Target Blu Eye 2 Vehicle Alert System User Manual

Target Blu Eye 2 Vehicle Alert System

Product Information

TARGET BLU EYE 2 + LASERTRACK

The TARGET BLU EYE 2 + LASERTRACK is a device that warns the driver about approaching emergency services and laser guns. It has an LED display that is installed behind the glass of the rear-view mirror. The display can be operated using buttons 1 and 2 located on the bottom edge of the mirror.

BLU EYE + LASERTRACK; LED Display Functions

• Signal strength meter
• Display number of emergency services/laser measurement in front
• Status LED Laser measurement behind

The left side of the signal strength meter indicates minimum volume (green) and maximum volume (red). There are 5 different levels to choose from. At level 1, the sound is turned off, and LaserTrack notifications are also not displayed audibly now.

Memory Function for Switching On/Off

The settings menu exits automatically after 30 seconds. You can also exit the menu by pressing and holding both buttons simultaneously for 2 seconds. The changed settings are saved.

Volume and Brightness

The volume and brightness levels can be adjusted using buttons 1 and 2 located on the bottom edge of the mirror.

Mute

You can activate MUTE by briefly pressing button 1. After this,the LEDs of the selected CITY MODE level light up constantly, and the system is muted. When a new notification is made, you are automatically alerted again by the acoustic signal. You can deactivate MUTE manually by briefly pressing button 1 again.

City/Highway Mode

You can switch between CITY and HIGHWAY mode by briefly pressing button 2. After 5 seconds, the LEDs of the selected CITY MODE level light up constantly, and the setting is saved.

Visual and Acoustic Alarms for Approaching Emergency Services

If an emergency service approaches you, you will receive notifications in the form of periodic log-on, acoustic alert,communication (speech) and data transfers, and repeating double tone within one second.

Visual and Acoustic Alarm LaserTrack Flare

If laser detection is activated and a laser gun is aimed at your car, you will receive notifications in the form of visual and  acoustic alarms. The same applies when laser protection isactivated and a laser gun is aimed at your car. When laser protection ends, LaserTrack automatically goes into Cooldown. The status LED lights up red and turns on and off smoothly; laser protection is inactive. At the end of Cooldown, a short acoustic signal sounds. The status LED lights up green; laser protection is active again. The laser protection and cooldown times are set by the technician and can be adjusted if necessary.

Product Usage Instructions

1. Install the TARGET BLU EYE 2 + LASERTRACK device behind the glass of the rear-view mirror.
2. Adjust the volume and brightness levels using buttons 1 and 2 located on the bottom edge of the mirror.
3. Switch between CITY and HIGHWAY mode by briefly pressing button 2. After 5 seconds, the LEDs of the selected CITY MODE level light up constantly, and the setting is saved.
4. Activate MUTE by briefly pressing button 1. After this, the system is muted. When a new notification is made, you are automatically alerted again by the acoustic signal. You can deactivate MUTE manually by briefly pressing button 1 again.
5. When an emergency service approaches you, you will receive notifications in the form of periodic log-on, acoustic alert, communication (speech) and data transfers, and repeating double tone within one second.
6. If laser detection is activated and a laser gun is aimed at your car, you will receive notifications in the form of visual and acoustic alarms. The same applies when laser protection is activated and a laser gun is aimed at your car.
7. When laser protection ends, LaserTrack automatically goes into Cooldown. The status LED lights up red and turns on and off smoothly; laser protection is inactive. At the end of Cooldown, a short acoustic signal sounds. The status LED lights up green; laser protection is active again.

INTRODUCTION

Thank you for choosing Target Blu Eye 2. With Target Blu Eye, you will always be alerted in plenty of time for approaching emergency services such as ambulances, fire brigades, police and unmarked surveillance vehicles. Even when they are travelling at high speed and without siren and flashing lights.
The emergency services use what is known as Tetra radio systems. As soon as the radio in an emergency vehicle is switched on, it periodically transmits ultra-short pulses to antenna masts in the network. These pulses are detected by Target Blu Eye and converted into an alert signal.
As a result, Target Blu Eye makes an important contribution to your safety, the safety of the emergency services and the safety of your fellow road users.

BLU EYE STAND + LASERTRACK; LED DISPLAY FUNCTIONS
The LED display is installed by the technician behind the glass of the rear- view mirror. The display can be operated using buttons 1 and 2 located on the bottom edge of the mirror.

PRODUCT MEMORY FUNCTION FOR SWITCHING ON/OFF

Target Blu Eye features an on/off memory function. Don’t want your system to turn on automatically when the ignition is switched on?

• Then, before turning off the car ignition, press button 1 for 2 seconds;a short beep sounds and the status LED goes out.
• The system is now off and remains off even when the ignition is switched on again.
• To switch on the system, press button 1 for 2 seconds; the system boots up and the status LED lights green.

VOLUME AND BRIGHTNESS

Activate the settings menu to adjust the volume of the signal generator and the brightness of the display to your personal requirements.

• Press and hold both buttons simultaneously for at least 2 seconds; a short acoustic signal sounds and the status LED lights up yellow.

• Volume: press button 1 as many times as necessary until the desired volume is reached.
  The left side of the signal strength meter indicates minimum volume (green) and maximum volume (red).
  There are 5 different levels to choose from.
  Caution! At level 1, the sound is turned off. LaserTrack notifications are also not displayed audibly now.

• Brightness: press button 2 as many times until the desired brightness is reached. The right side of the signalstrength meter indicates minimum brightness (green) and maximum brightness (red).
  5 different levels can be selected.

The settings menu exits automatically after 30 seconds. You can also exit the menu by pressing and holding both buttons simultaneously for 2 seconds. The changed settings are saved.

MUTE
Suppresses acoustic alarms temporarily.

• Press button 1 once briefly to activate the MUTE function; a short acoustic signal sounds and the status LED flashes blue.
• The MUTE status remains activated 30 seconds after the last notification. When a new announcement is made, you are automatically alerted again by the acoustic signal. You can deactivate MUTE manually by briefly pressing button 1 again.

CITY / HIGHWAY MODE
In CITY MODE, a threshold value for alarms is set. This setting is recommended within built-up areas when there are many and strong emergency service signals.

In HIGHWAY MODE, there is no threshold for alarms. This setting is recommended on country roads.

CITY MODE has 3 levels:

• Level 1: 1st green LED.
• Level 2: 2nd green LED.
• Level 3: 1st orange LED.

HIGHWAY MODE

• Press button 2 once briefly and press it again each time within 5 seconds until the desired level is selected.
  After 5 seconds, the LEDs of the selected CITY MODE level light up constantly and the setting is saved.

VISUAL AND ACOUSTIC ALARMS FOR APPROACHING EMERGENCY SERVICES

VISUAL AND ACOUSTIC ALARMS FOR APPROACHING EMERGENCY SERVICES
If an emergency service approaches you, you will receive the following notifications:

• The LEDs of the signal strength meter light up from green to red. Green indicates a greater distance to an emergency service. When red, the emergency service is in your immediate vicinity.
• An acoustic warning signal can be heard.

VISUAL AND ACOUSTIC ALARM LASERTRACK FLARE
When approaching memory-programmed automatic gates and/or doors, you will receive the following notifications:

Visual:

• 3 white LEDs (headlights) in the display light up : contact with remote transponder front.
• 3 red LEDs (rear lights) in the display light up : contact with remote transponder rear side.

Acoustic: two short sound signals

If laser detection is activated and a laser gun is aimed at your car, you will receive the following notifications:

Visual:

• 3 white LEDs (headlights) flash in the display : laser measurement at the front.
• 3 red LEDs (rear lights) flash in the display : laser measurement at the rear

Acoustic: alarm tone

If laser protection is activated* and a laser gun is aimed at your car, you will receive the following notifications:

Visual:

• 3 white LEDs (headlights) flash in the display : laser measurement at the front.
• 3 red LEDs (rear lights) flash in the display : laser measurement at the rear.

Acoustic: alarm tone

When laser protection ends, LaserTrack automatically goes into Cooldown. The status LED lights up red and turns on and off smoothly; laser protection is inactive.

At the end of Cooldown, a short acoustic signal sounds. The status LED lights up green; laser protection is active again.

The laser protection and cooldown times are set by the technician and can be adjusted if necessary.

PAUSING LASER PROTECTION / DELETING LASER PROTECTION SOFTWARE (FACTORY RESET)

Pausing laser protection during an alarm:

• Press one of the buttons (short press).
• The status LED will fade red; laser protection is now inactive.

Delete the laser protection software:

• Press and hold button 2 for 3 seconds.
• The status LED will light up blue; laser protection and Laser detection are now deleted
• The remote control function for automatic gates and/or doors remains active.

Delete the laser protection software during an alarm:

• Press and hold button 2 for 3 seconds.
• The status LED will light up blue during 3 seconds and then switch to cooldown mode; laser protection and Laser detection are now deleted.
• The remote control function for automatic gates and/or doors remains active.
  To reset the laser protection function, LaserTrack’s firmware must be reinstalled.
  The remote control and laser detection function of LaserTrack may be used everywhere in Europe.
  However, as laser protection, LaserTrack is not allowed everywhere. Make sure you always act in accordance with local laws.

Zuidergracht 21 | 3763 LS Soest | the Netherlands
info@tracktechnologies.nl | +31 (0)35 760 5760
www.tracktechnologies.nl | www.blu- eye.eu

References

• Home | Target Blu Eye
• Home | Target Blu Eye

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>