HALO HZ-1002-XNA 3-Burner Propane Griddle User Guide
- June 10, 2024
- HALO
Table of Contents
ELITES
3-BURNER 6-ZONE
OUTDOOR Propane GRIDDLE
User Guide
HZ-1002-XNA 3-Burner Propane Griddle
WARNING
The manufacturer has made every effort to eliminate any sharp edges. However,
you should handle all components with care to avoid accidental injury.
NOTICE: Before assembly, make sure all parts are present. If any part is
missing or damaged, do not attempt to assemble the appliance. Contact customer
service for replacement parts at
1-833-572-1688.
NEED MORE INSTRUCTIONS?
Scan for registration, assembly videos, care + use, warranty, recipes, + more.
BATTERY NOT INCLUDED. Requires 1 AA battery for igniter.
IMPORTANT: Please read all instructions thoroughly before proceeding.
Find a large, clean area in which to assemble your HALO Elite3B Outdoor
Griddle. Please refer to the assembly diagram, as necessary.
- Install left outer leg using 3-M6 x 14 mm screws. Install leg cap.
NOTICE: Make sure all the plastic protection is removed before assembling.
Tool required for assembly: #2 Phillips Screwdriver
| ITEM | PART DESCRIPTION | QTY. | PART # |
|---|---|---|---|
| 31 | Cap-Leg | 1 | HZ-1001-48 |
| 32 | Left-Outer Leg-Long | 1 | HZ-1001-49 |
| 32A | Left-Outer Leg-Short | 1 | HZ-1001-50 |
| 46 | M6 x 14 mm Screw | 3 | HZ-1001-40 |
- Install left inner leg using 3-M6 x 14 mm screws. Install leg cap.
ITEM| PART DESCRIPTION| QTY.| PART #
---|---|---|---
31| Cap-Leg| 1| HZ-1001-48
33| Left-Inner Leg-Long| 1| HZ-1001-51
33A| Left-Inner Leg-Short| 1| HZ-1001-52
46| M6 x 14 mm Screw| 3| HZ-1001-40
- Install left outer leg assembly and right inner Leg assembly using pivot bracket 41 and 41A, 2-M6 x 3H Shoulder screws, M6 x 93 mm knob with threaded shaft and nylon spacer. Tighten screws firmly. Set assembly aside.
ITEM| PART DESCRIPTION| QTY| PART #
---|---|---|---
41| Pivot Bracket-A| 1| HZ-1001-36
41A| Pivot Bracket-B| 1| HZ-1001-37
47| M6 x 93 mm Knob with Threaded Shaft| 1| HZ-1001-41
49| M6 x 3H Shoulder Screw| 2| HZ-1001-43
51| Nylon Spacer| 1| HZ-1001-45
- Install right inner leg assembly using 3-M6 x 14 mm screws. Install leg cap.
ITEM| PART DESCRIPTION| QTY.| PART #
---|---|---|---
31| Cap-Leg| 1| HZ-1001-48
34| Right-Inner Leg-Long| 1| HZ-1001-53
34A| Right-Inner Leg-Short| 1| HZ-1001-54
46| M6 x 14 mm Screw| 3| HZ-1001-40
- Install right outer leg assembly using 3-M6 x 14 mm screws. Install leg cap.
ITEM| PART DESCRIPTION| QTY.| PART #
---|---|---|---
31| Cap-Leg| 1| HZ-1001-48
35| Right-Outer Leg-Long| 1| HZ-1001-55
35A| Right-Outer Leg-Short| 1| HZ-1001-56
46| M6 x 14 mm Screw| 3| HZ-1001-40
- Install right outer leg assembly and right inner leg assembly using pivot bracket 42 and 41A, 2-M6 x 3H shoulder screws, M6 x 93 mm knob with threaded shaft and nylon spacer. Tighten screws firmly. Set assembly aside.
ITEM| PART DESCRIPTION| QTY.| PART #
---|---|---|---
41A| Pivot Bracket-B| 1| HZ-1001-37
42| Pivot Bracket-C| 1| HZ-1001-38
47| M6 x 93 mm Knob with Threaded Shaft| 1| HZ-1001-41
49| M6 x 3H Shoulder Screw| 2| HZ-1001-43
51| Nylon Spacer| 1| HZ-1001-45
- Install tank retention support bracket and rear brace using 2-M6 x 14 mm screws.
ITEM| PART DESCRIPTION| QTY.| PART #
---|---|---|---
37| Tank Support Bracket| 1| HZ-1001-32
38| Rear Brace| 1| HZ-1002-11
46| M6 x 14 mm Screw| 2| HZ-1001-40
- Install tank retention wire, front panel and rear brace assembly using 10-M6 x 14 mm screws.
Tighten screws firmly.
IMPORTANT: Do not tighten screws completely until all screws for this step have been installed. ITEM| PART DESCRIPTION| QTY.| **PART**
---|---|---|---
37| Tank Support Bracket| 1| HZ-1001-32
38| Rear Brace| 1| HZ-1002-11
46| M6 x 14 mm Screw| 10| HZ-1001-40
39| Front Panel| 1| HZ-1002-12
40| RISE ABOVE Logo Plate| 1| HZ-1004-39
36| Tank Retention Wire| 1| HZ-1002-10
- Attach the casters using M12 caster wrench.
Mount locking casters to front legs and mount swivel casters to rear legs.
NOTE: You can lock the casters that have locks, allowing you to assemble the caster without using a caster wrench.
| ITEM | PART DESCRIPTION | QTY. | ART # |
|---|---|---|---|
| 43 | Caster with Lock | 2 | HO-1006-XNA-13 |
| 44 | Caster-Swivel | 2 | HO-1006-XNA-12 |
- Turn the fire chamber and lid assembly on its back, then rotate the lighting instruction tag outward. Turn the battery cap counterclockwise to insert (1) AA battery. Attach 4-foot brackets using 8-M6 x 14 mm screws.
ITEM| PART DESCRIPTION| QTY.| PART #
---|---|---|---
18A| Foot Bracket| 4| HZ-1001-16A
18| Adjustable Foot| 4| HZ-1001-16
46| M6 x 14 mm Screw| 8| HZ-1001-40
- Turn the cart right side up. Attach fire chamber assembly to the “X” frame using 4-1/4″-20 x 15 mm knob with threaded shaft.
NOTE: We recommend the help of a friend to attach the upper section of the cooking chamber to the “X” cart frame due to the size and weight of the fire chamber assembly.
| ITEM | PART DESCRIPTION | QTY. | PART # |
|---|---|---|---|
| 48 | 1/4″-20 x 15mm Knob with Threaded Shaft | 4 | HZ-1001-42A |
-
Continued from page 13.
NOTE: We recommend the help of a friend to attach the upper section of the cooking chamber to the “X” cart frame due to the size and weight of the fire chamber assembly.
-
Install control knobs and insert leveler into housing.
ITEM| PART DESCRIPTION| QTY.| PART #
---|---|---|---
20| Control Knob-Common| 3| HZ-1004-38
26| Leveler| 1| HZ-1007-21
- Attach lid handle assembly using 2-M6 x 14 mm screws and 2-Lid Handle standoff bezels.
ITEM| PART DESCRIPTION| QTY.| PART #
---|---|---|---
2| Lid Handle Assembly| 1| HS-1005-2
2A| Lid Handle Standoff-Bezel| 2| HZ-1001-03
46| M6 x 14 mm Screw| 2| HZ-1001-40
- Install griddle plate onto the fire chamber using 2-“JJ” hook handles.
ITEM| PART DESCRIPTION| QTY.| PART #
---|---|---|---
4| Griddle Plate| 1| HZ-1002-02
5| JJ Hook Handle-L & R| 2| HZ-1001-06
- Install left and right side table brackets using 8-M6 x 14 mm screws. Install left and right side tables using 8-M6 x 7H shoulder screws. Insert “JJ” hook handles on side tables.
ITEM| PART DESCRIPTION| QTY.| PART #
---|---|---|---
5| JJ Hook Handle-L & R| 2| HZ-1001-06
11| Bracket-Side Table-A| 2| HZ-1001-10
12| Bracket-Side Table-B| 2| HZ-1001-11
13| Side Table-Right| 1| HZ-1001-12
14| Side Table-Left| 1| HZ-1001-13
46| M6 x 14 mm Screw| 8| HZ-1001-40
50| M6 x 7H Shoulder Screw| 8| HZ-1001-44
- Install grease cup and cover.
ITEM| PART DESCRIPTION| QTY.| PART #
---|---|---|---
29| Grease Cup with Cover| 1| HZ-1001-21
- Install swing away warming rack following steps 1-4.
ITEM| PART DESCRIPTION| QTY.| PART #
---|---|---|---
45| Swing Away Warming Rack with support wire| 1| HZ-1002-13
ASSEMBLED DIMENSIONS
Quick link ►
REGISTER YOUR ELITE3B
PRODUCT ASSEMBLY VIDEOS
RECIPES + more https://halo-pg.com/
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>