DrayTek VigorSwitch G2540xs L2+ Managed Switch User Guide

DrayTek VigorSwitch G2540xs L2+ Managed Switch

Package content

If any of these items is found missing or damaged, please contact your local supplier for replacement.

Panel Explanation

LED Status               Explanation

Monitor

| On (Red)| An alert for system failure due to overheating or wrong voltage.
Off| The device is in normal condition and running normally.

SYS

| On (Green)| The switch finishes system booting and the system is ready.
Blinking (Green)| The switch is powered on and starts system booting.
Off| The power is off or the system is not ready / malfunctioning.
PWR| On (Green)| The device is powered on and running normally.
Off| The device is not ready or is failed.

Port 1 ~ 48 (GbE RJ45)

| On (Green)| The device is connected with 1000Mbps.
On (Amber)| The device is connected with 10/100Mbps.
Blinking| The system is sending or receiving data through the port.
Off| The port is disconnected or the link is failed.

Port 49 ~ 54 (SFP+)

| On (Green)| The device is connected with 1000Mbps.
On (Blue)| The device is connected with 10Gbps.
Blinking| The system is sending or receiving data through the port.
Interface                                Description
RST| Restore the default settings.
Port 1 ~ 48| Port 1 to Port 48 can be used for Ethernet connection.
Port 49 ~ 54 (SFP+)| Port 49 to Port 54 are used for 10G/1000M fiber connection.
Console| Used to perform telnet command control.
 | Power inlet for AC input (100~240V/AC, 50/60Hz).

Hardware Installation

This section will guide you to install the switch through hardware connection and configure the switch’s settings through web browser.

Network Connection
Before starting to configure the switch, you have to connect your devices correctly. Use the Ethernet cable(s) to connect None-PoE devices to the Vigor switch. All device ports are in the same local area network.

Rack Mounted Installation

The switch can be installed easily by using rack mount kit.

1. Fasten the rack mount kit on both sides of the VigorSwitch using specific screws.
2. Then, install the VigorSwitch (with rack mount kit) on the 19-inch chassis by using other four screws.

Software configuration

Before using the switch, perform the following steps:

1. Set up a physical path between the configured the switch and a PC by a qualified UTP Cat. 5e cable with RJ-45 connector. If a PC directly connects to the switch, you have to setup the same subnet mask for PC and the switch. Default values of the managed switch are listed as follows.
   IP Address| 192.168.1.224
   ---|---
   Subnet Mask| 255.255.255.0
   DHCP Client| Enabled (On)
   Username| admin
   Password| admin
2. After configuring correct IP address on your PC, open your web browser and access switch’s IP address.

The home page of VigorSwitch will be shown as below:

Customer Services

If the switch cannot work correctly after trying many efforts, please contact your dealer for further help right away. For any questions, please feel free to send e-mail to support@draytek.com.

GPL Notice

This DrayTek product uses software partially or completely licensed under the terms of the GNU GENERAL PUBLIC LICENSE. The author of the software does not provide any warranty. A Limited Warranty is offered on DrayTek products. This Limited Warranty does not cover any software applications or programs.
To download source codes please visit:http://gplsource.draytek.com

GNU GENERAL PUBLIC LICENSE: https://gnu.org/licenses/gpl-2.0

Version 2, June 1991
For any question, please feel free to contact DrayTek technical support at support@draytek.com for further information.

Be a Registered Owner

Web registration is preferred. You can register your Vigor router via https://myvigor.draytek.com.

Firmware & Tools Updates
Due to the continuous evolution of DrayTek technology, all switches will be regularly upgraded. Please consult the DrayTek web site for more information on newest firmware, tools and documents. https: / / www.draytek.com

EU Declaration of Conformity

We DrayTek Corp. , office at No.26, Fushing Rd, Hukou, Hsinchu Industrial Park, Hsinchu 303, Taiwan, declare under our sole responsibility that the product

• Product name: 48+6 ports 10G up-link Switch
• Model number: VigorSwitch G2540xs
• Manufacturer: DrayTek Corp.
• Address: No.26, Fushing Rd, Hukou, Hsinchu Industrial Park, Hsinchu 303, Taiwan.

All rights reserved. This publication contains information that is protected by copyright. No part may be reproduced, transmitted, transcribed, stored in a retrieval system, or translated into any language without written permission from the copyright holders. The following trademarks are used in this document:

Trademarks

• Microsoft is a registered trademark of Microsoft Corp.
• Windows 8, 10, 11 and Explorer are trademarks of Microsoft Corp.
• Apple and Mac OS are registered trademarks of Apple Inc.
• Other products may be trademarks or registered trademarks of their respective manufacturers.

Safety Instructions

• Read the installation guide thoroughly before you set up the switch.
• The switch is a complicated electronic unit that may be repaired only be authorized and qualified personnel. Do not try to open or repair the switch yourself.
• Do not place the switch in a damp or humid place, e.g. a bathroom.
• The switch should be used in a sheltered area, within a temperature range of 0 to +45 Celsius.
• Do not expose the switch to direct sunlight or other heat sources. The housing and electronic components may be damaged by direct sunlight or heat sources.
• Do not deploy the cable for LAN connection outdoor to prevent electronic shock hazards.
• Keep the package out of reach of children.
• When you want to dispose of the switch, please follow local regulations on conservation of the environmen

Warranty

We warrant to the original end user (purchaser) that the device will be free from any defects in workmanship or materials for a period of two (2) years from the date of purchase from the dealer. Please keep your purchase receipt in a safe place as it serves as proof of date of purchase. During the warranty period, and upon proof of purchase, should the product have indications of failure due to faulty workmanship and/or materials, we will, at our discretion, repair or replace the defective products or components, without charge for either parts or labor, to whatever extent we deem necessary tore- store the product to proper operating condition. Any replacement will consist of a new or re-manufactured functionally equivalent product of equal value, and will be offered solely at our discretion. This warranty will not apply if the product is modified, misused, tampered with, damaged by an act of God, or subjected to abnormal working conditions. The warranty does not cover the bundled or licensed software of other vendors. Defects which do not significantly affect the usability of the product will not be covered by the warranty. We reserve the right to revise the manual and online documentation and to make changes from time to time in the contents hereof without obligation to notify any person of such revision or changes.

Regulatory Information

Federal Communication Commission Interference Statement This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
•  Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

1. This device may not cause harmful interference, and
2. This device may accept any interference received, including interference that may cause undesired operation.

Caution: Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
More update, please visit www.draytek.com.

References

• Home | DrayTek
• GNU General Public License v2.0 - GNU Project - Free Software Foundation
• MyVigor - DrayTek
• Home | DrayTek

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>