Palmer PWT12IEC Universal 12 Fold Power Supply Unit User Manual
- June 9, 2024
- Palmer
Table of Contents
USER MANUAL
5 Year Guarantee
PWT12IEC
Universal 12-fold power supply unit for the power supply of effect devices
INTENDED USE
This product is a power supply unit for effect units. Any other use and the
use of the product outside the specified technical data and operating
conditions are considered improper use!
Liability for damage and third-party damage to persons and property due to
inappropriate use is excluded!
The product is not suitable for:
- Persons (including children) with limited physical, sensory or mental abilities or lack of experience and knowledge.
- Children (children must be instructed not to play with the device).
SAFETY INSTRUCTIONS
- Please read these instructions carefully.
- Keep all information and instructions in a safe place.
- Follow the instructions.
- Use the device in the prescribed manner only.
- Do not open the device and do not perform any modifications.
CHOKING HAZARD! KEEP OUT OF THE REACH OF CHILDREN! THE PRODUCT CONTAINS SMALL PARTS AND PACKAGING MATERIAL THAT CAN BE SWALLOWED! PLASTIC BAGS MUST BE KEPT OUT OF THE REACH OF CHILDREN!
INTRODUCTION
The power supply unit with 12 isolated and one non-isolated DC output also has a USB-A and a USB-C port that can be used to charge smartphones and tablets. The power supply of the unit is not provided by an external power supply unit, but by a standard IEC power cable with IEC connector. All DC outputs are wired with positive pole outside and negative pole inside.
INCLUDED
Remove the product from the packaging and remove all packing material. Please
check the completeness and integrity of the delivery and notify your
distribution partner immediately after purchase if the delivery is not
complete or if it is damaged.
The packaging includes:
- 1 x PWT12IEC power supply unit
- 1 x Mains cable with IEC appliance plug
- 5 x DC cable 30 cm
- 5 x DC cable 60 cm
- 5 x DC cable 90 cm
- 1 set of self-adhesive rubber feet
- Operating instructions
CONNECTIONS AND OPERATING ELEMENTS
-
AC INPUT
IEC connection for the power supply of the unit. A suitable mains cable is included in the scope of delivery. -
POWER
Rocker switch for switching the device on and off. The switch has an indicator light. This lights up as soon as the unit is correctly connected to the power supply and switched on. -
DC OUTPUT
Non-isolated 9 V DC output with up to 2000 mA output current for effects units with high current requirements and external power supplies (e.g. PWT04) that do not require an isolated and filtered power supply. -
USB
One USB-C and USB-A port each with up to 18 watts total power for charging smartphones, tablets and the like. -
OUTPUT 1 AND 2
Two isolated DC voltage outputs with potentiometers for a continuously adjustable output voltage from 6 V to 18 V and up to 250 mA output current. Always set the required voltage BEFORE connecting the corresponding effect device. -
OUTPUT 3 TO 6
Four isolated DC outputs with 9 V output voltage and up to 100 mA output current each. -
OUTPUT 7 TO 10
Four isolated DC outputs with 9 V output voltage and up to 250 mA output current each. -
OUTPUT 11 AND 12
Two isolated DC outputs with 9 V output voltage and up to 500 mA output current each.
CAUTION! Material damage due to reverse polarity!
Make sure that the polarity of the DC voltage input of the corresponding
effect unit corresponds with matches the polarity of the DC voltage outputs of
the power supply unit (positive pole outside, negative pole inside). An effect
unit with a DC input of reversed polarity can cause a malfunction when
connected to the damage to this power supply unit.
CAUTION! Property damage due to overvoltage!
Make sure that the output voltage of the power supply corresponds to the
voltage required by the effect unit Input voltage corresponds. An effect unit
can be damaged by overvoltage.
CAUTION! Material damage due to DC voltage at the AC voltage input!
Do not connect any effect device that is intended for an AC voltage as power
supply, to this power supply unit. In individual cases, this could damage the
effect unit and / or the power supply unit.
MOUNTING
The housing of the power supply unit has mounting holes in the base plate and the side panels (fig. A) so that the power supply unit can be securely fastened to a pedalboard (e.g. with cable ties).
TECHNICAL DATA
GENERAL
| Product number | PWT12IEC |
|---|---|
| Product type | Power Supplies |
| Input voltage | AC 100 – 240 V |
| Individually isolated DC outputs | 12 |
| Output 1-2 | 6 – 18 V (250 mA max) |
| Output 3-6 | 9 V (100 mA max) |
| Output 7-10 | 9 V (250 mA max) |
| Output 11-12 | 9 V (500 mA max) |
| Non-isolated DC output | 9 V (2000 mA max) |
| Output connections | 2.1 x 5.5 mm |
| Output voltage: | 6 V – 18 V |
| Max. Output power | 30.6 W (output 1 – 12) |
| Max. Power consumption | 77 W |
| Individually isolated outputs | yes |
| Polarity | Centre-negative |
| USB-C / USB-A output power | 18 W max. |
| Display indicators | Power |
| Operating controls | Mains switch, output voltage selector |
| Depth | 93 mm |
| Width | 168 mm |
| Height | 42 mm |
| Weight | 0,54 kg |
| Accessories | Mains cable, 15x DC cable (30 / 60 / 90 cm), 4x rubber feet |
| Noise | < 40 µV (output 1 – 12) |
| Ambient temperature for operation | 0° to 40°C |
| Relative air humidity | <80%, non-condensing |
DISPOSAL
PACKAGING:
- Packaging can be fed into the reusable material cycle using the usual disposal methods.
- Please separate the packaging in accordance with disposal laws and recycling regulations in your country.
DEVICE:
-
This device is subject to the European Waste Electrical and Electronic Equipment Directive in the currently valid version. WEEE Waste Electrical and Electronic Equipment Directive.
Old appliances do not belong in household waste. The old device must be disposed of via an approved disposal company or a municipal disposal facility. Please observe the applicable regulations in your country! -
Observe all disposal laws applicable in your country.
-
As a private customer, you can obtain information on environmentally friendly disposal options from the seller of the product or the appropriate regional authorities.
BATTERIES:
- Batteries should not be disposed of in house hold waste. Batteries and rechargeable batteries must be disposed of via an approved disposal company or a municipal disposal facility.
- Observe all disposal laws applicable in your country.
- As a private customer, you can obtain information on environmentally friendly disposal options from the seller of the product or through the relevant regional authorities.
- Devices with batteries that cannot be removed by the user must be taken to a collection point for electrical appliances.
MANUFACTURER’S DECLARATIONS
Manufacturer’s warranty & limitation of liability
Adam Hall GmbH
Adam-Hall-Str. 1
61627, Neu-Anspach, Germany
Email: Info@adamhall.com / +49 (0)6081 / 9419-0.
Our current warranty conditions and limitation of liability can be found at:
https://cdn-shop.adamhall.com/media/pdf/Manufacturers-Declarations-
PALMER_DE_EN_ES_FR.pdf
Contact your distribution partner for service.
CE CONFORMITY
Adam Hall GmbH hereby confirm that this product meets the following guidelines
(where applicable):
Low-Voltage Directive (2014/35/EU)
EMC Directive (2014/30/EU)
RoHS (2011/65/EU)
RED (2014/53/EU)
EC DECLARATION OF CONFORMITY
Declarations of conformity for products that are subject to the LVD, EMC, RoHS
Directives, can be requested at info@adamhall.com.
Declarations of conformity for products that are subject to the RED Directive
can be downloaded at
www.adamhall.com/compliance/ .
FCC STATEMENT
This device complies with Part 15 of the FCC Rules.
Operation is subject to the following two conditions:
- This device may not cause harmful interference, and
- This device must accept any interference received, including interference that may cause undesired operation
UKCA- CONFORMITY
Hereby, Adam Hall Ltd. declares that this product meets the following
guidelines (where applicable)
Electrical Equipment (Safety) Regulations 2016
Electromagnetic Compatibility Regulations 2016 (SI 2016/1091)
The Restriction of the Use of Certain Hazardous Substances in Electrical and
Electronic Equipment Regulation 2012 (SI 2012/3032) Radio Equipment
Regulations 201 7(SI 2016/2015)
UKCA- DECLARATION OF CONFORMITY
Products that are subject to Electrical Equipment(Safety)
Regulation 2016, EMC Regulation 2016 or RoHS Regulation can be requested at
info@adamhall.com.
Products that are subject to the Radio Equipments Regulations 2017
(SI2017/1206) can be downloaded from
www.adamhall.com/compliance/
SUBJECT TO MISPRINTS AND ERRORS, AS WELL AS TECHNICAL OR OTHER MODIFICATIONS!
Documents / Resources
|
Palmer PWT12IEC Universal 12 Fold Power Supply
Unit
[pdf] User Manual
PWT12IEC, PWT12IEC Universal 12 Fold Power Supply Unit, Universal 12 Fold
Power Supply Unit, 12 Fold Power Supply Unit, Power Supply Unit
---|---
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>