Target Atticus Console Table Instruction Manual
- June 3, 2024
- Target
Table of Contents
Target Atticus Console Table
ATTICUS CONSOLE TABLE
INDOOR USE ONLY · SIMPLE ASSEMBLY REQUIRED · MADE IN CHINA H 78 CM x W 100
CM x D 30 CM · LOAD LIMIT: 20 KG PER SHELF
MDF with metal frame.
WARNING:
Do not stand on product. Do not use as a step ladder. Do not use product
unless
CARE INSTRUCTIONS
all bolts, screws and knobs are firmly secured. Only use on even surfaces.
Product should be anchored to wall or other suitable surface to prevent
tipping. Failure to follow these warnings could result in serious injury. Wipe
clean with a soft, damp cloth. Do not use abrasive materials or solvents.
Store in a dry place.
WARNING:
It is STRONGLY RECOMMENDED that you ANCHOR this product.
This product has been fitted with an anchor strap/bracket. To prevent your
furniture from tipping forward it is strongly recommended that you securely
attach this product to a wall or other solid surface, using the anchor
straps provided and appropriate fixings.
IMPORTANT
Regularly check that anchors are securely maintained.
Use safety drawer locks to prevent children climbing.
Stability of tall item may be affected by thick pile carpet or uneven floors.
Do not place unanchored televisions on furniture.
CAUTION:
For your safely when attaching the anchor fixings, please note the following:
- Check for any electrical wires or plumbing inside the wall before drilling any holes (if unsure please seek professional advice from a qualified trades person)
- Walls are constructed from different materials, for example, masonry (solid brick) or plasterboard lined cavity walls (hollow). It is important that you use the appropriate fixings for your wall type.
- – Your local hardware store will have the necessary drills and fixings and can offer advice if needed. If in doubt, engage the services of a qualified trades person to install and anchor the product.
ASSEMBLY INSTRUCTIONS
Please read instructions carefully. Remove all wrapping material, staples and packing straps from the carton. See Parts List and Hardware List for guidance. Be sure you have all parts before you start assembling. Place all wooden furniture parts on a clean and flat soft surface, such as carpet or a rug to prevent from being scratched.
PARTS LIST
- Top Panel : 1PC
- Upper Metal Support Rail : 2PCS
- Metal Side Frame : 2PCS
- Bottom Panel : 1PC
- Bottom Metal Support Rail : 2PCS
- Corner Brace : 4PCS
A.Short Bolt : 24PCS
B.Long Bolt : 20PCS
C.Allen Key : 1PC
D.Screw : 1PC
E.Plastic Anchor : 1 PC
F.Anti Tip Strap : 1 PC
G.Flat Washer : 2PCS
FOR ASSEMBLY
- First, check the content to make sure that nothing is missing.
- Sort out the parts and fittings as shown. Assemble product step by step.
- Do not overtighten screws and fittings.
- Re-tighten all screws and fittings periodically.
WARNING
|
- Never allow children to climb
- Do not stand on product.
- Do not use as a step ladder.
Use of tip-over restraints may only reduce, but not eliminate, the risk of tip-over.
---|---
Serious or fatal crushing injuries can occur from furniture tip-over. To help
prevent tip-over:
- Unless specifically designed
to accommodate, do not set TVs or other heavy object on top of this product.
CAUTION: if using power tool drill be careful not to over tighten
hardware as this may damage parts
NOTE:TOP TUBES HOLES(?) TO
Note: Fully tighten all bolts/screws once fully assembled. Check furniture
regularly to ensure all bolts/screws are secure and tighten any loose
bolts/screws.
Drill a hole in the wall and insert the Plastic Anchor.
Insert screw through Flat Washer and Anti Tip Strap into hole in wall.
Note: this tipping restraint hardware can not be used on brick or wood.
You should seek an appropriate alternative for wall materials other than
plaster