beamZ 153.325 BMS24 LED Mini Stroboscope Light User Manual

153.325 BMS24 LED Mini Stroboscope Light
User Manual

SAFETY INSTRUCTIONS

WARNING! Before carrying out any operations with the unit, carefully read this instruction manual and keep it with care for future reference. It contains important information about the installation. usage and maintenance of the unit.

• Unpack and check carefully that there is no transportation damage before using the unit
• Please read these instructions carefully and follow the instructions.
• Observe all safety warnings. Never remove safety warnings or other information from the equipment
• Be sure thane ventilation slots are blocked: otherwise the unit will overheated.

WARNING! Before connecting the equipment to the power outlet, first verify that the mains voltage and Frequency match the values specified on the equipment. IF the  equipment has a voltage selection switch, connect the equipment to the power outlet only if the equipment values and the mains power values match. If the included power cord or power adapter does not fit in your wall outlet, contact your electrician.

• After connecting the unit, check all cables in order to prevent damage or accidents, e.g. due to tripping hazards.
• Make sure that the power cord is never crimped or  damaged. Check the unit and the power cord from time to time.
• Always disconnect power from the mains, when unit is not used or before cleaning! Only handle the power cord by the plug. Never pull out the plug by tugging the  power cord.
• Unplug the power cord and power adapter from the power outlet if there is a risk of a lightning strike or before extended periods of disuse.
• Donor switch the unit on and off in short intervals.
• Do not connect the unit to a dimmer pack.
• Install the unit ina well ventilated place.
• Never place any material over the lens.
• Never let the sunlight lights directly to the Front lens . even when the unitis not working.
• Always allow Free air space of at least SO cm around the unit for ventilation.
• Make sure that the area below the installation place is blocked when rigging, derigging or servicing the unit.
• For mounting height >100 cm. always fix the unit with an appropriate safety-rope. Fix the safety-rope at the correct foxation points only. The safely-rope must never be  fixed at the transport handles!
• Never look directly at the light beam. Please note that fast changes in lighting. e. g. flashing light, may trigger epileptic seizures in photosensitive persons or persons with  epilepsy.
• This unit is not designed For permanent operation. Consistent operation breaks will ensure that the unit will serve you For a long time without defects.

WARNING! If the power cord of the unit is equipped with an earthing contact, then it must be connected to an outlet with a protective ground.
Never deactivate the protective ground of a power cord.

• Make sure that the unit is not exposed to extreme heat, moisture or dust.
• Clean the unit using a dry cloth.
• Do not touch the unit bare-handed during its operation (housing becomes very ho. Allow the unit to cool for at least 5 minutes before handling.
• This unit is designed exclusively for indoor use. do not use this equipment in the immediate vicinity of Fluid [does not apply to special outdoor equipment – in this case.  observe the special instructions noted below). Do not expose this unit to flammable materials. Fluids or gases.
• If the unthaws been exposed to drastic temperature Fluctuation [e.g. after transportation), do not switch it on immediately. The arising condensation water might damage your unit. Leave the unit switched off until itches reached room temperature.
• Never attempt to bypass the thermostatic switch or fuses.
• Donta dismantle or modify the unit.
• For replacement use fuses/bulb of same type and rating only.
• Repairs, servicing and electric connection must be carried out by a qualified technician.
• The ambient temperature must always be between -5° Candy +45°C.
•  IF this unit is operated in any other way, than the one described in this manual, the product may suffer damages and the warranty becomes void.
• Plastic bags must be kept out of reach of children.
• Unit must be installed out of the reach of children. Never leave the unit running unattended.

**** This symbol on the product or on its packaging indicates that this product shall not be treated as household waste. Instead it shall be handed over to the applicable  collection point for the recycling of electrical and electronic equipment.
By ensuring this product is disposed of correctly. you will help prevent potential negative consequences for the environment and human health, which could otherwise be caused by inappropriate waste handling of this product. The recycling of materials will help to conserve natural resources. For more detailed information about recycling  of this product, please contact your local Civic Office, your household waste disposal service or the shop where you purchased the product.

UNPACKING INSTRUCTION

CAUTION! Immediately upon receiving the product. carefully unpack the carton, check the contents to ensure that all parts are present. and have been received in good condition. Notify the shipper immediately and retain packing material fo’ inspection if any parts appear damage From shipping or the package itself shows signs of mishandling. Save the package and all packing materials. In the event that the product must be returned to the factory. it is important that the product be returned in the original factory box and packing. If the unit has been exposed to drastic temperature fluctuation (e.g. after transportation). do not switch it on immediately. The arising condensation water might damage your unit. Leave the unit switched off until it has reached room temperature.

POWERSUPPLY

The label on the backside of the unit indicates the mains voltage to which it must be connected. Check that the mains voltage corresponds to this. Any other voltage than the one indicated may cause irreparable damage to the unit The unit must also be connected directly to the mains voltage and no dimmer or adjustable power supply may be used. WARNING! Always connect the unit to a protected circuit (circuit breaker or fuse). Make sure the unit has a n appropriate electrical ground to avoid the risk of electrocution or fire.

RISK OF INJURIES

CAUTION! Stroboscope effects may cause epileptic seizures in sensitive people!
To guard against risks From epileptic seizure:

• Do not operate the fixture near stairways. in corridors or near public exits.
• Provide advance notice that strobe lighting is in use. Display advisory notices at the point of ticket sales. on tickets if possible, in the program. and at the entrance(s) to the venue.
• Avoid extended periods of continuous flashing. particularly at frequencies of 10 to 20 flashes per second. At flash rates below 5 flashes per second. it is estimated that only 5% of flicker-sensitive persons will beat risk of seizure.
• Make sure that personnel at the venue are trained in the care of a person who is having an epileptic seizure and able to provide care if necessary.
• If strobes are in use and a person has a seizure, switch the strobes off immediately.
• Mount the fixture as high above head height as practicable.

INSTALLATION

The installation construction should be able to support a minimum point load of 10 times the weight of the device.

• The installation must always be secured with a secondary attachment e.g. a safety cable
• Never stand directly below the device when it is being mounted removed or serviced. Have a qualified technician check the device once a year and once before you bring it into service.
• Overhead mounting requires extensive experience: calculating workload limits. determining the installation material to be used Have the material and the device itself checked regularly. Do not attempt to install the device yourself if you ack these qualifications as improper installation may result in injuries.
• The installation has to be approved by an expert before the device is taken into service.
• The glass pane has to be replaced when it is damaged. When carrying out any installation. always comply European and national guidelines concerning rigging. truss and all other safety issues. Always let the installation checked out by an authorized dealer !

MAINTENACE

This unit is virtually maintenance-free. but you should check the unit regularly for mechanical and electrical aspects. Assess the operating environment and establish an inspection and cleaning schedule that follows the guidelines below:

• Disconnect the unit from the power supply and allow it to cool completely before inspecting and cleaning.
• Check that the screws and bolts used to install the unit are securely tightened and free from corrosion.
• Check the housing. fixing points and installation points. they must not show any signs of deformation wear or fatigue.
• Check the mechanically moving parts. these must not show any signs of wear or fatigue.
• Check the electrical power and signal cables, they must not show any damage or fatigue.
• Do not use solvents. abrasives or other aggressive products to clean the unit
• Wipe the unit and clean the glass plate with a soft clean. lint-free cloth moistened with a weak cleaning solution Place the solution on the cloth and not on the surface to be cleaned. Avoid rubbing glass surfaces.
• Dry the unit. connectors and contacts with a soft clean lint-free cloth or low-pressure compressed air before re-powering the unit.

is a leading developer of lighting products, including intelligent DMX moving heads, wireless battery operated DMX effects, static washes, sound-activated club effects, strobes & backlights, LED lighting, fog and special effects machines, lasers and indoor and outdoor architectural lighting, as well as lighting controllers and protective bags.

BEAMZLIGHTING.COM

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>