HINKLEY 3640 Lighting Harper 3 Light Instruction Manual

: June 3, 2024
: HINKLEY

Table of Contents

HINKLEY 3640 Lighting Harper 3 Light
Mounting Instructions
wiring instructions
Chain Hun g
Grounding instructions
Post-Mount
References
Read User Manual Online (PDF format)
Download This Manual (PDF format)

HINKLEY 3640 Lighting Harper 3 Light

HINKLEY-3640-Lighting-Harper-3-Light-PRODUCT

Mounting Instructions

Find a clear area in which you can work.
Unpack fixture and glass from carton.
Carefully review instructions prior to assembly.

The construction of this fixture will be accomplished by first attaching the mounting strap to the junction box, making all necessary electrical connections, hanging the fixture from the ceiling, and then installing the glass.

Strap Detail

Install screws (A) into mounting plate (B) – see Drawing 1. Be sure the holes into which the screws are threaded match the spacing of the holes (C) in the canopy (D)-see Drawing 1 and 2.
Attach mounting plate (B) to junction box (J), using screws (G) not provided and then slip supply wires through large center hole.

SAFETY WARNING: READ WIRING AND GROUNDING INSTRUCTIONS (I.S. 18) AND ANY ADDITIONAL DIRECTIONS. TURN POWER SUPPLY OFF DURING INSTALLATION. IF NEW WIRING IS REQUIRED, CONSULT A QUALIFIED ELECTRICIAN OR LOCAL AUTHORITIES FOR CODE REQUIREMENTS.

Fixture Mounting

HINKLEY-3640-Lighting-Harper-3-Light-FIG-2

Hang the fixture by slipping screws (A) through holes (C) of canopy (D) -see drawing 2
Thread on barrel knobs (E) onto end of screws (A) and tighten to secure fixture to ceiling

Glass install

HINKLEY-3640-Lighting-Harper-3-Light-FIG-3

Lamp fixture before installing glass
To assemble glass use hex nuts (H) to secure glass arms (Z) to canopy
Lift glass towards canopy (D)
Next slide center ring (R) over glass
Use the three knobs (K) to secure glass (G) and ring (R) to canopy (D)
Fixture can now be powered on

I.S. 18 wiring grounding instructions

SAFE TY WARNI NG: READ WIRIN G AND GROUNDING INSTRUCTIO NS (IS 18) AND ANY ADDITIONAL DIRECTIONS. TURN POWER SUPPLY OFF DURING INSTALLATION. IF NEW WIRING IS REQUIRED, CONSULT A QUALIFIED ELECTRICIAN OR LOCAL AUTHORITIES FOR CODE REQUIREMENTS

wiring instructions

Indoor Fixtures

Connec t positive supply wire (A ) (typically black or the smooth, unmarked side of the two-conduc tor cord) to positive ﬁxture lead (B) with appropriately sized twist on connector – see Dra w ings 1 or 2.
Connec t negative supply wire (C) (typically white or the ribbed, marked side of the two-conductor cord) to negative ﬁxture lead (D).
Please refer to the grounding instructions below to complete all electrical connections

Flus h Mount

Outdoor Fixtures

Connec t positive supply wire (A) (typically black or the smooth unmarked side of the two-conduc tor cord) to positive ﬁxture lead (B) with appropriately sized twist on connector — see Drawings 2 or 3.
Connec t negative supply wire (C) (typically white or the ribbed, marked side of the two-conductor cord) to negative ﬁxture lead (D).
Cover open end of connectors with silicone sealant to form a watertight seal.
If installing a wall mount ﬁxture, use caulk to seal gaps between the ﬁxture mounting plate (backpla te) and the wall. This will help prevent water from entering the outlet box. If the wall surface is lap siding, use caulk and a ﬁxture mounting platform specially.
Please refer to the grounding instructions below to complete all electrical connections.

Chain Hun g

Grounding instructions

Flush Mount Fixtures
For positive grounding in a 3-wire electrical system, fasten the ﬁxture ground wire (E) (typically copper or green plastic coated) to the ﬁxture mounting strap (M ) with the ground screw (S) – see Draw in g 1.

Note: On straps for screw supported ﬁxtures, ﬁrst install the two mounting screws in strap. Any remaining tapped hole may be used for the ground screw.

Chain Hung Fixtures
Loop ﬁxture ground wire (E) (typically coppe r or green plastic coated) under the head of the ground screw (S) on ﬁxture mounting strap (M) and connect to the loose end of the ﬁxture ground wire directly to the ground wire of the building system with appropriately sized twist-on connectors – see Draw in g 2.

Post-Mou nt Fixtur es
Connec t ﬁxture ground wire (E) (typically copper or green plastic coated) to power supply ground with appropriately sized twist-on connector inside post. Cover open end of connector with silicone sealant to form a watertight seal – see Drawing 3.