BRANDMOTION FVMR-1170 FullVUE Replacement Rear-View Mirror-Monitor Instruction Manual

BRANDMOTION FVMR-1170 FullVUE Replacement Rear-View Mirror-Monitor

Product Information: Rear Camera Mirror for RAM 1500 (2009-2018) & Heavy

Duty (2010-Current)

The Rear Camera Mirror for RAM 1500 (2009-2018) & Heavy Duty (2010-Current) is a kit that includes all necessary components to install a rearview camera onto your vehicle’s mirror. The kit includes a FullVUE mirror, power harness, camera harness, and rear camera. The rearview camera provides a clear view of what’s behind your vehicle, making it easier and safer to park, reverse, and maneuver in tight spaces.

The installation process requires basic tools such as a wrench, wire strippers, wire cutters, electrical tape, screwdriver, panel removal tool, zip ties, and socket set. The installation time varies between 45-75 minutes.

Product Usage Instructions

Part 1: Installing the Mirror

1. Remove the old mirror from the mount on the windshield as per the manufacturer’s directions. Be sure to use the proper removal tool if required.
2. Install new mirror onto the D-tab and tighten it with a Phillips screwdriver. Take care not to overtighten. Overtightening could result in damage to your windshield.

Part 2: Connecting the Power Harness

1. Connect the power harness to the plug on the mirror.
2. Route the harness across the top of the headliner, along the windshield, and down the A-pillar, and to the desired location in the kick panel.
3. Ensure that the harness will not be pinched when trim panels are replaced.

Part 3: Wiring the FullVUE Mirror

1. Connect the RED wire from the mirror harness to 12-volt accessory power.
2. Connect the YELLOW wire from the mirror harness to 12-volt constant power.
3. Connect the BLACK wire to a solid ground. Chassis ground in the kick panel is recommended.

Part 4: Function Test of the FullVUE Mirror

1. Turn the vehicle ignition on and see if you are seeing the front camera displayed on the screen. Turn off the ignition and the mirror will power down.

Part 5: Assembling the Bezel

1. Attach the thick foam gasket to the back side of the bezel or to the light. Whichever piece does not have a foam gasket from the factory. Note: The cable for the camera must go through the channel of the bezel before the foam is put overtop.
2. Put the foam side of the bezel against the vehicle.
3. Connect the rear camera harness to the camera. Make sure to line up the arrows on the connectors.

Part 6: Running Wires

1. Connect the 9m camera harness to the mirror harness at the connection by the mirror.
2. Run the 9m camera harness from the FullVUE Mirror through the headliner toward the brake light.
3. Pull the video connector of the 9m camera harness through the grommet to the outside of the cab.
4. Connect the 9m camera harness to the camera. Make sure to line up the arrows on the connectors.

Part 7: Disassembly

1. Use a Phillips screwdriver to remove the screws on either side of the brake light.
2. Pull the brake light out from the cab. Be careful not to damage the foam gasket around the opening.
3. Disconnect the power connector from the light.

If you have any questions or need technical support during installation, please call the Brandmotion technical support line at 734-619-1250 or visit their website for assistance.

Recommended Tools

Difficulty Level

Install Time

Kit Contents

Components for installing the FVMR-1170 Kit Contents:
FullVUE® Mirror & Harness
3rd Brake Light Bezel & Camera
9m Camera Harness

Installation of the FullVUE® Mirror and wire connections

Part 1
Attaching the FullVUE® Mirror to the windshield

1. Remove the old mirror from the mount on the windshield as per the manufacturer’s directions. Be sure to use the proper removal tool if required.
2. Install new mirror onto the D-tab and tighten with a Phillips screwdriver.

Take care not to overtighten. Overtightening could result in damage to your windshield.

Part 2
Powering the FullVUE® Mirror

1. Connect the power harness to the plug on the mirror. Route the harness across the top of the headliner, along the windshield, and down the A-pillar, and to the desired location in the kick panel.
2. Ensure that the harness will not be pinched when trim panels are replaced.

Part 3
Wiring the FullVUE Mirror

1. Connect the RED wire from the mirror harness to 12-volt accessory power.
2. Connect the YELLOW wire from the mirror harness to 12-volt constant power.
3. Connect the BLACK wire to solid ground. Chassis ground in the kick panel is recommended.

Part 4
Function test of the FullVUE Mirror

1. Turn the vehicle ignition on and see if you are seeing the front camera displayed on the screen. Turn off the ignition and the mirror will power down

Disassembly

Part 1
Removing the third brake light

1. Use a Phillips screwdriver to remove the screws on either side of the brake light
2. Pull the brake light out from the cab. Be Careful not to damage the foam gasket around the opening.
3. Disconnect the power connector from the light.

Running Wires

Part 1
Video Connector

1. Connect the 9m camera harness to the mirror harness at the connection by the mirror.
2. Run the 9m camera harness from the FullVUE Mirror through the headliner toward the brake light.
3. Pull the video connector of the 9m camera harness through the grommet to the outside of the cab.
4. Connect the 9m camera harness to the camera. Make sure to line up the arrows on the connectors

Assembly

Part 1
Assembling the Bezel

1. Attach the thick foam gasket to the back side of the bezel or to the light. Whichever piece does not have a foam gasket from the factory. Note: The cable for the camera must go through the channel of the bezel before the foam is put overtop
2. Put the foam side of the bezel against the vehicle.
3. Connect the rear camera harness to the camera. Make sure to line up the arrows on the connectors
4. Plug the brake light back into the cab plug
5. Put the screws through the hole of the light and insert the light into the bezel.
6. Use the screws that are showing through the bezel to line up with the screw holes of the vehicle. ( Be careful not to scratch the vehicle.)
7. Screw the assembly back together with the factory screws.

Adjustment

Part 1

1. If you need to change the camera’s pitch, gently bend the bracket until it reaches the desired view angle.

Questions? Call the Brandmotion technical support line at 734-619-1250

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>