os kari Bora 4b Shoe Boots and Gloves Dryer Instruction Manual

June 4, 2024
os kari

os kari Bora 4b Shoe Boots and Gloves Dryer

os-kari-Bora-4b-Shoe-Boots-and-Gloves-Dryer-product

General

We are pleased that you have chosen an OSKARI® product.

  • These operating instructions apply for an English-speaking country of destination and an English-speaking person as a user.
  • The Declaration of Conformity / Declaration by the manufacturer for the machine is included in the appendix.
  • Extreme heat, places where sparks occur or even open flames are near, should be avoided, otherwise the risk of fire with the development of noxious gases or damage to insulation, cables, etc.
  • contacts with concentrated acids or alkalis can cause the decomposition of plastics in or on the unit or dangerous corrosion of metal parts. Optionally impugned parts must be replaced in time.
  • It is important to ensure that air sampling openings are not covered.

Intended use
The Bora ® – footwear, boot, and glove dryer is used exclusively for drying of shoes, boots, and gloves. With proven improper use of any claim expires.

In freestanding use (with feet) shall be provided to prevent slipping

Warranty information

In case of appropriate use, OSKARI® grants a 5-year warranty on the heating elements and functionality.

Excluded from the guarantee are vandalism and age-related wear and tear on the device. OSKARI® takes no liability for damage to the delivered system that are not on improper use, proper work is based, and to third parties. Changes to components are in their own responsibility. Mounting lead in deviating from the manual form leads to the loss of warranty claims for the machine.

Regulations

The OSKARI® shoes, boots, and glove dryer is built according to European and German standards, rules and regulations, tested and operated. For installations, however, country-specific, electrical regulations must be observed.

Device master sheet

  • Type: OSKARI® model BORA® a dryer for shoes, boots, gloves, and sports clothes.

  • OSKARI®
    See Device label: serial number / Year.

  • Dimensions: W / H / D in mm

    • Bora 2 = 250/700/330
    • Bora 4b = 650/700/330
    • Bora 4h = 250/1500/330 os-kari-Bora-4b-Shoe-Boots-and-Gloves-Dryer-fig-3
  • Voltage/frequency: 230 V / 50 Hz ~

  • Protection class: IP 55

  • Execution:
    The stainless-steel panels differ visually in principle only in their dimensions and in their different number of recordings of shoes. os-kari-
Bora-4b-Shoe-Boots-and-Gloves-Dryer-fig-5

Installation

  • Installation instructions: see a mounting set
  • Use only the supplied mounting hardware for assembly.
  • If ordered detached, so the feet are supplied laterally to attach to the Bora®
  • The Oskari – drying systems are supplied plug-in ready 50 Hz for 230V/~

Installation instructions in drying rooms

  1. OSKARI® stainless steel panels for wall mounting at least 15 cm away bottom mount on flat surfaces from the floor.
  2. Only the original supplied mounting kit (screws, plugs, etc.) use.
  3. Start the test run after installation of all mounting screws.
  4. After installing the appliance,
  5. The plug must be accessible.
  6. In the supplied adjustable feet of Oskari – Bora can be taken on horizontal surfaces without further assembly into operation.

ATTENTION!
Improper handling of the device may cause damage to furniture, flooring, and similar things.

INSTALLATION INSTRUCTIONS

in wet rooms:
Make installation as points 1-3 in drying rooms. Plugging in only intended for this purpose Wet room installation (outlet)

Operation

Drying rooms:
Oskari stainless steel panels with a hot-air blower for drying rooms can directly with the timer be put into operation. The built-in stainless steel panel warm air blower is maintenance-free. For drying of shoes, boots and gloves select the appropriate switch. The built-in timer allows individual operating times.

Wet rooms
Oskari stainless steel panels are also suitable for damp locations. They are to be put in a designated damp-proof socket.

Transport and Storage

The unit must be secured during transport to prevent slipping or protection from the weather. If the dryer cannot be immediately after delivery, it must be stored on a dry and clean place. It’s needed to protect the dryer from damage, dirt, and moisture.

Maintenance Manual and Troubleshooting

Should you have any problems with the product or should problems occur, please contact your reseller or your local supplier or directly at info@oskari.at? For more information visit www.oskari.at.

WARNING:
The unit is closed by blind rivets and is never allowed to be opened! Repairs are only allowed by a trained specialist!

Operation of the time

A multifunction timer is installed on the side of the OSKARI®-BORA®.

Operating mode 1:
if you turn the switch to the right, you can set the timer variably from a minimum of 1 minute to a maximum of 4 hours. This is perfect when you come home from exercising and want to dry your shoes and clothes the right way. The time is mechanical and runs automatically without electricity. Switching is therefore not necessary.

Operating mode 2:
If you turn the switch to the left, you switch the dryer to “D” for continuous operation mode. You can choose the duration and start time yourself by inserting a 24-hour timer or a smart plug, etc. You can continue this process as often as you want. Programming can also be carried out under voltage. Mechanical switch-off is therefore no longer necessary.

Disponsal, decommissioning

The panels may be for reuse by specialist disposal (see summary table) and are therefore environmentally friendly.

Detail of the disposal and recycling of components are shown in the following overview:

Produkt Materialien Entsorgung

steel structures transmission Engine parts screws

etc.

|

metals

| Separation of materials

Feed for recycling through melting down

More protective covers housing covers etc.|

plastic wood

| Feed for recycling, incineration or on special landfills
cable housing plug etc.| Rubber, PVC,

silicone, Polychlori nated ears

| separation of materials AdZZditions to recycling
Electronics- assemblies| Plastic metals electrolyte s| On special landfills

in accordance with local, official regulations

Products and parts to devices with paintings must be supplied for recycling or disposed of in accordance with local and federal regulations for special disposal sites.

References

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals