover
    On each side post slide up the post cover panel. position into clips and pull down to fit.
    Instruction

If the gantry is not used a blanking plate is supplied to cover gantry fixing holes. Insert into position each side and fix with a bead of food grade silione.
Instruction

GLASS ASSEMBLY

  • Flat Top
    GLASS

  • Double Curved
    GLASS

  • Full Square
    GLASS

EXTRACTION FAN

Fan Instruction
Fan Instruction
Recommended for optimising performance. Available as accessories with detailed drawings on our website.

SHELF ASSEMBLY

The 4 shelf clamps –

  1. Release bottom screw to open clamp
    SHELF ASSEMBLY

  2. Screw in clamp to post holes
    SHELF ASSEMBLY

  3. Insert glass shelf and centre. Tighten shelf clamps using underneath scew to suit.
    NOTE: LS5 – LS6 units come with a two piece glass mid shelf and bracket. The bracket is fixed to the middle underside of the lamp box
    SHELF ASSEMBLY

REFRIGERATION VENTILATION

Ensure condensor unit has adequate ventilation as per Cossiga specifications
Instruction
Make sure the fan is drawing cool air in and hot air can escape
Instruction

BAIN MARIE INSTALLATION

Your LS Bain Marie is dual purpose and can be run dry, manually filled wet or can be plumbed in for auto fill + drainage

DUAL PURPOSE WET OR DRY
Installation
Installation
Note:
The water stops just under the element. This provides good humidity with minimum steam.

FOR DRY OPERATION


Use stainless bracket to disengage float switch

BAIN MARIE

Needs to be kept clean to stop the build up of lime scale

Clean Daily
Clean with hot soapy water
Rinse + Dry
A commerical descaler may be required periodically

IF YOUR BAIN MARIE HAS NO POWER?

Check the ‘trip switch’ in the electrical box
RESET
If it continues to trip please call a service techician
Instruction
HALOGEN LAMPS

Life span of each bulb is between 1500 and 2000 hours which is approximately 7-10 weeks when running 24/7 or 27-35 weeks when running at 8 hours a day Bulbs are incredibly sensitive to vibration and can cause premature blowing or shattering.Ensure doors are not slammed and do not allow steam moisture to build on globes
Light

CONDENSER CLEANING

CLEANING
CLEANING

  • Better Performance
  • Lower Power Consumption
  • Longer Cabinet Life

EVAPORATION PANS

Designed to boil off excess water produced by your cabinet
NEED TO BE KEPT CLEAN!
Disconnect the power and unscrew and remove the rear cover to access pan
Remove water and wipe pan
( CAUTION: MAY BE HOT)

EVAPORATION

References

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals