GE 71241 19L 11 Inch Silver Glittered Snowflake Tree Top Instructions
- June 10, 2024
- GE
Table of Contents
71241 19L 11 Inch Silver Glittered Snowflake Tree Top
Instructions
IMPORTANT SAFETY INSTRUCTIONS
When using electric products, basic precautions should always be followed
including the follow in
a) READ AND FOLLOW ALL SAFETY INSTRUCTION
b) Do not use seasonal products outdoors unless marked suitable for indoor and
outdoor use. When products are used in outdoor applications, connect the
product to a Ground Fault Circuit Interrupting (GFCI) outlet If one is not
provided, contact a qualified electrician for proper installation.
c. This seasonal use product is not intended for permanent installation or
use.
d) Do not mount or place near gas or electric heater, fireplaces, candles or
other similar sources of heat.
e) Do not secure the wiring of the product with staples or nails, or place on
sharp hooks or nails.
f) Do not let the lamps rest on the supply cord or on any wire.
g) Unplug the product when leaving the house, when retiring for the night, or
if left unattended.
h) This is an electric product-not a toy! To avoid risk of fire, burns,
personal injury and electric shock, it should not be played with or placed
where small children can reach it.
i) Do not use this product for other than its intended use.
j) Do not hang ornaments or other objects from cord, wire, or light string.
k) Do not place lighting string on carpeting, drapes, furniture, or allow it
to contact vinyl siding while the power is on.
l) Do not perform any maintenance or troubleshoot for bad or broken lamps
while the power is on.
m) Do not close doors or windows on the product or extension cords as this may
damage the wire insulation.
n) Do not cover the product with cloth, paper, or any material not part of the
product when in use.
o) This product is equipped with push-in type lamps. Do not twist lamps.
p)This product employs overload protection (fuse). A blown fuse indicates an
overload or short -circuit situation. If the fuse blows, unplug the product.
Replace the fuse as per the user servicing instructions(follow product marking
for proper fuse rating) and check the product. If the replacement fuse blows,
a short-circuit may be present and the product should be discarded.
Read and follow all instructions that are on the roduct or provided with the
product.
SAVE THESE INSTRUCTION
USE AND CARE INSTRUCTIONS
a) When the product is placed on a live tree, the tree should be well
maintained and fresh. Do not place on live trees in which the needles are
brown or break off easily. Keep the tree holder filled with water.
b) If the product is placed on a tree, the tree should be well secured and
stable.
c) Before using or reusing, inspect product carefully. Discard any products
that have cut, damaged, or frayed wire insulation or cords, cracks in the lamp
holders or enclosures, loose connections, or exposed copper wire.
d) When storing the product, carefully remove the product from wherever it is
placed, including trees, branches, or bushes, to avoid any undue strain or
stress on the product conductors, connections, and wires.
e) When not in use, store neatly in a cool, dry location protected from
sunlight.
USER SERVICING INSTRUCTIONS
Fuse replacement: Most often, fuses blow because too many sets have been
strung end-to-end.
A) Before changing fuses, make sure the set is unplugged.
b) Grasp plug and remove from the receptacle or other outlet device. Do not
unplug by pulling on cord.
c) Using a flathead screwdriver, open fuse cover. Slide open the fuse access
cover on top of attachment plug towards blades.
d) Remove fuses carefully. e) Risk of fire. Replace fuse only with 3 Amp, 125
Volt fuse (provided with product).
f) Close fuse cover. Slide closed the fuse access cover on top of the
attachment plug. Make sure door is fully closed and fuses are completely
covered.
g) Risk of fire. Do not replace attachment plug. Contains a safety
device(fuse) that should not be removed. Discard product if the attachment
plug is damaged.
Bulb replacement: Before changing bulbs, make sure set is unplugged.
Step 1: Grasp plug and remove from the receptacle or other outlet device.
Do not unplug by pulling cord.
Step 2: Hold bulb by the plastic base and pull bulb base straight out of
socket.
Step 3: Replace lamp with only 7 Vol, 0.98 Wall super brightness midget
push-in type lamp provided with product.
Push spare bulb base assembly into socket. Do not twist bulb when insight into
socket. If bulbs are twisted, part of the set will not light.
If the spare bulbs provided with the product have no plastic base or the
plastic base does not fit, first follow steps 1-2 above. Then:
a) Remove the old bulb by straightening the bulb wires and pulling bulbs
straight from the base.
b) Replace the new bulb by straightening the bulb leads and aiming each wire
into a separate hole in the plastic base.
c) Make sure each bulb lead comes out an exit opening at the bottom of the
plastic base. Now bend each lead up such that each bulb lead fits closely
against the narrow side of the plastic base.
CAUTION:
1. This lighting string is rated 16.8 Walls ( 0.14 Amps), do not overload.
2. To reduce the risk of overheating, replace burned out lamps promptly. Use
7 Volt , 0.98 Watt lamps only.
3. To reduce the risk of fire and electric shock:
a)Do not install on trees having needles, leaves or branch coverings of metal
or materials that look like metal, and
b)Do not mount or support strings in a manner that can cut or damage wire
insulation.
For questions and/or assistance, call customer service at
1-877-398-7337 or visit us on the
web at www.GEholidaylighting.com.
FOR INDOOR USE ONLY
PRINTED IN CHINA
120 VOLTS
E246482 HC-22
MADE IN CHINA
©2022 Nicolas Holiday Limited, 9F.,
No. 37, Guangfu N. Rd Taipei,
Taiwan 10560.
All rights reserved.
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>