ELKO Smart Smoke Alarm Battery User Guide
- June 10, 2024
- ELKO
Table of Contents
ELKO Smart Smoke Alarm Battery
Device user guide
This guide provides information about the features and functionality of the ELKO Smart Smoke Alarm Battery.
About the device
The ELKO Smart Smoke Alarm Battery is a wireless smoke detector that operates on a battery. It is designed to detect smoke and provide an audible alert to warn occupants of a potential fire.
The device is equipped with a Smart function that allows it to be paired with a compatible smartphone app, providing remote access to the device and alerts.
Installing the device
Before installing the device, read the safety instructions carefully to avoid potential hazards or personal injury. The device should be installed in accordance with the instructions provided in the user guide.
The device can be easily installed on a ceiling or wall using screws or adhesive tape. Ensure that the device is mounted at least 30 centimeters away from any wall or corner and that it is not obstructed by any object.
Pairing the device
To pair the device with a compatible smartphone app, follow these steps:
- Download and install the ELKO Smart app from the App Store or Google Play Store.
- Ensure that your smartphone is connected to a Wi-Fi network.
- Open the ELKO Smart app and follow the instructions to create an account and set up the device.
- Press and hold the test button on the device until it beeps andthe LED light flashes.
- The device will now appear in the app and can be accessed remotely.
Safety information
It is important to read the safety instructions carefully before installing, operating, servicing, or maintaining the device to avoid potential hazards or personal injury.
The device is equipped with safety labels that indicate potential electrical hazards. Obey all safety messages to avoid possible injury or death.
Legal Information
The ELKO brand and any trademarks of ELKO AS and its subsidiaries referred to in this guide are the property of ELKO AS or its subsidiaries. All other brands may be trademarks of their respective owners.
This guide and its content are protected under applicable copyright laws and furnished for informational use only. No part of this guide may be reproduced or transmitted in any form or by any means (electronic, mechanical, photocopying, recording, or otherwise), for any purpose, without the prior written permission of ELKO.
ELKO products and equipment should be installed, operated, serviced, and maintained only by qualified personnel.
As standards, specifications, and designs change from time to time, information contained in this guide may be subject to change without notice.
To the extent permitted by applicable law, no responsibility or liability is assumed by ELKO and its subsidiaries for any errors or omissions in the informational content of this material or consequences arising out of or resulting from the use of the information contained herein.
ELKO – Smart Smoke Alarm Battery
Device user guide
Information about features and functionality of the devices 11/2022
www.elko.no
Legal Information
The ELKO brand and any trademarks of ELKO AS and its subsidiaries referred to
in this guide are the property of ELKO AS or its subsidiaries. All other
brands may be trademarks of their respective owners.
This guide and its content are protected under applicable copyright laws and
furnished for informational use only. No part of this guide may be reproduced
or transmitted in any form or by any means (electronic, mechanical,
photocopying, recording, or otherwise), for any purpose, without the prior
written permission of ELKO.
ELKO does not grant any right or license for commercial use of the guide or
its content, except for a non-exclusive and personal license to consult it on
an "as is" basis. ELKO products and equipment should be installed,
operated, serviced, and maintained only by qualified personnel.
As standards, specifications, and designs change from time to time,
information contained in this guide may be subject to change without notice.
To the extent permitted by applicable law, no responsibility or liability is
assumed by ELKO and its subsidiaries for any errors or omissions in the
informational content of this material or consequences arising out of or
resulting from the use of the information contained herein.
Safety information……………………………………………………………………………4 ELKO – Smart Smoke Alarm
Battery………………………………………………..5
For your safety ……………………………………………………………………………….5 About the
device……………………………………………………………………………..5 Installing the device
…………………………………………………………………………7 Pairing the device
……………………………………………………………………………7
Pairing device manually……………………………………………………………….7 Pairing device with auto
scan………………………………………………………..9 Setting up connection without ELKO system
………………………………………….9 Interconnecting devices without ELKO SmartHUB……………………………..9
Disconnecting a slave device ………………………………………………………10 Testing the
device…………………………………………………………………………. 11 Testing the individual device
………………………………………………………. 11 Testing the interconnected device(s)
…………………………………………….12 Configuring the device ……………………………………………………………………12
Changing the device icon …………………………………………………………..12 Renaming the device
………………………………………………………………..13 Changing the device location
………………………………………………………13 Removing the device from the app
…………………………………………………….14 Resetting the device manually
………………………………………………………….14 Using the device……………………………………………………………………………15
Checking the device history ………………………………………………………..15 Setting LED
brightness………………………………………………………………16 Test alarm reminder
………………………………………………………………….17 Silencing the device ………………………………………………………………….18
Snoozing the device alerts………………………………………………………….19 False alarm
…………………………………………………………………………….19 Creating an automation
……………………………………………………………..20 Maintenance and
cleaning……………………………………………………………….25 LED Indications
…………………………………………………………………………….26 Troubleshooting ………………..
………………………………………………………….27 Technical Data ……………………………………………………………………………..27
DUG_Smart Smoke Alarm DC_ELKO-01
3
Safety information
Safety information
Important information
Read these instructions carefully and look at the equipment to become familiar
with the device before trying to install, operate, service, or maintain it.
The following special messages may appear throughout this manual or on the
equipment to warn of potential hazards or to call attention to information
that clarifies or simplifies a procedure.
The addition of either symbol to a “Danger” or “Warning” safety label
indicates that an electrical hazard exists which will result in personal
injury if the instructions are not followed.
This is the safety alert symbol. It is used to alert you to potential personal
injury hazards. Obey all safety messages that accompany this symbol to avoid
possible injury or death.
DANGER
DANGER indicates a hazardous situation which, if not avoided, will result in
death or serious injury. Failure to follow these instructions will result in
death or serious injury.
WARNING
WARNING indicates a hazardous situation which, if not avoided, could result in
death or serious injury.
CAUTION
CAUTION indicates a hazardous situation which, if not avoided, could result in
minor or moderate injury.
NOTICE
NOTICE is used to address practices not related to physical injury.
4
DUG_Smart Smoke Alarm DC_ELKO-01
ELKO – Smart Smoke Alarm Battery
ELKO – Smart Smoke Alarm Battery
EKO09761
For your safety NOTICE
EQUIPMENT INSTALLATION HAZARD · Always operate the product in compliance with
the specified technical data. · Keep the installation instruction for the life
of the product. Failure to follow these instructions can result in equipment
damage.
WARNING
SEALED BATTERY HAZARD Do not recharge, disassemble or incinerate the battery.
Failure to follow these instructions can result in death, serious injury, or
equipment damage.
About the device
The Smart Smoke Alarm Battery (device) uses a photoelectric sensor to detect
smoke generated by fire. It also includes a temperature sensor that detects
heat caused by rapid increase in temperature. When connected to the ELKO
system the device sends the notifications via the ELKO app.
DUG_Smart Smoke Alarm DC_ELKO-01
5
ELKO – Smart Smoke Alarm Battery
Operating elements
A. Status LED (Amber, Green and Red LED) B. Standby LED (Red LED) C. Test/Hush
button D. Power switch E. Setup/Reset button
A E
DO NOT PAINT PUSH TO TEST / HUSH
OFF/AUTO
D
ON
OFF/AUTO ON
B
C
Installation location
· Smoke Alarm can be installed on a flat/inclined ceiling, or on the wall. · Do not install smoke alarms near windows, doors, or ducts. · Avoid paint, stickers, or other decorations.
1 m
M
0.3 m
0.3 m min.
12 m
0.5 m min. / 1.5 m max.
= =
6
DUG_Smart Smoke Alarm DC_ELKO-01
ELKO – Smart Smoke Alarm Battery
Installing the device
Refer to the installation instruction supplied with this product. See Smart
Smoke Alarm Battery.
Pairing the device
Using the ELKO app, pair your device with the ELKO SmartHUB to access and
control the device. You can either add the device manually or do an auto-scan
to pair it.
IMPORTANT: Do not mount the device before the pairing. The Setup/Reset button
(Zigbee) and power switch are located on the rear side of the device. NOTE:
When multiple smoke alarms are paired with same ELKO SmartHUB, an 868MHz radio
frequency (RF) interconnection is automatically created between smoke alarms.
Pairing device manually
To pair devices manually:
1. Locate the power switch on the rear side of the device. Use a screwdriver
to turn the power switch to ON position.
OFF/AUTO
ON
OFF/AUTO ON
NOTE: When mounted on wall or the ceiling, the device is automatically turned
ON. 2. In ELKO Smart app Home page, tap +.
3. Tap and select the required ELKO SmartHUB on the slide-up menu. 4. Select
any one of the options to add device (A):
Add Device with Install Code Add Device without Install Code
Add Device
Install Code is Recommended
Add Device without Install Code
A
DUG_Smart Smoke Alarm DC_ELKO-01
7
ELKO – Smart Smoke Alarm Battery 5. To pair the device with an install code,,
tap Add Device with Install Code to
display the slide-up menu. Select any one of the options (B): Scan Install
Code – You can scan the device for the an install code. Enter Install Code
Manually – You can manually enter the install code
from the device After pairing the device with an install code, proceed to Step
7.
Add Device
Install Code is Recommended
Add Device without Install Code
B
TIP: It is highly recommended to pair the device with Install code. 6. To pair the device without install code, tap Add Device without Install Code. 7. Once the device is On, press Set/Reset button 3 times.
OFF/AUTO
3× < 2 s
ON
The LED blinks yellow.
8. In the app, select LED is blinking yellow and tap Start Configuration (C).
Cancel
How to pair device 1. Turn the Power switch located at the rear
side of the device to ON position. Note: Use a screwdriver to turn the switch.
2. Tap Set/Reset button for 3 times.
DO NOT PAINT PUSH TO TEST / HUSH
OFF/AUTO ON
LED is blinking yellow
C
9. After a few seconds, a solid green LED indicates that the device has been
successfully paired.
DO NOT PAINT
PUSH TO TEST / HUSH
10. Once the device is paired in the app, tap Done.
8
DUG_Smart Smoke Alarm DC_ELKO-01
ELKO – Smart Smoke Alarm Battery
Pairing device with auto scan
Pairing the device with auto scan automatically discovers the device when the
corresponding device is powered on. Follow the steps to pair the device:
1. Locate the power switch on the rear side of the device. Use a screwdriver
to turn the power switch to ON position.
2. On the Home page, tap +. 3. Tap Auto scan and than tap Confirm. 4. If you
have multiple hubs, do Step 4 or proceed to Step 5. 5. Tap Select hub and
select an ELKO SmartHUB from the slide-up menu. 6. Press the Set/Reset button
3 times within 2 s.
NOTE: · The LED blinks yellow. · Wait for a few seconds until the device
search is complete.
TIP: If you want to pair multiple devices at once, perform step 5 on each
device and wait for a few seconds for them to be detected. 7. Select Smoke
Alarm and tap Next (A).
Auto Scan
Available devices found
Smoke Alarm
Next
A
8. Once the device is added successfully, tap Done.
Setting up connection without ELKO system
Interconnecting devices without ELKO SmartHUB
The smoke alarms (devices) can be connected directly to each other via RF
connections even without a ELKO SmartHUB network.
IMPORTANT: Turn the power switch to ON position on all the devices. 1.
Identify a device and mark it as Master with a label supplied. Other devices
are considered as Slave.
DUG_Smart Smoke Alarm DC_ELKO-01
9
ELKO – Smart Smoke Alarm Battery 2. Short press the Test/Hush button 3 times within 2 s on the primary device.
3× < 2 s
The Standby LED turns on for 30 s once it is in pairing mode. 3. Identify a
Slave device and short press the Test/Hush button 3 times within 2
s. The Standby LED blinks 3 times on both Master and devices indicating a
successful RF connection. Than on the Master device, the Standby LED again
turns on for 30 s
3× < 2 s
Repeat the step 3 on all Slave devices. NOTE: To exit from pairing mode, short
press (< 0,5 s) the Test/Hush button 3 times on the Master device. The Standby
LED turns off indicating that the Master device is not in pairing mode.
Disconnecting a slave device
Remove a Slave device from the mounting base (See “Removing a device from the
mounting base in the instruction manual”).
NOTE: · Do not remove the Master device. · Read the following steps before
disconnecting a Slave device.
1. Make sure that the power switch is in OFF/AUTO position.
OFF/AUTO
ON
OFF/AUTO ON
2. Press and hold the Test/Hush button and simultaneously turn the power switch to ON position.
OFF/AUTO
+ ON
OFF/AUTO ON
….3 s
The Standby LED turns on for 3 s.
10
DUG_Smart Smoke Alarm DC_ELKO-01
ELKO – Smart Smoke Alarm Battery
3. Continue to hold the Test/Hush button until the Standby LED turns off.
Then release the Test/Hush button.
4. Short press the Test/Hush button when the Standby LED is on for 3 s.
1× < 5 s
The Standby LED blinks for 5 s indicating disconnecting of RF interconnection
also the Status LED blinks green for 7 times.
IMPORTANT: When the Slave device is successfully disconnected, make sure to
turn the power switch to OFF/ AUTO position.
Testing the device
The device has a test mode that helps ensure the proper operation of the
device. It is recommended to test the device once a month. If the device is
installed in a mobile home, it is recommended to test the device weekly and
before every journey.
NOTE: Using ELKO Smart app you can set the monthly reminder for test alarm in
settings, page 17.
Testing the individual device
IMPORTANT: · Test the device once a month to ensure proper operation. · If the
smoke alarm is installed in a mobile home, test weekly and before every
journey.
Press the Test/Hush button on each device for more than 3 s until an alarm
goes off. If the alarm does not go off, either the battery is low or there may
be other technical issues. Refer troubleshooting smoke alarm battery, page 27.
DUG_Smart Smoke Alarm DC_ELKO-01
11
ELKO – Smart Smoke Alarm Battery
Testing the interconnected device(s)
It is possible to test all the devices simultaneously in an interconnected
network with one operation.
1. Select any interconnected device. 2. Press and hold the Test/Hush button
for more than 10 s until an alarm goes
off on all interconnected devices.
DO NOT PAINT
PUSH TO TEST / HU
1× > 10 s
3. If there is no alarm triggered on the interconnected devices, check if the
distance between each device is within the specification. Also check that the
device is On and working properly. Refer troubleshooting smoke alarm battery,
page 27.
Configuring the device
Changing the device icon
You can change the device icon using the ELKO Smart app. 1. On the Home page,
select the device for which you wish to change the icon.
2. At the top-right corner of the screen, tap .
3. Tap edit next to the device name. 4. Tap Icon to view the menu. 5. In the
slide-up menu, select any one of the following (A) to change the device
icon: Take photo – allows you to click a photo from the mobile camera.
Select from Icon Library – allows you to select an icon from the app
library. Select from Album – allows you to select a photo from the mobile
gallery.
12
DUG_Smart Smoke Alarm DC_ELKO-01
ELKO – Smart Smoke Alarm Battery
Renaming the device
You can rename the device using the ELKO Smart app. 1. On the Home page,
select the device for which you wish to rename. 2. At the top-right corner of
the screen, tap . 3. Tap edit next to the device name. 4. Tap Name, enter the
new name (A) and then tap Save.
Name
Rename Save
A
Changing the device location
You can change the device location using the ELKO Smart app. 1. On the Home page, select the device for which you wish to change the location.
2. At the top-right corner of the screen, tap .
3. Tap edit next to the device name. 4. Tap Location. 5. Select the desired location from the list (A) and then tap Save.
Device location
Save
Living Room Master Bedroom
Dining Room Study Room Kids Room
A
DUG_Smart Smoke Alarm DC_ELKO-01
13
Removing the device from the app
ELKO – Smart Smoke Alarm Battery
You can remove a device from the device list using the ELKO Smart app, To
remove the device:
1. On the Home page, tap All devices > Smoke Alarm.
2. Tap to display more details. 3. Tap Remove and Factory Reset Device (A) and tap Confirm.
More
Smoke Alarm
Room: Sensors Device information Moment and Automation
Others
FAQ & Feedback Add to home Screen
No updates available.
Remove and Factory Reset Device
A
TIP: Alternatively, you can tap and hold on theSmoke Alarm on the Home page to
remove the device. NOTE: By removing the device, you will reset the device. If
you still have a problem with the reset, then refer to resetting the device,
page 14.
Resetting the device manually
Short press (< 0,5 s) the Setup/Reset button 3 times and then long press the
Setup/Reset button once for >10 s to reset the device to factory default mode.
IMPORTANT: All configuration data, user data and network data are deleted.
14
DUG_Smart Smoke Alarm DC_ELKO-01
ELKO – Smart Smoke Alarm Battery
Using the device
The Control Panel of the smoke alarm allows you to view the current state of
the device and allow you access the history and settings. On the Home page,
tap All devices > Smoke Alarm to access the control panel. On the Smoke Alarm
control panel page, you can see the following:
· Battery level (A) · Current state of the device (B) · History, page 15 (C) ·
Settings (D) : LED brightness settings, page 16, Test alarm reminder, page
17.
A
Smoke Alarm
No Alarm
C D
History Settings
B
Checking the device history
Using the ELKO Smart app, you can monitor the smoke detection by accessing the
device history. To see the device history:
1. On the Home page, tap All devices > Smoke Alarm. 2. On the device control
panel page, tap History. 3. In the History page, you can see the date, time,
and type of alarm detected.
History
The history supports record checking for 7 days in maximum.
04 February
04 February Smoke Alarm
19:46:02 I The Smoke Alarm occured
Test Alarm 19:41:37 I The Test Alarm occured
Test Alarm 19:41:22 I The Test Alarm occured
NOTE: The history supports record checking for 7 days maximum.
DUG_Smart Smoke Alarm DC_ELKO-01
15
ELKO – Smart Smoke Alarm Battery
Setting LED brightness
You can change the LED brightness level between minimum and maximum manually
or by using ELKO app.
Changing the LED brightness manually
1. When the device is in standby mode, short press the test/hush button 3
times within 2 s.
3× < 2 s
2. When the Red LED is On, short press the Test/Hush button to switch between
Min. and Max. LED brightness.
1× < 0,5 s
3. Again short press the Test/Hush button 3 times within 2 s to store the
adjusted brightness level. Otherwise, you can wait 30s for the standby LED to
turn off, then the brightness level will be saved.
3× < 2 s
Changing the LED brightness using app
1. On the Home page, tap All devices > Smoke Alarm. 2. On the device control panel page, tap Settings. 3. Tap on LED Indicator Light Level (A). 4. Follow the settings mentioned in the pop-up notification, then tap Ok (B). 5. Select Min or Max indicator level (C).
Settings
A LED Indicator Light Level
Min
Test Alarm Reminder
Notice: you to take alarm test in every month if this function is on.
Settings
LED Indicator Light Level
Min
Test Alarm Reminder
Notice: you to take the alarm test in every month if this function is on.
Please press “Reset” key on the device to wake it up before applying the settings.
OFF/AUTO ON
Cancel
Ok
B
LED Indicator Light Level Min Max
Cancel
C
16
DUG_Smart Smoke Alarm DC_ELKO-01
ELKO – Smart Smoke Alarm Battery
Test alarm reminder
You can set the reminder for test alarm in the ELKO app. 1. On the Home page, tap All devices > Smoke Alarm. 2. On the device control panel page, tap Settings. 3. Tap the Test Alarm Reminder toggle switch (A) to turn on the reminder.
Settings
LED Indicator Light Level Test Alarm Reminder
Max
A
Notice: you to take the alarm test in every month if this function is on.
NOTE: The app will send a notification to remind you to take the alarm test in every month if this function is on.
DUG_Smart Smoke Alarm DC_ELKO-01
17
ELKO – Smart Smoke Alarm Battery
Silencing the device
Hush feature
During an alarm event, identify the device(s) which is/are blinking Red LEDs
then short press the Test/Hush button on the device to stop the alarm.
NOTE: In hush mode, the device will not detect smoke/high temperature for 10
minutes. After this time the device resumes to normal operation. During this
time, the Standby LED blinks once every 8 s. For instance, if smoke is
detected and the device is set to hush mode, hightemperature detection will
still be active. In the event that smoke and high temperature are both
detected at the same time, and the device is set to hush mode, then both smoke
and high temperature detection will not work for the next 10 minutes.
In an interconnected group, if more than one device has blinking Red LEDs and
an active alarm, short press the Test/Hush button on all devices. All
interconnected devices stop alarming within 5 to 10 s.
NOTE: Wait for 10 minutes before performing any test to avoid malfunctioning
of the device.
Once the device is set to Hush Mode the status can be checked in ELKO app.
Smoke Alarm
The device is in Hush Mode – it will not detect smoke temporarily.
Hush Mode
History Settings
18
DUG_Smart Smoke Alarm DC_ELKO-01
ELKO – Smart Smoke Alarm Battery
Temporarily disabling smoke detection
To temporarily disable the smoke detection of a device, short press the
Test/Hush button once when the device is in Standby mode. The device will not
detect smoke for 10 minutes. During this mode the Standby LED blinks once
every 8 s.
NOTE: The temperature sensor remains active even when the smoke detection is disabled.
Snoozing the device alerts
Low Battery
When the battery is low, the Standby LED blinks every 48 s, together with a
beep. You can snooze the low battery indication for 10 hours by short pressing
the Test/ Hush button once.
IMPORTANT: The user must replace the device within 30 days after the first
alert.
NOTE: You can always check the current battery level in the control panel.
Fault detection
When a device fault is detected, 2 beeps occur every 48 s together with blinking Standby LED. You can snooze the indication for 10 hours by short pressing the Test/Hush button once.
Alarm memory
In an interconnected group, the Standby LED on the triggered device blinks once every 2 s for 72 hours after the alarm has stopped. This allows the user to identify the device that was triggered by smoke/high temperature. Short press the Test/ Hush button once to snooze the blinking LED for 10 hours.
False alarm
In an event of a false alarm in an interconnected group, it is recommended to identify the triggering device(s). These devices must be cleaned, serviced or replaced if necessary.
DUG_Smart Smoke Alarm DC_ELKO-01
19
ELKO – Smart Smoke Alarm Battery
Creating an automation
Automation allows you to group multiple actions that are usually done
together, triggered automatically or at scheduled times. Using the ELKO Smart
app, you can create automations based on your needs. To create an automation:
1. On the Home page, tap the . 2. Go to Automation > + to create an
automation. 3. Tap Edit name, enter the name of the automation (A) and tap
Save.
TIP: You can choose the cover image that represents your automation by tapping
.
Cancel Automation settings Save
My Automation
A
Any condition is met Edit name
Add Condition
(0/10)
Action
(ASdadvede 0/80)
Add Task
All-Day
4. Tap Any condition is met to select any one of the condition type (B): All conditions are met- The automation is triggered when all the conditions are met. Any condition is met- The automation is triggered when at least one condition is met.
5. Tap Add Condition to display the slide-up menu.
20
DUG_Smart Smoke Alarm DC_ELKO-01
ELKO – Smart Smoke Alarm Battery
6. In the Add Condition menu, you can do either or all of the following
options (C): When weather changes – Select the various weather settings
Schedule – Set the time and day When device status changes – Select the
device and it’s function
NOTE: You can add one or more conditions using . .
Cancel Automation settings Save
My Automation
Any condition is met
(0/10)
Add Condition
Add Condition
C
7. Tap When device status changes > Smoke Alarm and select either or all of
the functions to add in the automation:
Heat Alarm – When the device detects rise in temperature (D) Test Mode –
When the device is in test mode (E) Remote Alarm – When the device is
triggered by interconnected device
(F) Hush Mode – When the device is in hush mode (G) Smoke Alarm – When the
device detects smoke (H)
Select function
D Heat Alarm E Test Mode F Remote Alarm G Hush Mode H Smoke Alarm
8. Tap Add task to display the slide-up menu.
DUG_Smart Smoke Alarm DC_ELKO-01
21
ELKO – Smart Smoke Alarm Battery
9. In the Add task menu, you can do either or all of the following options
(F): Run the device- Select the devices that you want to triggered. Moment
or Automation- Select the moment which you want to trigger or select the
automation that you want to enable or disable. Send notification- Turn On
notification for the automation. Delay – Set the delay time.
NOTE: You can add one or more actions using .
Cancel Automation settings Save
My Automation
Any condition is met
(0/10)
Add Condition
Action
(Added 0/80) Add task
Run the deAvdidceTask
Moment or Automation
All-Day
Delay
I
10. Tap on Effective period to set the time range for the automation. You can
select any one of the following (G):
All-day – 24 hours Daytime – From sunrise to sunset Night – From sunset
to sunrise Custom – User defined time period
All-day 24 hours
Daytime From sunrise to sunset
J
Night From sunset to sunrise
Custom
Next
Repeat City
Everyday
11. Once all the actions and conditions are set, tap Save. Once the automation is saved, it is visible on the Automation tab. You can tap the toggle switch on the automation to enable it.
22
DUG_Smart Smoke Alarm DC_ELKO-01
ELKO – Smart Smoke Alarm Battery
Example of an automation
This demonstration shows you how to create an automation to get notification
on your app when the smoke is detected.
1. Go to Automation > + to create an automation. 2. Tap Edit name, enter the
name of the automation and tap Save.
TIP: You can choose the cover image that represents your automation by tapping
. 3. Tap Add Condition > When device status changes > Smoke Alarm. 4. In
Select function menu tap on Smoke Alarm > Smoke Alarm (A).
Smoke Alarm
Smoke Alarm Ended
A Smoke Alarm
5. Tap Add task > Send Notification and select Notifications (B).
Multiple items selectable
Next
B
6. Tap Next.
DUG_Smart Smoke Alarm DC_ELKO-01
23
ELKO – Smart Smoke Alarm Battery
7. In the Automation Settings page, tap Save.
Cancel Automation settings Save
My Automation
Any condition is met
(1/10)
Smoke Alarm Smoke Alarm: Smoke Alarm
Action
(1/80) On
All-Day
Once the automation is saved, it is visible on the Automation tab. You can tap
the toggle switch on the automation to enable it.
Push notification will appear on the screen when the automation is triggered.
You can also tap on icon to access the notification history.
Editing an automation
To edit an automation: 1. On the Automation tab, locate the automation you
want to edit and tap . 2. On the Edit page, you can tap each item (such as
dimmer, shutter, delay, temperature, etc.) to change the settings. TIP: · You
can add one or more actions using . · To delete an existing condition or
action, slide each item towards left and tap Delete.
Deleting an automation
To delete an automation: 1. On the Automation tab, locate the automation that
you want to delete and then tap . 2. Tap Delete and tap Ok. NOTE: After
deleting an automation, the device action can no longer be triggered.
24
DUG_Smart Smoke Alarm DC_ELKO-01
ELKO – Smart Smoke Alarm Battery
Maintenance and cleaning
A monthly inspection is recommended to help ensure the device is dust, dirt,
and insect free. The device can be vacuumed (strongly recommended) or brushed
with a soft brush to remove accumulated dust, dirt or kitchen grease. Apply a
small amount of insect surface spray to a cloth and wipe around device(s)
every 3 to 6 months to mitigate insect ingress..
IMPORTANT: 1. Always test the device after cleaning, for more information
refer testing the device, page 11. 2. If necessary refer to the installation
instruction for more information about installing the device.
NOTICE
EQUIPMENT MAINTENANCE INSTRUCTIONS · Test the device regularly to ensure its
functionality and the battery is in good
condition. · Replace the device after 10 years from the date of manufacturing.
· Do not open the device casing or repair yourself. There are no serviceable
parts inside. Failure to follow these instructions can result in equipment
damage.
DUG_Smart Smoke Alarm DC_ELKO-01
25
LED Indications
Pairing
User Action Press the Setup/Reset button 3 times
ELKO – Smart Smoke Alarm Battery
LED Indication LED blinks yellow yellow, once per second.
Status
Pairing mode is active for 30 seconds. When pairing is completed, LED glows
green for some time before turning Off.
Resetting
User Action Press the Setup/Reset button 3 times and hold it for > 10 s.
LED Indication After 10 s, the LED starts blinking red.
Status
The device is in reset mode. It is reset to the factory settings after 10
seconds. The device then restarts and the LED starts blinking green before
turning Off.
Operating
Operating Mode
Normal mode / Standby mode
Alarm Mode
Local Alarm *
Interconnected alarm
Test mode
RF interconnection test
Hush mode Low battery mode
Fault mode
Snooze Mode
Low battery Fault Alarm memory
Standby LED Blinks every 48 s Blinks every 1 s OFF 1 blink every 1 s
OFF
Blinks every 8 s Blinks every 48 s
2 blinks every 48 s
Blinks every 24 s 2 blinks every 24 s Blinks every 48 s
Alarming Sound OFF 3 beeps every 4 s 3 beeps every 4 s 3 beeps every 4 s
Continuous 3 beeps every 4 s OFF 1 beep every 48 s
2 beeps every 48 s
OFF OFF OFF
Duration — — —
Until Test/Hush button is released 25 s
10 min End of life: replace smoke alarm Until fault has been cleared 10 hrs 10
hrs 10 hrs
NOTE: For all the operating modes, LED blinks Red. * For local smoke alarms, all red LEDs blink, whereas, for local temperature alarms, only the standby red LED blinks.
26
DUG_Smart Smoke Alarm DC_ELKO-01
ELKO – Smart Smoke Alarm Battery
Troubleshooting
Issue Device does not sound when tested
Device beeps and Standby LED blinks every 48 s Device beeps twice and Standby
LED blinks every 48 s Device produces alarm sound unexpectedly without smoke
or steam
Resolution/Action
1. Confirm that the power switch is in ON position, or the device is
installed correctly. If you are unsure then remove and reinstall the device.
2. Press Test/Hush button until an alarm sound is produced. Do not press
consecutively.
3. If the problem persists or if you have questions about the warranty,
contact customer care center.
Battery may be low or drained. Replace the device.
1. Clean the device. Refer to Maintenance section.
2. If the problem persists or if you have questions about the warranty,
contact customer care center.
1. Identify the triggered device, indicated by a blinking Standby LED and 3
beeps every 4 s.
2. Press Test/Hush button to pause the alarm sound. Interconnected device
stops alarming in 5 to 10 s.
3. Clean the device. Refer to Maintenance.
4. Reinstall the device and test.
5. If the problem persists or if you have questions about the warranty,
contact customer care center.
IMPORTANT: After an alarm event, the device that has blinking Standby LED
every 2 s is the triggered device. Identify the device and follow steps 3 to
5.
Technical Data
Battery Life Operating Current Sensing Type Operating Temperature Ambient
Humidity Interconnecting Communication protocol : Operating frequency
Wireless Range Horn Level Mounting Type Dimensions (H × W × D) Leisure
accommodation vehicles Standard Certification
10 years 70 mA Photoelectric. This alarm contains NO radioactive material. 0 °C to 45 °C 5% to 95% RF, max. 40 devices in one network Zigbee, max. 40 devices in one network Zigbee: 2405 – 2480 MHz RF: 868 MHz 40m indoor line of sight 85 dB at 3 m Mounting on ceiling and wall only 89 × 89 × 33.5 mm Yes EN 14604 Zigbee 3.0
DUG_Smart Smoke Alarm DC_ELKO-01
27
Trademarks
This guide makes reference to system and brand names that are trademarks of
their relevant owners.
· Zigbee® is a registered trademark of the Connectivity Standards Alliance. ·
Apple® and App Store® are brand names or registered trademarks of Apple Inc. ·
Google PlayTM Store and AndroidTM are brand names or registered trademarks
of Google Inc. · Wi-Fi® is a registered trademark of Wi-Fi Alliance®. Other
brands and registered trademarks are the property of their respective owners.
ELKO AS Sandstuveien 68, 0680 Oslo Pb 6598 Etterstad, 0607 Oslo Norway +47 67
79 39 00 support@elko.no
www.elko.no
As standards, specifications, and design change from time to time, please ask
for confirmation of the information given in this publication.
© 2022 ELKO AS. All rights reserved. DUG_Smart Smoke Alarm DC_ELKO-01
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>