PPE Allison 2000 Series Performance Transmission Cooler Bar and Plate Installation Guide

PPE Allison 2000 Series Performance Transmission Cooler Bar and Plate

Performance Transmission Cooler

Product Information

• Brand : PPEpower.com
• Type : Bar and Plate style Transmission Cooler
• Compatible with : 2017-2020+ GM 6.6L Duramax (L5P) w/ Allison 1000/2000 Series Transmissions
• Model Number : 124065000
• Disclaimer : Performance products can increase horsepower above and beyond factory specifications. Additional horsepower creates more stress on the drive-train components, which could result in drive-train failure.
• Note regarding emissions-related, non-E.O.-legal products: THESE PRODUCTS ARE LEGAL IN CALIFORNIA ONLY FOR RACING VEHICLES THAT MAY NEVER BE USED, OR REGISTERED OR LICENSED FOR HIGHWAY OR OFF-ROAD USE.
• Limitation of Warranty : The Seller gives Limited Warranty as to description, quality, merchantability, and fitness for a particular purpose, productiveness, or any other matter of Seller’s product sold herewith.

Product Usage Instructions

Disassembly:

1. Vehicle off. Engine cool.

2. Remove under hood radiator cover.

3. Disconnect fog lights.

4. Access bumper bolts and remove using a 24 long extension.

5. Remove bumper.

6. Remove clips from left and right trans cooler lines.
   TIP : To minimize spillage, put a towel/rag around the lines.

7. Disconnect factory transmission cooler lines.

8. Remove factory top bracket bolts. Save both factory top bracket bolts for reuse.

9. Remove stock trans cooler and set aside.

Installation

1. Remove PPE fittings. Coat fittings with anti-seize. Install and tighten both to 80 inch lbs.
2. Bolt both lower, rear Transmission Cooler brackets (B) to the vehicle bumper bracket with supplied hardware (C).
3. Align and bolt both driver and passenger side lower Transmission Cooler tabs to lower, rear Transmission Cooler bracket (B) with supplied hardware (D, E). Tighten all hardware.
4. Position PPE Transmission Cooler between bumper brackets and install top, passenger and driver side upper bracket bolts reusing saved factory hardware. Leave loose for now.
5. Attach plastic air deflector to driver and passenger side lower Transmission Cooler mounts with lower Transmission Cooler bolt hardware included (F).
6. Snap-fit transmission cooler fluid lines into the transmission cooler fittings. Check to ensure a tight fit.
7. Slide and snap black plastic retainer clips into position on both fittings.
8. Recheck fittings and tighten all hardware.
9. Start engine. Check fluid level. Fill as needed.
10. Check for leaks.
11. Install bumper, grill and cover.
12. Installation complete.

DISCLAIMER OF LIABILITY

Performance products can increase horsepower above and beyond factory specifications. Additional horsepower creates more stress on the drive-train components, which could result in drive-train failure. Note regarding emissions-related, non-E.O.-legal products: THESE PRODUCTS ARE LEGAL IN CALIFORNIA ONLY FOR RACING VEHICLES THAT MAY NEVER BE USED, OR REGISTERED OR LICENSED FOR HIGHWAY OR OFF-ROAD USE. This agreement sets forth the terms and conditions for the use of PPE products. The installation of this product indicates that the Buyer has read and understands this agreement and accepts the terms and conditions. PPE (Pacific Performance Engineering) Inc., its distributors, employees, and dealers (the “Seller”) shall not be responsible for the product’s proper use and service. The buyer hereby waives all liability claims.

The Buyer hereby acknowledges no reliance on the Seller’s skill or judgment to select or furnish goods suitable for any particular purpose and that there are no liabilities which extend beyond the description on the face hereof, and the Buyer hereby waives all remedies or liabilities expressed or implied, arising by law or otherwise (including without any obligation of the Seller with respect to fitness, merchantability and consequential damages), or whether or not occasioned by the Seller’s negligence. The Seller disclaims any warranty and expressly disclaims any liability for personal injury or damages. The Buyer acknowledges and agrees that the disclaimer of any liability for personal injury is a material term for this agreement and the Buyer agrees to indemnify the Seller and to hold the Seller harmless from any claim related to the item of equipment purchased. Under no circumstances will the Seller be liable for any damages or expenses by reason of use or sale of any such equipment. The Seller assumes no liability regarding the improper installation or misapplication of its products. It is the installer’s responsibility to check for proper installation and if in doubt, contact the manufacturer. The Buyer is solely responsible for all warranty issues from the manufacturer.

LIMITATION OF WARRANTY

The Seller gives Limited Warranty as to description, quality, merchantability, and fitness for a particular purpose, productiveness, or any other matter of Seller’s product sold herewith. The Seller shall not be responsible for the products proper use and service and the Buyer hereby waives all rights other than those expressly written herein. This warranty shall not be extended, altered or varied except by a written instrument signed by Seller and Buyer. Limited lifetime warranty on all PPE cast aluminum products, and PPE Transmission Coolers. Three (3) year limited warranty on PPE Manifolds and Up- Pipes Kits, and OEM-Length Up-Pipes. One (1) year limited warranty on all other PPE products from the date of sale to original buyer and limited solely to the parts contained within the products kit. All products that are in question of Warranty must be returned prepaid to the Seller and must be accompanied by a dated proof of purchase receipt. All Warranty claims are subject to approval by Seller. Under no circumstances will the Seller be liable for any labor charged or travel time incurred in diagnosis for defects, removal, or re-installation – of this product or any other contingent expenses. Under no circumstances will the Seller be liable for any damage or expenses incurred by reason of the use or sale of any such equipment. In the event that the buyer does not agree with this agreement: the buyer may promptly return this product, in a new and unused condition in its original packaging, with a dated proof of purchase to the place of purchase within ten (10) days from date of purchase for a full refund. The installation of this product indicates that the buyer has read and understands this agreement and accepts its terms and conditions.

Performance Transmission Cooler

CONTENTS

• A : Bar and Plate style Transmission Cooler with Fittings (1)
• B : Lower rear mounting brackets (2)
• C : Bracket bolts (2)
• D : Bracket nuts (4)
• E : Cooler to bracket fasteners (4)
• F : Lower transmission cooler bolts (2)

PPEpower.com

References

• Pacific Performance Engineering

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>