HZ-1001-XNA Elite4B 8 Zone Outdoor Black Griddle
User Guide

HZ-1001-XNA Elite4B 8 Zone Outdoor Black Griddle

WARNING
The manufacturer has made every effort to eliminate any sharp edges. However, you should handle all components with care to avoid accidental injury.
NOTICE: Before assembly, make sure all parts are present. If any part is missing or damaged, do not attempt to assemble the appliance. Contact customer service for replacement parts at 1-833-572-1688.
NEED MORE INSTRUCTIONS?
Scan for registration, assembly videos, care + use, warranty, recipes, + more.

BATTERY NOT INCLUDED. Requires 1 AA battery for igniter.
IMPORTANT: Please read all instructions thoroughly before proceeding. Find a large, clean area in which to assemble your HALO Elite 4B Outdoor Griddle. Please refer to the assembly diagram, as necessary.

1. Install left inner leg using 3-M6 x 14 mm screws. Install leg cap.
   NOTICE: Make sure all the plastic protection is removed before assembling.
   Tool required for assembly: #2 Phillips Screwdriver

2. Install left outer leg using 3-M6 x 14 mm screws. Install leg cap.
   ITEM| PART DESCRIPTION| QTY| PART #
   ---|---|---|---
   31| Cap-Leg| 1| HZ-1001-48
   32| Left-Outer Leg-Long| 1| HZ-1001-23
   32A| Left-Outer Leg-Short| 1| HZ-1001-24
   45| M6 x 14 mm Screw| 3| HZ-1001-40
3. Install left outer leg assembly and left inner Leg assembly using pivot bracket 41 and 41A, 2-M6 x 3H Shoulder screws, M6 x 93 mm knob with threaded shaft and nylon spacer. Tighten screws firmly. Set assembly aside.
   ITEM| PART DESCRIPTION| QTY.| PART #
   ---|---|---|---
   41| Pivot Bracket-A| 1| HZ-1001-36
   41A| Pivot Bracket-B| 1| HZ-1001-37
   46| M6 x 93 mm Knob with Threaded Shaft| 1| HZ-1001-41
   48| M6 x 3H Shoulder Screw| 2| HZ-1001-43
   50| Nylon Spacer| 1| HZ-1001-45

WARNING
Pinch Points

4. Install right inner leg assembly using 3-M6 x 14 mm screws. Install leg cap.
   ITEM| PART DESCRIPTION| QTY.| PART #
   ---|---|---|---
   31| Cap-Leg| 1| HZ-1001-48
   34| Right-Inner Leg-Long| 1| HZ-1001-27
   34A| Right-Inner Leg-Short| 1| HZ-1001-28
   45| M6 x 14 mm Screw| 3| HZ-1001-40

5. Install right outer leg assembly using 3-M6 x 14 mm screws. Install leg cap.
   ITEM| PART DESCRIPTION| QTY.| PART #
   ---|---|---|---
   31| Cap-Leg| 1| HZ-1001-48
   35| Right-Outer Leg-Long| 1| HZ-1001-29
   35A| Right-Outer Leg-Short| 1| HZ-1001-30
   45| M6 x 14 mm Screw| 3| HZ-1001-40

6. Install right outer leg assembly and right inner leg assembly using pivot bracket 42 and 41A, 2-M6 x 3H shoulder screws, M6 x 93 mm knob with threaded shaft and nylon spacer. Tighten screws firmly. Set assembly aside.
   ITEM| PART DESCRIPTION| QTY.| PART #
   ---|---|---|---
   41A| Pivot Bracket-B| 1| HZ-1001-37
   42| Pivot Bracket-C| 1| HZ-1001-38
   46| M6 x 93 mm Knob with Threaded Shaft| 1| HZ-1001-41
   48| M6 x 3H Shoulder Screw| 2| HZ-1001-43
   50| Nylon Spacer| 1| HZ-1001-45

WARNING
Pinch Points

7. Install tank retention support bracket and rear brace using 2-M6 x 14 mm screws.
   ITEM| PART DESCRIPTION| QTY.| PART #
   ---|---|---|---
   37| Tank Support Bracket| 1| HZ-1001-32
   38| Rear Brace| 1| HZ-1001-33
   45| M6 x 14 mm Screw| 2| HZ-1001-40

8. Install tank retention, front panel and rear brace assembly using 10-M6 x 14 mm screws. Tighten screws firmly.
   IMPORTANT: Do not tighten screws completely until all screws for this step have been installed. ITEM| PART DESCRIPTION| QTY.| **PART

   **

   ---|---|---|---
   36| Tank Retention Wire| 1| HZ-1001-31
   39| Front Panel| 1| HZ-1001-34
   40| RISE ABOVE Logo Plate| 1| HZ-1001-35
   45| M6 x 14 mm Screw| 10| HZ-1001-40

9. Attach the casters using M12 caster wrench. Mount locking casters to front legs and mount swivel casters to rear legs.
   NOTE: You can lock the casters that have locks, allowing you to assemble the caster without using a caster wrench.

10. Turn the fire chamber and lid assembly on its back, then rotate the lighting instruction tag outward. Turn the battery cap counterclockwise to insert (1) AA battery. Attach 4-foot brackets using 8-M6 x 14 mm screws.
    ITEM| PART DESCRIPTION| QTY| PART #
    ---|---|---|---
    18| Adjustable Foot| 4| HZ-1004-16
    18A| Foot Bracket| 4| HZ-1004-16A
    23| Electronic Igniter Module w/ 4 Outlets| 1| HZ-1001-19
    45| M6 x 14 mm Screw| 8| HZ-1001-40

11. Turn the cart right side up. Attach fire chamber assembly to the “X” frame using 4-1/4″-20 x 15 mm knob with threaded shaft.
    NOTE: We recommend the help of a friend to attach the upper section of the cooking chamber to the “X” cart frame due to the size and weight of the fire chamber assembly.

NOTE: We recommend the help of a friend to attach the upper section of the cooking chamber to the “X” cart frame due to the size and weight of the fire chamber assembly.

12. Install control knobs and insert leveler into housing.**
    ITEM| PART DESCRIPTION| QTY.| PART #**
    ---|---|---|---
    20| Control Knob-Common| 4| HZ-1004-38
    26| Leveler| 1| HZ-1007-21

13. Attach lid handle assembly using 2-M6 x 14 mm screws.
    ITEM| PART DESCRIPTION| QTY| PART #
    ---|---|---|---
    2| Lid Handle Assembly| 1| HZ-1001-02
    3| Lid Handle Standoff-Bezel| 2| HZ-1001-03
    45| M6 x 14 mm Screw| 2| HZ-1001-40

14. Install griddle plate onto the fire chamber using 2-“JJ” hook handles.**
    ITEM| PART DESCRIPTION| QTY.| PART #**
    ---|---|---|---
    5| Griddle Plate| 1| HZ-1001-05
    6| JJ Hook Handle-L & R| 2| HZ-1001-06

15. Install left and right side table brackets using 8-M6 x 14 mm screws. Install left and right side tables using 8-M6 x 7H shoulder screws.
    ITEM| PART DESCRIPTION| QTY.| PART #
    ---|---|---|---
    6| JJ Hook Handle-L & R| 2| HZ-1001-06
    11| Bracket-Side Table-A| 2| HZ-1001-10
    12| Bracket-Side Table-B| 2| HZ-1001-11
    13| Side Table-Right| 1| HZ-1001-12
    14| Side Table-Left| 1| HZ-1001-13
    45| M6 x 14 mm Screw| 8| HZ-1001-40
    49| M6 x 7H Shoulder Screw| 8| HZ-1001-44

16. Install grease cup and cover.**
    ITEM| PART DESCRIPTION| QTY.| PART #**
    ---|---|---|---
    29| Grease Cup with Cover| 1| HZ-1001-22

17. Install swing away warming rack following steps 1-4.
    ITEM| PART DESCRIPTION| QTY.| PART #
    ---|---|---|---
    52| Warming Rack| 1| HZ-1001-47

ASSEMBLED DIMENSIONS

Quick link
REGISTER YOUR ELITE 48 PRODUCT ASSEMBLY VIDEOS RECIPES + more

https://halo-pg.com/

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>