Target Blu Eye 2 Stand Alone Vehicle Alert System User Manual
- June 11, 2024
- Target
Table of Contents
Target Blu Eye 2 Stand Alone Vehicle Alert System
Introduction
The Target Blu Eye 2 Stand-Alone is a device that warns drivers of approaching emergency services vehicles. It has visual and acoustic alarms that alert the driver of emergency services vehicles that are approaching.
BLU EYE Stand-Alone; LED Display Functions
The LED display is installed by the technician behind the glass of the rear- view mirror. The display can be operated using buttons 1 and 2 located on the bottom edge of the mirror.
- Signal strength meter
- Display the number of emergency services/laser measurements in front
- Status LED Laser measurement behind the system boots up and the status LED lights blue.
The settings menu exits automatically after 30 seconds. You can also exit the menu by pressing and holding both buttons simultaneously for 2 seconds. The changed settings are saved.
Memory Function for Switching On/Off
The device has a memory function that saves your last setting for switching on/off. After 5 seconds, the LEDs go out and the setting is saved.
Volume and Brightness
The volume and brightness of the device can be adjusted using buttons 1 and 2 located on the bottom edge of the mirror.
Mute
The mute function can be activated by briefly pressing button 1. When an alert is made, you are automatically alerted again by the acoustic signal. You can deactivate MUTE manually by briefly pressing button 1 again.
City/Highway Mode
The device has two modes: city and highway. The city mode reduces the sensitivity of the device to prevent false alarms in urban areas. The highway mode increases the sensitivity of the device to detect emergency services vehicles at a greater distance.
Visual and Acoustic Alarms for Approaching Emergency Services
If an emergency service approaches you, you will receive the following notifications:
Type of communication | Periodic log-on | Acoustic alert Target Blu Eye |
---|
Emergency services vehicles log on periodically to the nearest
TETRA base station. Even if the TETRA equipment is not used for
communication. Target Blu Eye recognizes such log-on, you will be
warned by a short, repeating beep (mostly 4 seconds).| Short, repeating
signal, mostly 4 seconds interval
If emergency vehicles communicate with each other or with the
emergency room you will be warned by a repeating double tone
within’ one second. You will also be warned in case of data
transfers between emergency vehicles or between an emergency
vehicle and the emergency room.| Repeating double tone within’ one second
Contact Information
- Zuidergracht 21 | 3763 LS Soest | the Netherlands
- Email:info@tracktechnologies.nl
- Phone: +31 (0)35 760 5760
- Websites:www.tracktechnologies.nl
- www.blu-eye.eu
INTRODUCTION
- Thank you for choosing Target Blu Eye 2. With Target Blu Eye, you will always be alerted in plenty of time for approaching emergency services such as ambulances, fire brigades, police and unmarked surveillance vehicles. Even when they are travelling at high speed and without siren and flashing lights.
- The emergency services use what is known as Tetra radio systems. As soon as the radio in an emergency vehicle is switched on, it periodically transmits ultra-short pulses to antenna masts in the network. These pulses are detected by Target Blu Eye and converted into an alert signal.
- As a result, Target Blu Eye makes an important contribution to your safety, the safety of the emergency services and the safety of your fellow road users.
BLU EYE STAND-ALONE; LED DISPLAY FUNCTIONS
- The LED display is installed by the technician behind the glass of the rear-view mirror. The display can be operated using buttons 1 and 2 located on the bottom edge of the mirror.
MEMORY FUNCTION FOR SWITCHING ON/OFF
- Target Blu Eye features an on/off memory function. Don’t want your system to turn on automatically when the ignition is switched on?
- Then, before turning off the car ignition, press button 1 for 2 seconds; a short beep sounds and the status LED goes out.
- The system is now off and remains off even when the ignition is switched on again.
- To switch on the system, press button 1 for 2 seconds; the system boots up and the status LED lights blue.
VOLUME AND BRIGHTNESS
- Activate the settings menu to adjust the volume of the signal generator and the brightness of the display to your personal requirements.
- Press and hold both buttons simultaneously for at least 2 seconds; a short acoustic signal sounds and the status LED lights up yellow.
- Volume: press button 1 as many times as necessary until the desired volume is reached.
- The left side of the signal strength meter indicates minimum volume (green) and maximum volume (red). There are 5 different levels to choose from.
- Caution! Level 1, means that the sound has been powered off.
- Brightness: press button 2 as many times until the desired brightness is reached.
- The right side of the signalstrength meter indicates minimum brightness (green) and maximum brightness (red). 5 different levels can be selected.
- The settings menu exits automatically after 30 seconds. You can also exit the menu by pressing and holding both buttons simultaneously for 2 seconds. The changed settings are saved.
MUTE
Suppresses acoustic alarms temporarily
- Press button 1 once briefly to activate the MUTE function; a short acoustic signal sounds and the status LED flashes blue.
- The MUTE status remains activated 30 seconds after the last notification. When a new announcement is made, you are automatically alerted again by the acoustic signal.
- You can deactivate MUTE manually by briefly pressing button 1 again.
CITY / HIGHWAY MODE
- In CITY MODE, a threshold value for alarms is set. This setting is recommended within built-up areas when there are many and strong emergency service signals.
- In HIGHWAY MODE, there is no threshold for alarms. This setting is recommended on country roads.
CITY MODE has 3 levels:
- Level 1: 1st green LED.
- Level 2: 2nd green LED.
- Level 3: 1st orange LED.
- Press button 2 once briefly and press it again each time within 5 seconds until the desired level is selected. After 5 seconds, the LEDs of the selected CITY MODE level light up constantly and the setting is saved.
HIGHWAY MODE
- Press button 2 once briefly and press it again each time within 5 seconds until both red LEDs light up. After 5 seconds, the LEDs go out and the setting is saved.
VISUAL AND ACOUSTIC ALARMS FOR APPROACHING EMERGENCY SERVICES
- If an emergency service approaches you, you will receive the following notifications:
- The LEDs of the signal strength meter light up from green to red. Green indicates a greater distance to an emergency service. When red, the emergency service is in your immediate vicinity.
- An acoustic warning signal can be heard.
Type of communication | Acoustic alert Target Blu Eye | Explanation |
---|---|---|
Periodic log-on | Short, repeating signal, mostly 4 seconds interval | Emergency |
services vehicles log-on perio- dically to the nearest TETRA base station.
Even if the TETRA equipment is not used for communication. Target Blu Eye
recognizes such log-ons, you will be warned by a short, repeating beep (mostly
4 seconds).
Communication (speech) and data transfers| Repeating double tone within’ one
second| If emergency vehicles communicate with each other or with the
emergency room you will be warned by a repeating double tone within’ one
second. You will also be warned in case of data transfers betweeen emer- gency
vehicles or between an emergency vehicle and the emergency room.
- Zuidergracht 21
- 3763 LS Soest
- the Netherlandsinfo@tracktechnologies.nl
- +31 (0)35 760 5760www.tracktechnologies.nl
- www.blu-eye.eu
Documents / Resources
|
Target Blu Eye 2 Stand Alone Vehicle Alert
System
[pdf] User Manual
Stand-Alone, Blu Eye 2 Stand Alone Vehicle Alert System, Blu Eye 2, Stand
Alone Vehicle Alert System, Vehicle Alert System, Alert System
---|---
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>