CENTEK CT-1841 Range Hood Instruction Manual

CT-1841 Range Hood
Instruction Manual

CT-1841 Range Hood

Dear Customer,
Thank You for purchasing a CENTEK brand product. We guarantee flawless function of this item, provided the guidelines of its operation are observed.
Prior to operating the appliance, please carefully read the present manual which contains important information regarding its proper and safe operation. Take care not to lose the present manual. The manufacturer will not be responsible for any damage resulting from improper use of the appliance or from non-observance of the instructions and provisions of the present manual, as well as from attempts by unskilled persons at repairing the appliance. Should You decide to transfer the appliance to another person, please pass the present manual over along with it.
The hood is a household appliance and is not intended for industrial use!

SECURITY MEASURES

The device you purchased complies with all official safety standards applicable to electrical appliances in the Russian Federation. In order to avoid situations that are dangerous to life and health, as well as premature failure of the device, it is necessary to strictly observe the following conditions:

• Read this manual carefully before putting the device into operation.
• Keep this manual.
• Make sure that the voltage indicated on the device corresponds to the voltage in the power supply network. Do not use adapters to avoid fire.
• It is forbidden to use accessories and spare parts from other manufacturers. If such parts are used, the manufacturer’s warranty is void. Replacement of lamps with lamps of other manufacturers is allowed, provided that the installed lamps will not differ in type, form factor, dimensions and will not exceed the power of the original lamps installed by the manufacturer.
• Do not use the appliance if the power cord, plug and other parts of the appliance are damaged.
• If the power cord is damaged, its replacement, in order to avoid danger, must be carried out by the manufacturer, the service department or similar qualified personnel.
• During the first use, a slight unpleasant odor may appear (which will disappear after several uses), which is explained by the possible presence of residues of oils and other substances on the internal surfaces.
• The device must be installed so that its lower surface is at least 65 cm from the heating plane of the electric furnace or 75 cm from the heating plane of the gas furnace.
• Be careful when working simultaneously with the hood and burner (hearth). The hood sucks in air along with oxygen, which is needed for the gorenje process.
• The negative pressure in the room should not exceed 4Pa (4×10-5 bar). For reliable and safe operation, ventilation of the room should be provided.
• Do not check the condition of the filters while the device is running.
• Do not touch the lamp or adjacent areas during operation of the lighting system or immediately after it is turned off.
• To avoid overloading the power supply, do not use this device at the same time with energy-intensive devices.
• The device is not intended for use by persons (including children) with reduced physical, sensory or mental abilities or lack of life experience or knowledge, unless they are supervised or instructed to use the device by a person responsible for their safety. Children should be supervised to prevent playing with the device.
• If smoke appears, turn off the appliance immediately and disconnect it from the mains.
• It is forbidden to cook dishes on an open flame under the appliance. Avoid an open flame, as it damages the filters and can lead to a fire. Do not allow a flare flame to appear under the appliance. The flame of the burners should always be covered with dishes.
• Do not use the appliance outdoors.
• Be careful! The surface of the device may heat up during its operation.
• If the connecting pipe consists of two or more parts, then the upper part should be located on top of the lower part. Do not connect the discharge from the appliance to the hot air circulation channel or to the channel used to remove smoke from devices powered by energy other than electrical.
• Before starting to assemble the device, disconnect the grease filter to facilitate its installation.
• If there is no plug on the cable, install a plug designed to work with the load indicated on the characteristics table. If the device is equipped with a plug, then install the device in such a way that the plug is accessible.
• In the case of direct connection to the power grid, a multi-pole switch with a contact gap of at least 3 mm, designed for the desired load and meeting current standards, must be placed between the device and the network.

TECHNICAL SPECIFICATION

2 speed – 52 dB

COMPLETENESS AND DESCRIPTION OF THE DEVICE

• Hood – 1 pc.
• Anti-fat aluminum filter – 2 pcs.
• Lamp – 1 pc.
• Plastic anchor – 6 pcs.
• Self-tapping screw for wall mounting – 6 pcs.
• Check valve lobe – 2 pcs.
• User Manual – 1 pc.

1. Operation speed switch
2. Anti-fat aluminum filters
3. Turning on the backlight
4. Sliding panel
5. Backlight window

The device is supplied with plastic petals of the air duct valve. They are installed in the grooves of the air duct on the product at the last moment upon completion of installation.

WORKING PROCEDURE

Before installing the hood, make sure that:

• the distance from the bottom surface of the hood is at least 65 cm from the heating plane of the electric furnace or 75 cm from the heating plane of the gas furnace;
• the length of the electric cord is sufficient to connect the hood to the mains;
• nothing will damage the electric cord during further operation;
• there is a possibility of duct equipment.

Before starting to assemble the device, disconnect the grease filter to facilitate its installation.
The hood removes smoke into the atmosphere through the outer wall of the building or through an existing ventilation shaft. For this purpose, it is necessary to purchase a sliding non-flammable chimney that complies with current regulations and connect it to the flange. The hood can be mounted in several ways.
WALL MOUNTING
Measure the distance on the wall for mounting the hood. Drill two holes with a diameter of 8 mm, as shown in Figure

1. Make sure that the anchors and screws included in the package are suitable for the type of wall on which the hood will be mounted. Install the anchors, tighten the screws. Remove the protective film from the hood, then install the hood on the screws.
   There are 2 holes with a diameter of 6 mm on the back panel of the hood. Fix the hood to the wall with protective screws using these holes. Install a flange on top of the hood.

MOUNTING UNDER A HINGED CABINET
ATTENTION! The air inlet must be drilled at the bottom of the cabinet. The second hole can be either in the upper part of the cabinet or in its back wall, depending on how you have planned the ventilation. You can also use any available types of pipe, both rigid and soft, to divert air. Measure the distance at the bottom of the hood mounting cabinet. Drill four holes with a diameter of 6 mm, as shown in Figure 2. Install the duct valve petals on top of the hood. Remove the protective film from the hood, then screw the hood to the cabinet.

INSTALLATION INSIDE THE HINGED CABINET
ATTENTION! The air duct hole must be drilled in the cabinet shelf. The second hole can be either in the upper part of the cabinet or in its back wall, depending on how you have planned the ventilation. You can also use any available types of pipe, both rigid and soft, to divert air. Use the mounting template to precisely cut holes in the shelf for the hood itself, the duct, the power cord. With this type of installation, the hood is screwed in exactly the same way as when mounting under the cabinet, with the difference that the screws are screwed not to the bottom of the cabinet, but to the inner shelf. Measure the distance in the shelf of the hood mounting cabinet. Please note that the back wall of the hood should never touch the inner wall of the cabinet. The distance from the back wall of the hood to the wall of the cabinet should be at least 10 cm.
Drill four holes with a diameter of 6 mm in the cabinet shelf. Install the duct valve petals on top of the hood. Remove the protective film from the hood, then screw the hood to the cabinet. It is also allowed to install the hood on the side runners, but this type of installation will require the intervention of specialists in the collection of furniture and the purchase of mounting materials.

CARE OF THE DEVICE

Disconnect the power cord from the mains and allow the engine to cool down. Remove the anti-fat aluminum filters. Rinse them in warm soapy water, then dry them and put them in the hood. This procedure should be performed at least once a month. A filter contaminated with grease is:

• Risk of fire. Oil stuck on the filter is flammable and can cause a fire.
• Decrease in the efficiency of air drainage.
• Risk of failure of the device. Contaminated filters do not provide sufficient air conductivity, which can cause engine overload.

Wash the hood regularly, removing all food residues, fat and other contaminants. Wipe the outer surface only with a damp soft cloth with the addition of detergent.
Storage and operation of the hood should be carried out in dry heated rooms at a temperature not lower than + 5 °C and a relative humidity of not more than 80%.
Transportation of the product should be carried out in accordance with the marking indicated on the package. After transporting the hood in conditions of low temperature, it is allowed to use the device only after two hours of its stay in a warm room.
We apologize if the scope of delivery, dimensions, description, technical characteristics, appearance or color of the product turned out to be inaccurate. The manufacturer reserves the right to change these parameters without prior notice, as a result of which, at the time of purchase of a particular product, they may differ from those indicated earlier.

POSSIBLE PROBLEMS AND WAYS TO FIX THEM

• Before contacting the service center, check the following: Make sure that the hood is connected to the mains. Check the mains voltage.
• By external inspection, check the integrity of the elements of the electrical circuit, in case of malfunction of any element, contact customer service.

Repairs should only be carried out by qualified service center personnel! If your lamp has burned out, you can replace it yourself. To do this, follow these steps:

1. Turn off the appliance and disconnect it from the mains.
2. Remove the lamp cover by unscrewing the 2 screws.
3. Remove the lamp.
4. Replace the lamp with a new one with a base of the same standard.
5. Assemble everything in reverse order.

ENVIRONMENTAL PROTECTION, DISPOSAL OF THE DEVICE

ENVIRONMENTAL PROTECTION
The packaging and the device itself are made of materials that can be reused. If possible, when disposing of them, dispose of them in a container intended for reusable materials.
DISPOSAL OF THE DEVICE
The device can be disposed of separately from ordinary household garbage at the end of its service life. It can be handed over to a special reception point for electronic devices and electrical appliances for recycling. Materials are processed in accordance with their classification. By handing over this device at the end of its service life for recycling, you will make a great contribution to environmental protection. You can get a list of points of reception of electronic devices and electrical appliances for recycling from municipal public authorities.

CERTIFICATION DATA, GUARANTEE

The service life of this item is 8 years since the date of sale to the end user, provided the item will be used in strict accordance with the present manual and the applicable technical standards. Upon expiry of the service life please contact the nearest authorized service centre for suggestions as to further operation of the appliance. The manufacturing date of the appliance is integrated into the serial number (digits 2 and 3 – year, digits 4 and 5 – month of manufacture). Guarantee and post-guarantee maintenance is provided by the General Service Center OOO «Larina-Servis» (Russia, Krasnodar), phone: +7 (861) 991-05-42. The address of the facility authorized with receiving buyer claims, maintenance and repairs is shown on the website https://centek.ru/servis, otherwise refer to the store or other legal entity, where you have purchased this appliances.
The product has the Certificate of Conformity No.: № ЕАЭС RU C-CN.ВЕ02.В.03401/21 from 26.01.2021 y.

INFORMATION ABOUT THE MANUFACTURER, IMPORTER

Imported to EAEU by: Individualniy Predprinimatel Asrumyan Karo Shurikovich.
Address: Russia, 350912 Krasnodar, ul. Atamana Lysenko, 23, pgt. Pashkovskiy, phone: +7 (861) 2-600-900.
DEAR CONSUMER!
The guarantee period for all appliances amounts to 36 months from the date of sale to the end consumer. With this Warranty Card the Manufacturer confirms the proper condition of the appliance and undertakes to repair, free of charge, all defects caused by the Manufacturer’s default.

GUARANTEE MAINTENANCE TERMS

1. The guarantee shall be valid if the following documentation conditions are observed:
   • The original Warranty Card shall be filled out correctly and clearly, indicating the of appliance model, serial number and sale date, the stamp of the seller company and signature of its representative shall be available, as well as the stamps on each coupon and the buyer’s signature in the Warranty Card. The Manufacturer reserves the right to reject guarantee maintenance if the buyer fails to provide the above mentioned documents or if the information contained therein is incomplete, illegible or ambiguous.

2. The guarantee shall be valid if the following operation conditions are observed:
   • the appliance is used in strict accordance with the present manual;
   • the safety rules and requirements are observed.

3. The guarantee does not apply to regular maintenance, cleaning, installation and setup of the appliance at the owner’s location.

4. The guarantee does not apply in the following cases:
   • mechanical damage;
   • normal wear of the appliance;
   • non-observance of operation requirements or erroneous actions on the part of the user;
   • improper installation or transportation;
   • natural disasters (lightning, fire, flood, etc.), as well as any other causes beyond the Manufacturer’s or Seller’s control;
   • ingress of foreign objects, liquids or insects into the inside of the appliance;
   • repairs or modifications to the appliance by unauthorized persons;
   • use of the appliance for commercial purposes (loads exceeding normal domestic application), connection of the appliance to utility and telecommunication networks in compliant with national technical standards;
   • failure of the following accessories, if replacement of these is allowed by design and does not involve disassembly of the appliance:
   a) remote control units, rechargeable batteries, replaceable batteries (power cells), external power supply units and chargers;
   b) consumables and accessories (packaging, covers, slings, carry bags, mesh screens, blades, flasks, plates, supports, grilles, spits, hoses, tubes, brushes, nozzles, dust collectors, filters, smell absorbers);
   • for battery-powered appliances – operation with inappropriate or depleted batteries;
   • for rechargeable battery-powered appliances – any damage caused by improper battery charging and recharging.

5. The present guarantee is provided by the Manufacturer in addition to the consumer rights determined by the applicable legislation and does not limit these rights in any way.

6. The Manufacturer shall not be made liable for possible damage, directly or indirectly inflicted by CENTEK brand products on people, domestic animals, the consumer’s or third persons’ property if such damage is inflicted as the result of non-observance of appliance installation and operation requirements, deliberate or negligent actions (omission) by the consumer or third persons, as well as of force majeure circumstances.

7. Service centers will only accept appliances in a clean state (there should be no food residues, dust and other contamination on the appliance).

The Manufacturer reserves the right to change the design and specifications of the appliance without prior notice.

Warranty certificate
Attention! Please ask the seller to fill out the warranty card and tear-off coupons in full. The ticket is valid in the presence of all stamps and marks.
Product: ———————————-
Model: ———————————–
Serial number: ————————–
Date of sale: —————————–
These tear-off coupons are filled in by a representative of the seller

PRODUCT : ———————————-
MODEL: ————————————-
SERIAL NUMBER: ———————-
DATE OF SALE: ————————–
VENDOR: ————————————
SELLER’S ADDRESS: ———————-
FULL NAME AND PHONE NUMBER OF THE BUYER: ————–
These tear-off coupons are filled in by a representative: —————————-
TYPE OF REPAIR: ———————————————————————
DATE OF RECEIPT: ——————————————————————
RELEASE DATE: ———————————————————————–

References

• Сервис - Официальный сайт Centek
• Сервис - Официальный сайт Centek

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>