TELTONIKA FMC003 GPS Tracker Plug and Play User Guide

: June 9, 2024
: teltonika

Table of Contents

KNOW YOUR DEVICE
PINOUT
SET UP YOUR DEVICE
PC CONNECTION (WINDOWS)
HOW TO INSTALL USB DRIVERS (WINDOWS)
CONFIGURATION
QUICK SMS CONFIGURATION
MOUNTING RECOMMENDATIONS
LED INDICATIONS
BASIC CHARACTERISTICS
SAFETY INFORMATION
CERTIFICATION AND APPROVALS
WARRANTY
WARRANTY DISCLAIMER
References
Read User Manual Online (PDF format)
Download This Manual (PDF format)

Telematics
FMC003
Advanced OBDII tracker
Quick Manual v1.1

KNOW YOUR DEVICE

PINOUT

FMC003 OBDII socket pinout

Pin number	Pin name	Description
2	PWM_BUS+/VPW
4	GND (-)	Ground
5	GND (-)	Ground
6	CAN_H	CAN high
7	K-Line
10	PWM_BUS-
14	CAN_L	CAN low
15	L-Line
16	VCC (10 – 30)V DC(+)	Power supply (+10-30 V DC)

FMC003 OBDII socket pinout

SET UP YOUR DEVICE

HOW TO INSERT MICRO-SIM CARD AND CONNECT THE BATTERY

| | |
---|---|---|---
1 COVER REMOVAL
Gently remove FMC003
cover using plastic pry tool
from both sides.| 2 MICRO-SIM CARD INSERT
Insert Micro-SIM card as
shown with PIN request
disabled or read our Wiki
1 how to enter it later in
Teltonika Configurator
2 . Make sure that MicroSIM
card cut-off corner is pointing forward to slot.| 3 BATTERY CONNECTION
Connect battery as shown to
device. Position the battery
in place where it does not
obstruct other components.| 4 ATTACHING COVER BACK
Device is ready to be connected.
Attach device cover back.

1 wiki.teltonika-gps.com/view/FMC003_Security_info
2 wiki.teltonika.lt/view/Teltonika_Configurator

PC CONNECTION (WINDOWS)

Power-up FMC003 with DC voltage (10 – 30 V) power supply using supplied power cable. LED’s should start blinking, see “LED indications1
”.
Connect device to computer using Micro-USB cable or Bluetooth connection:
• Using Micro-USB cable
• You will need to install USB drivers, see “How to install USB drivers (Windows)2”
• Using Bluetooth
• FMC003 Bluetooth is enabled by default. Turn on Bluetooth on your PC, then select Add Bluetooth or other device > Bluetooth. Choose your device named – “FMC003_last_7_imei_digits”, without LE in the end. Enter default password 5555, press Connect and then select Done.
You are now ready to use the device on your computer.

1 wiki.teltonika-gps.com/view/FMC003_LED_status
2 Page 6, “How to install USB drivers”

HOW TO INSTALL USB DRIVERS (WINDOWS)

Please download COM port drivers from here1 .
Extract and run TeltonikaCOMDriver.exe.
Click Next in driver installation window.
In the following window click Install button.
Setup will continue installing the driver and eventually the confirmation window will appear. Click Finish to complete the setup.

1 teltonika-gps.com/downloads/en/fmb120/TeltonikaCOMDriver.zip

CONFIGURATION

At first FMC003 device will have default factory settings set. These settings should be changed according to the users needs. Main configuration can be performed via Teltonika Configurator 1 software. Get the latest Configurator version from here 2 . Configurator operates on Microsoft Windows OS and uses prerequisite MS .NET Framework. Make sure you have the correct version installed.

1 wiki.teltonika-gps.com/view/Teltonika_Configurator
2 wiki.teltonika-gps.com/view/Teltonika_Configurator_versions

MS .Net requirements

Operating system	MS .NET Framework version	Version	Links

Windows Vista
Windows 7
Windows 8.1
Windows 10| MS .NET Framework 4.6.2| 32 and 64 bit| www.microsoft.com1

1 dotnet.microsoft.com/en-us/download/dotnet- framework/net462

Downloaded Configurator will be in compressed archive.
Extract it and launch Configurator.exe. After launch software language can be changed by clicking in the right bottom corner.

Configuration process begins by pressing on connected device.

After connection to Configurator Status window will be displayed.

Various Status window 1 tabs display information about GNSS 2 , GSM 3 , I/O 4 , Maintenance 5 and etc. FMC003 has one user editable profile, which can be loaded and saved to the device. After any modification of configuration the changes need to be saved to device using Save to device button. Main buttons offer following functionality:

| Load from device – loads configuration from device.
---|---
| Save to device – saves configuration to device.
| Load from file – loads configuration from file.
| Save to file – saves configuration to file.
| Update firmware – updates firmware on device.
| Read records – reads records from the device.
| Reboot device – restarts device.
| Reset configuration – sets device configuration to default.

Most important configurator section is GPRS – where all your server and GPRS settings6 can be configured and Data Acquisition7 – where data acquiring parameters can be configured. More details about FMC003 configuration using Configurator can be found in our Wiki8.

QUICK SMS CONFIGURATION

Default configuration has optimal parameters present to ensure best performance of track quality and data usage.
Quickly set up your device by sending this SMS command to it:

Note: Before SMS text, two space symbols should be inserted.

GPRS SETTINGS:

2001 – APN 1
2002 – APN username (if there are no APN username, empty field should be left)
2003 – APN password (if there are no APN password, empty field should be left)
SERVER SETTINGS:
2004 – Domain
2005 – Port
2006 – Data sending protocol (0 – TCP, 1 – UDP)

DEFAULT CONFIGURATION SETTINGS
MOVEMENT AND IGNITION DETECTION:

|
---|---
VEHICLE MOVEMENT
will be detected by accelerometer| IGNITION
will be detected by vehicle power voltage
between 13,2 – 30 V
DEVICE MAKES A RECORD ON STOP IF:| RECORDS SENDING TO SERVER:
---|---
|
1 HOUR PASSES
while vehicle is stationary and ignition is off| EVERY 120 SECOND
it is sent to the server If device has made a record

DEVICE MAKES A RECORD ON MOVING IF ONE OF THESE EVENTS HAPPEN:

|
---|---
PASSES
300 seconds| VEHICLE DRIVES
100 meters
|
VEHICLE TURNS
10 degrees| SPEED DIFFERENCE
between last coordinate and current position is greater than 10 km/h

After successful SMS configuration, FMC003 device will synchronize time and update records to configured server. Time intervals and default I/O elements can be changed by using Teltonika Configurator or SMS parameters2.

MOUNTING RECOMMENDATIONS

CONNECTING THE DEVICE TO THE VEHICLE:
Find OBDII connector in your vehicle.

Most common OBDII connector locations.

LED INDICATIONS

NAVIGATION LED INDICATIONS

Behaviour	Meaning
Permanently switched on	GNSS signal is not received
Blinking every second	Normal mode, GNSS is working
Off	GNSS is turned off because: Device is not working or Device is in

sleep mode
Blinking fast constantly| Device firmware is being flashed

STATUS LED INDICATIONS

Behaviour	Meaning
Blinking every second	Normal mode
Blinking every two seconds	Sleep mode
Blinking fast for a short time	Modem activity
Off	Device is not working or Device is in boot mode

BASIC CHARACTERISTICS

Module

Name	MeiG SLM320-L16A, MeiG SLM320PE2C, Teltonika TM2500
Technology	LTE(CAT1)/2G(GSM/GPRS)/GNSS/BLUETOOTH

GNSS

GNSS	GPS, GLONASS, GALILEO, BEIDOU, SBAS, QZSS, DGPS, AGPS
Receiver	33 channel
Tracking sensitivity	-165 dBM
Accuracy	< 3 m
Hot start	< 1 s
Warm start	< 25 s
Cold start	< 35 s

Celluar

Technology	LTE CAT 1, GSM
2G bands	MeiG SLM320-PE2C: GSM: B2/B3/B5/B8

MeiG SLM320-L16A: GSM: B2/B3/ B5/B8
4G bands| MeiG SLM320-PE2C: MeiG SLM320PE2C LTE-FDD: B1/B3/B7/B8/
B20/B28 LTE-TDD:B38/B40/B41
MeiG SLM320-L16A: LTE FDD: B1/ B2/B3/B4/B5/B7/B8/B20/B28 LTETDD:B40
Data transfer| LTE: LTE FDD: Max 10Mbps (DL)/Max 5Mbps (UL)
LTE TDD: Max 8Mbps (DL)/Max 2Mbps (UL)
GSM: GPRS: Max 85.6Kbps (DL)/Max 85.6Kbps (UL)
Transmit power| Class 4 for GSM850/900: 23±2dBm
Class 1 for GSM1800/1900: 20±2dBm
Class 3 for LTE-TDD: 23±2.7dBm
Class 3 for LTE-FDD: 23±2.7dBm
Data support| SMS (text/data)

Power

Input voltage range	10 – 30 V DC with overvoltage protection
Back-up battery	170 mAh Li-Po battery 3.7 V (0.63 Wh)
Internal fuse	3A, 125V
Power Consumption	At 12V < 6.5 mA (Ultra Deep Sleep)

At 12V < 8 mA (Deep Sleep)
At 12V < 13 mA (Online Deep Sleep)
At 12V < 16.3 mA (GPS Sleep)
At 12V < 31 mA (nominal with no load)
At 12V < 0.25A Max. (with full Load / Peak

Bluetooth

Specification	4.0 + LE
Supported peripherals	Temperature and Humidity sensor 1 , Inateck Barcode

Scanner, Universal BLE sensors support

OBD Interface

Data	HS CAN, MS CAN, SW CAN, K-line
Data reading	OEM Fuel level, odometer and up to 32 vehicle onboard

parameters,
supported OBD protocols: ISO 9141-2 (5 baud init, 10.4 kbaud)
ISO 14230-4 KWP (5 baud init, 10.4 kbaud)
ISO 14230-4 KWP (fast init, 10.4 kbaud)
ISO 15765-4 CAN (11 bit ID, 250 kbaud)
ISO 15765-4 CAN (11 bit ID, 500 kbaud)
ISO 15765-4 CAN (29 bit ID, 250 kbaud)
ISO 15765-4 CAN (29 bit ID, 500 kbaud)
ISO 14229 (UDS) J2819 (VW TP2.0

Interface

Connection	OBDII socket
GNSS antenna	Internal High Gain
GSM antenna	Internal High Gain
USB	2.0 Micro-USB
LED indication	2 status LED lights
SIM	Micro-SIM
Memory	128MB internal flash memory

Physical Specification

Dimensions	67,2 x 49,6 x 25 mm (L x W x H)
Weight	63 g

Operating Environment

Operating temperature (without battery)	-40 °C to +85 °C
Storage temperature (without battery)	-40 °C to +85 °C
Operating humidity	5% to 95% non-condensing
Operating Temperature (with battery)	-20C to + 40C
Ingress Protection Rating	IP41
Battery charge temperature	0 °C to +45 °C
Battery discharge temperature	-20 °C to +60 °C
Battery storage temperature	-20 °C to +45 °C for 1 month

-20 °C to +35 °C for 6 months

Features

Sensors	Accelerometer
Scenarios	[Green Driving](https://wiki.teltonika-

gps.com/view/FMC003_Features_settings#Eco.2FGreen_Driving), Over Speeding detection, Jamming detection,
GNSS Fuel Counter, Excessive Idling detection, Unplug detection, Towing detection, Crash detection, Auto Geofence, Manual Geofence, Trip 2
Sleep modes| GPS Sleep, Online Deep Sleep, Deep Sleep, Ultra Deep Sleep3
Configuration and
firmware update| FOTA Web4 , FOTA 5 , Teltonika Configurator6 (USB, Bluetooth), FMBT mobile application 7 (Configuration)
SMS| Configuration, Events, Debug
GPRS commands| Configuration, Debug
Time
Synchronization| GPS, NITZ, NTP
Fuel monitoring| OBDII
Ignition detection| Accelerometer, External Power Voltage, Engine RPM

2 wiki.teltonika-gps.com/view/FMC003_Features_settings
3 wiki.teltonika- gps.com/view/FMC003_Sleep_modes#Deep_Sleep_mode
4 wiki.teltonika-gps.com/view/FOTA_WEB
5 wiki.teltonika-gps.com/view/FOTA
6 wiki.teltonika-gps.com/view/Teltonika_Configurator
7 wiki.teltonika-gps.com/view/FMBT_Mobile_application

SAFETY INFORMATION

This message contains information on how to operate FMC003 safely. By following these requirements and recommendations, you will avoid dangerous situations. You must read these instructions carefully and follow them strictly before operating the device!

The device uses SELV limited power source. The nominal voltage is +12 V DC. The allowed voltage range is +10…+30 V DC.
To avoid mechanical damage, it is advised to transport the device in an impact-proof package. Before usage, the device should be placed so that its LED indicators are visible. They show the status of device operation.
Before unmounting the device from vehicle, ignition MUST be OFF.

| Do not disassemble the device. If the device is damaged, the power supply cables are not isolated or the isolation is damaged, DO NOT touch the device before unplugging the power supply.
---|---
| All wireless data transferring devices produce interference that may affect other devices which are placed nearby.
| Please consult representatives of your vehicle model regarding OBDII location on your vehicle.
In case you are not sure about proper connection, please consult qualified personnel.
| The programming must be performed using a PC with autonomic power supply.
| Installation and/or handling during a lightning storm is prohibited.
| The device is susceptible to water and humidity.
| Teltonika is not responsible for any harm caused by wrong cables used for connection between PC and FMC003
| WARNING! Do not use FMC003 device if it distracts driver or causes inconvenience due to OBDII placement. Device must not interfere with driver.
| Battery should not be disposed of with general household waste. Bring damaged or worn-out
batteries to your local recycling center or dispose them to battery recycle bin found in stores.

CERTIFICATION AND APPROVALS

This sign on the package means that it is necessary to read the User‘s Manual before your start using the device. Full User‘s Manual version can be found in our Wiki1.
1 wiki.teltonika-gps.com/index.php?title=FMC003
The RoHS 1 is a directive regulating the manufacture, import and distribution of Electronics and Electrical Equipment (EEE) within the EU, which bans from use 10 different hazardous materials (to date).
1 wiki.teltonika-gps.com/view/FMC003_RoHS

CHECK ALL CERTIFICATES
All newest certificates may be found in our Wiki 2.
2 wiki.teltonika-gps.com/view/FMC003Certification%26_Approvals

This sign on the package means that all used electronic and electric equipment should not be mixed with general household waste.
For more information, see the ANATEL website www.anatel.gov.br
This equipment is not entitled to protection against harmful interference and must not cause interference in duly authorized systems.

WARRANTY

TELTONIKA guarantees its products to be free of any manufacturing defects for a period of 24 months. With additional agreement we can agree on a different warranty period, for more detailed information please contact our sales manager.
Contact us teltonika-gps.com/about-us/contacts
All batteries carry a reduced 6 month warranty period.
If a product should fail within this specific warranty time, the product can be:

Repaired
Replaced with a new product
Replaced with an equivalent repaired product fulfilling the same functionality
TELTONIKA can also repair products that are out of warranty at an agreed cost.

WARRANTY DISCLAIMER

TELTONIKA PRODUCTS ARE INTENDED TO BE USED BY PERSONS WITH TRAINING AND EXPERIENCE. ANY OTHER USE RENDERS THE LIMITED WARRANTIES EXPRESSED HEREIN AND ALL IMPLIED WARRANTIES NULL AND VOID AND SAME ARE HEREBY EXCLUDED. ALSO EXCLUDED FROM THIS LIMITED WARRANTY ARE ANY AND ALL INCIDENTAL OR CONSEQUENTIAL DAMAGES INCLUDING BUT NOT LIMITED TO, LOSS OF USE OR REVENUE, LOSS OF TIME, INCONVENIENCE OR ANY OTHER ECONOMIC LOSS.
More information can be found at teltonika-gps.com/warranty-repair