cossiga Linear Series Refrigerated Buffet Display User Guide

: June 10, 2024
: cossiga

Cossiga Linear Series Refrigerated Buffet Display User Guide

USER GUIDE FOR LINEAR SERIES

Thank you for purchasing a Cossiga food display cabinet

This is a guide only. If you are unsure of any aspects of the installation or operation, please contact us or visit our website www.cossiga.com

SAFETY

Always disconnect this appliance before cleaning and servicing

Servicing should only be carried out by an approved service agent, registered electrician or refrigeration engineer

Do not use a multi-box or overload your power supply

INSTALLATION

Your cabinet has been delivered fully assembled.Please check nothing has moved during transit

AVOID

rafts from doorways
Airflow from air-conditioning ducts
Hot air from motors i.e. refrigerators
Direct sunlight

Check bench cutout is as per table on website
Lift unit into place use lifting brackets

Lifting brackets are fitted to assist removing the unit from the packaging and placing in cabinetry.
Use a bar that can fit through the 35 x 35mm square hole (not supplied)

Use four people lifting each corner.
After the unit has been placed in the required position remove lifting brackets. Retain bolts and screws for fixing the gantry post.

GANTRY ASSEMBLY

Bain Marie (BM) & Ceramic Top(CM)

Remove side post cover lift up and out from the base
Position gantry assembly onto base screw up fixing bolts with washers from underneath on both sides.
Lamp power cable – feed through large hole in deck
Plug into socket and screw up.
Refrigerated(RF) gantry screw down from above.
Screw gantry assembly down on to base.
Install Cover
On each side post slide up the post cover panel.
position into clips and pull down to fit.

If the gantry is not used a blanking plate is supplied to cover gantry fixing holes. Insert into position each side and fix with a bead of food grade silione.

GLASS ASSEMBLY

See separate glass assembly sheet provided

EXTRACTION FAN

Recommended for optimising performance. Available as accessories with detailed drawings on our website.

Extraction Fan

SHELF ASSEMBLY

The 4 shelf clamps –

Release bottom screw to open clamp
Screw in clamp to post holes
Insert glass shelf and centre.

Tighten shelf clamps using underneath scew to suit.
NOTE: LS5 – LS6 units come with a two piece glass mid shelf and bracket. The bracket is fixed to the middle underside of the lamp box

REFRIGERATION VENTILATION

key to the efficient running and long life

Refrigiration Ventilation

BAIN MARIE INSTALLATION

Your LS Bain Marie is dual purpose and can be run dry, manually filled wet or can be plumbed in for auto fill + drainage

Bain Marie Installation

BAIN MARIE

Bain Marie

HALOGEN LAMPS

Life span of each bulb is between 1500 and 2000 hours which is approximately 7-10 weeks when running 24/7 or 27-35 weeks when running at 8 hours a day

Bulbs are incredibly sensitive to vibration and can cause premature blowing or shattering.Ensure doors are not slammed and do not allow steam moisture to build on globes

Light Bulb Type
64243011
240V 300W
Clear Quartz Jacket
Halogen Infra-Red
Catering Lamp
R7s Cap

CONDENSER CLEANING

EVAPORATION PANS RF UNITS

Designed to boil off excess water produced by your cabinet

NEED TO BE KEPT CLEAN!
Disconnect the power and unscrew and remove the rear cover to access pan

Remove water and wipe pan
(CAUTION: MAY BE HOT)

SERVICING

key to maintaining your cabinets

Accessing fans and coil (RF)

Unscrew base plates
Remove trays
Lift+ remove grills
Lift panel to expose fans and coil

Deck height adjustment (RF)

Deck height adjustment

CERAMIC CLEANING

To thoroughly clean your glass ceramic cooktop, first remove dirt and food with suitable metal scraper or special sponge for glass ceramic cooktops.

Ceramic Cleaning Continued
Once the glass ceramic cooktop has cooled, put a few drops of suitable cleaner on it and rub it on with a paper towel, a clean cloth or an approved cleaning sponge.