DrayTek Vigor2762 VDSL2 Modem Router User Guide

DrayTek Vigor2762 VDSL2 Modem Router

• Version: 1.5
  • Firmware Version: V3.9.6.4 (For future update, please visit the DrayTek website)
• Date: June 28, 2022

Intellectual Property Rights (IPR) Information

• Copyrights © All rights reserved. This publication contains information that is protected by copyright. No part may be reproduced, transmitted, transcribed, stored in a retrieval system, or translated into any language without written permission from the copyright holders.
  Trademarks The following trademarks are used in this document:

  • Microsoft is a registered trademark of Microsoft Corp.
  • Windows, Windows 7, 8, 10, 11 and Explorer are trademarks of Microsoft Corp.
  • Apple and Mac OS are registered trademarks of Apple Inc.
  • Other products may be trademarks or registered trademarks of their respective manufacturers.

Safety Instructions and Approval

• Safety Instructions
  • Read the installation guide thoroughly before you set up the router.
  • The router is a complicated electronic unit that may be repaired only be authorized and qualified personnel. Do not try to open or repair the router yourself.
  • Do not place the router in a damp or humid place, e.g. a bathroom.
  • Do not stack the routers.
  • The router should be used in a sheltered area, within a temperature range of 0 to +40 Celsius.
  • Do not expose the router to direct sunlight or other heat sources. The housing and electronic components may be damaged by direct sunlight or heat sources.
  • Do not deploy the cable for LAN connection outdoor to prevent electronic shock hazards.
  • Keep the package out of reach of children.
  • When you want to dispose of the router, please follow local regulations on conservation of the environment. Warranty We warrant to the original end user (purchaser) that the router will be free from any defects in workmanship or materials for a period of two (2) years from the date of purchase from the dealer. Please keep your purchase receipt  in a safe place as it serves as proof of date of purchase. During the warrantyperiod, and upon proof of purchase, should the product have indications of failure due to faulty workmanship and/or materials, we will, at our discretion, repair or replace the defective products or components, without charge for either parts or labor, to whatever extent we deem necessary tore-store the product to proper operating condition. Any replacement will consist of a new or re-manufactured functionally equivalent product of equal value, and will be offered solely at our discretion. This warranty will not apply if the product is modified, misused, tampered with, damaged by an act of God, or subjected to abnormal working conditions. The warranty does not cover the bundled or licensed software of other vendors. Defects which do not significantly affect the usability of the product will not be covered by the warranty. We reserve the right to revise the manual and online documentation and to make changes from time to time in the contents hereof without obligation to notify any person of such revision or changes.

EU Declaration of Conformity

We DrayTek Corp. , office at No.26, Fushing Rd., Hukou, Hsinchu Industrial Park, Hsinchu 303, Taiwan, declare under our sole responsibility that the product

• Product name: ADSL2/2+ & VDSL2 Router
• Model number: Vigor2762
• Manufacturer: DrayTek Corp.
• Address: No.26, Fushing Rd., Hukou, Hsinchu Industrial Park, Hsinchu 303, Taiwan

is in conformity with the relevant Union harmonisation legislation: EMC Directive 2014/30/EU , Low Voltage Directive 2014/35/EU , ErP 2009/125/EC and RoHS 2011/65/EU with reference to the following standards

+A12:2011+ A2:2013

EC No. 1275/2008| 2008

• Hsinchu
  • (place)
• 22nd June, 2017
  • (date)
• Calvin Ma / President .
  • (Legal Signature)

FCC STATEMENT

Regulatory Information
Federal Communication Commission Interference Statement

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

1. This device may not cause harmful interference, and
2. This device may accept any interference received, including interference that may cause undesired operation.

Caution
Any changes or modifications not expressly approved by the grantee of this device could void the user’s authority to operate the equipment. More update, please visit www.draytek.com.

Package Content

Take a look at the package content. If there is anything missed or damaged, please contact DrayTek or dealer immediately.

The type of the power adapter depends on the country that the router will be installed. * The maximum power consumption is 17-23 Watt.

Panel Explanation

Vigor2762

Interface                Description

Factory Reset

| Restore the default settings.

Usage: Turn on the router (ACT LED is blinking). Press the hole and keep for more than 5 seconds. When you see the ACT LED begins to blink rapidly than usual, release the button. Then the router will restart with the factory default configuration.

USB1~USB2| Connector for a USB device (for 3G/4G USB Modem or printer).
GigaLAN1~LA N4| Connectors for local networked devices.
DSL| Connector for accessing the Internet.
I / O| Power Switch.
PWR| Connector for a power adapter.

Hardware Installation

This section will guide you to install the router through hardware connection and configure the router’s settings through web browser. Before starting to configure the router, you have to connect your devices correctly.

Network Connection

1. Connect the DSL interface to the land line jack with a DSL line cable.
2. Connect one port of 4-port switch to your computer with a RJ-45 cable. This device allows you to connect 4 PCs directly.
3. Connect one end of the power cord to the power port of this device. Connect the other end to the wall outlet of electricity.
4. Power on the router.
5. Check the ACT and DSL, LAN LEDs to assure network connection. (For the detailed information of LED status, please refer to section 1.1.)

Wall-Mounted Installation
Vigor2762 has keyhole type mounting slots on the underside.

1. A template is provided on the Vigor router packaging box to enable you to space the screws correctly on the wall.

2. Place the template on the wall and drill the holes according to the recommended instruction.

3. Fit screws into the wall using the appropriate type of wall plug.
   Note The recommended drill diameter shall be 6.5mm (1/4”).

4. When you finished about procedure, the router has been mounted on the wall firmly.

Software Configuration

To access Internet, please finish basic configuration after completing the hardware installation. The Quick Start Wizard is designed for you to easily set up your router for Internet access. You can directly access the Quick Start Wizard via Web Configurator. Make sure your PC connects to the router correctly.

Note You may either simply set up your computer to get IP dynamically from the router or set up the IP address of the computer to be the same subnet as the default IP address of Vigor router 192.168.1.1.

Open a web browser on your PC and enter http://192.168.1.1. A pop-up window will open to ask for a username and password. Please enter “admin/admin” as the Username/Password and click Login.

The Main Screen will pop up. Click Wizards>>Quick Start Wizard.

Note The home page will change slightly in accordance with the router you have.

The first screen of Quick Start Wizard is entering login password. After entering the password, please click Next.

On the next page, please select the WAN interface that you use. If DSL interface is used, please choose WAN1; if Ethernet interface is used, please choose WAN2; if 3G USB modem is used, please choose WAN3. Then click Next for next step. WAN1, WAN2 and WAN3 will bring up different configuration page. Here, we take WAN1 (ADSL/VDSL2) as an example.

On the next page as shown below, please select the appropriate protocol according to the information from your ISP. For example, you should select PPPoE mode if the ISP provides you PPPoE interface. Then click Next for next step.

PPPoE/PPPoA

1. Choose WAN1 as WAN Interface and click the Next button; you will get the following page.
2. After finished the above settings, simply click Next.
3. Please manually enter the Username/Password provided by your ISP. Then click Next for viewing summary of such connection.
4. Click Finish. A page of Quick Start Wizard Setup OK!!! will appear. Then, the system status of this protocol will be shown.
5. Now, you can enjoy surfing on the Internet.

MPoA / Static or Dynamic IP

1. Choose WAN1 as WAN Interface and click the Next button; you will get the following page.
2. Please enter the IP address/mask/gateway information originally provided by your ISP. Then click Next for viewing summary of such connection.
3. Click Finish. A page of Quick Start Wizard Setup OK!!! will appear. Then, the system status of this protocol will be shown.
4. Now, you can enjoy surfing on the Internet.

Customer Service

If the router cannot work correctly after trying many efforts, please contact your dealer/DrayTek for further help right away. For any questions, please feel free to send e-mail to “support@draytek.com”.

Be a Registered Owner
Web registration is preferred. You can register your Vigor router via https://myvigor.draytek.com.

Firmware & Tools Updates
Due to the continuous evolution of DrayTek technology, all routers will be regularly upgraded. Please consult the DrayTek web site for more information on newest firmware, tools and documents. https://www.draytek.com

References

• Home | DrayTek
• MyVigor - DrayTek
• Home | DrayTek

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>