RoHS V1-F Fade-In Fade-Out PushplusRF LED Dimmer Owner’s Manual
- June 9, 2024
- RoHS
Table of Contents
RoHS V1-F Fade-In Fade-Out PushplusRF LED Dimmer
5 fading speed/Step-less dimming/Push Dim/Wireless remote control/Multiple protection
Features
- Fade-in Fade-out LED dimmer with smooth fading effect for soft start and stop.
- The fading speed can be set via knob potentiometer, 1S, 3S, 5S, 10S, 20S selectable.
- Connect with self-resetting metal button or push switch to achieve on/off and 0-100%dimming function.
- Push input can accept either positive or negative trigger.
- Match with RF 2.4G single zone or multiple zone dimming remote control optional.
- Over-heat / Over-load / Short circuit protection, recover automatically.
Technical Parameters
Input and Output
Input voltage| 12-48VDC
Input current| 8A
Output voltage| 12-48VDC
Output current| 1CH,8A
Output power| 96-384W
Output type| Constant voltage
Environment
Operation temperature| Ta: -20 OC ~ +55 OC
Case temperature (Max.)| Ta: +85 OC
Dimming data
| Input signal | Push Dim + RF 2.4GHz |
|---|---|
| Control distance | 30m(Barrier-free space) |
| Dimming gray scale | 4096 (2^12) levels |
| Dimming range | 0 -100% |
| Dimming curve | Logarithmic |
| PWM Frequency | 2000Hz (default) |
Warranty
Warranty| 5 years
|
Safety and EMC
EMC standard (EMC)
| ETSI EN 301 489-1 V2.2.3
ETSI EN 301 489-17 V3.2.4
Safety standard(LVD)| EN 62368-1:2020+A11:2020
Radio Equipment(RED)| ETSI EN 300 328 V2.2.2
Certi cation| CE,EMC,LVD,RED
Package
Size| L120 x W43 x H27mm
Gross weight| 0.053kg
|
Mechanical Structures and Installations
Light on/off fading speed
Rotate knob to switch fading speed,
When the fading speed set to 1/3/5/10/20s, the RUN LED indicator will flash 1/2/3/4/5 times.
Wiring Diagram
- Connect with self-resetting metal button, positive trigger input.
Press the button to switch or adjust brightness, the button indicator always lights up.
- Connect with self-resetting metal button, positive trigger input.
Press the button to switch or adjust brightness, the button indicator lights up when pressed.
- Connect with self-latching metal button.
Press the button to power on or off the controller, the button indicator lights up when pressed. Use RF remote to adjust brightness optional.
- Connect with push switch panel, negative trigger input. Press the panel to switch or adjust brightness.
Match Remote Control
Match:
Switch off the power, then switch on power.
Immediately short press on/off key (single zone remote)or zone key (multiple
zone remote) 3 times on the remote.
The light blinks 3 times means match is successful.
Delete:
Switch off the power, then switch on power.
Immediately short press on/off key (single zone remote) or zone key (multiple
zone remote) 5 times on the remote.
The light blinks 5 times means all matched remotes were deleted.
Push Dim Function
The provided Push-Dim interface allows for a simple dimming method using commercially available non-latching (momentary) wall switch or metal button.
-
Short press:
Turn on or off light. -
Long press (1-6s):
Press and hold to step-less dimming,
With every other long press, the light level goes to the opposite direction. -
Dimming memory:
Light returns to the previous dimming level when switched off and on again, even at power failure. -
Synchronization:
If more than one controller are connected to the same push switch, do a long press for more than 10s, then the system is synchronized and all lights in the group dim up to 100%.
This means there is no need for any additional synchrony wire in larger installations.
We recommend the number of controllers connected to a push switch does not exceed 25 pieces, The maximum length of the wires from push to controller should be no more than 20 meters.
Dimming Curve
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>