SUNSKY NC1581W WiFi Intelligent Solar Alert PTZ Camera User Manual
- June 6, 2024
- sunsky
Table of Contents
Wifi
Intelligent Solar Energy
Alert PTZ Camera
User Manual
PRODUCTS & PACKING LIST
Product Diagram
Process
- Solar panel: connect the panel to the camera, fix a suitable angle with screws
- Sim and TF card: loosening the cap in the above remark
- insert SIM card and TF card, then tighten the screws.. Power cable: connect the cables between the panel and camera, then tighten the waterproof cap.
- Panel power-on: Remove the rubber of the panel, make sure it is power on. Then put the rubber back to the panel.
INSTALLATION
APP INSTALLATION
Scan the following QR codes or search for °UBox” from the App Store(for as devices) or Google Play Store (for Android smartphones) to download and install the app.
https://apps.apple.com/cn/app/ubox/id1436112326
https://play.google.com/store/apps/details?id=cn.ubia.ubox
APP REGISTRATION
- 0pen the app then input your E-mail address then press ‘Register. Check and select to agree on the agreement then your E-mail box will get a verification code.( For better user experience, please allow to open all permissions to avoid missing any notifications from the app.)
- Input the “Verification code and press ‘Next’. (if you did not find the mail you might find the code in your email spam box. )
- Set the login password and confirm the login password. Then press ‘Register’ to next step.(For your password safety, the password requires more than 8 characters plus a combination of letters)
- Enter your E-mail address, and input your login password. Then press ‘Login’.
WI-FI CONNECTION
- Press ‘Add Family’ then set the room or position as per reminders.
- Enter your family name and then press ‘Next’.
- Input the necessary information just like Country, Province, then press Done’. 4.4. Press ‘Add a device’ to add a smart device
- Conned the device with a power supply, and make sure your mobile phone is connected to an available Wi-Fi. Then press Setup device’
- After the power on the device. wait for the blue LED and voice prompt The device is waiting for pairing. This means your device is in pairing mode.
- you did not hear the voice prompt, please press the RESET button until the blue indicator to light up and then release. The device will reboot and enter the pairing state.
- The app will input the Wi-Fi name automatically, please input the coned Wi-Fi Password. Then you can choose the ‘DR code configuration’ or ‘Sound wave configuration’ .
- Sound wave configuration: Make sure the camera and mobile phone within 1M distance,you will hear the wave sound DI Dl,follow the tips shown in the mobile to finish the configuration.
- OR code configuration: Select the OR code configuration then the mobile phone display a QR code. Use the device to scan to the QR code 10cm away from the mobile phone.
- Select the family name or device location then press ‘Done.’
- The device will enter to the device list automatically. Setup success! The device is ready to use.
4UBIA8ubia180182c6aa01a8c082c6aa01a8c0
DIVICE SETTING
SPECIAL NOTES!
- The device is equipped with a rechargeable lithium battery. The battery life will be affected by the device’s wake-up time and the number of wake-ups. Therefore, the PIR sensor alarm detection function is used in an environment with a lot of people. It is recommended to turn off or set the device to low sensitivity to reduce device wake-up and call times extend battery life. When the battery is low, please charge the battery immediately.
- Keep the device in range of your router. Make sure the device is placed close to the Wi-Fi router. If there has to be thick or insulated objects between the device and the VVi-A router, which may lead to a weak Wi-Fi signal, please make sure the Wi-Fi signal is in a good level before you start using the device.
- It is a delicate device with low power consumption design. Every time the device is awakened and will work for few seconds. After that, the device will enter standby mode to save power. You can set the work time in the app settings.
- Because mainland China does not receive Google’s system push messages, you need to open the app’s self-starting function in your phone to receive push messages.
- This device provides one month of free cloud storage services. If you need to continue using value-added services after the trial period expires, you need to purchase them in the app.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>