aivituvin AIR10 Outdoor and Indoor Bunny Hutch Instruction Manual

aivituvin AIR10 Outdoor and Indoor Bunny Hutch

Product Information

The X AIR 10 is a product that is designed for small animals such as rabbits, guinea pigs, and chinchillas. It comes with a hutch and a pen, and is equipped with a lower tray and a folding metal feeder. The product also has a ramp for the animals to climb up and down. It has a roof hinge and a PVC curtain to protect the animals from rain and wind. The product has casters with brakes for easy movement and stability.

Product Usage Instructions

1. Before use, firmly secure all bolts, screws, and knobs.
2. Reconfirm that all bolts, screws, and knobs are secure every 90 days.
3. During initial assembly, fasten screws loosely. Do not fully tighten screws until the item is completely assembled.
4. Do not use or store this item in the proximity of open flame or flammable/combustible chemicals.
5. Be aware that some parts are heavy and have sharp edges. Moving parts can injure, crush, and cut.
6. If any parts are missing, broken, damaged, or worn, stop using this product until repairs are made and/or factory replacement parts are installed.
7. Do not use this item in a way inconsistent with the manufacturer’s instructions as this could void the product warranty.
8. Tools required for assembly include a Phillips screwdriver and a drill (recommended).
9. The assembly requires two persons and takes approximately 45 minutes.
10. To assemble the product, follow the instructions provided in the manual:
    • Attach Part A, Part B, and Part C using 6pcs of P2 screws.
    • Attach Part G to Part A and Part B using 4pcs of P2 screws.
    • Attach the pen Part D, Part E, and Part F using 4pcs of P2 screws.
    • Attach the pen to hutch using 2pcs of P1 screws. Repeat on the other side.
    • Slide in the tray Part J.
    • Put in 2pcs of Part H in the upward direction to separate the urine and poop. Then slide in the tray Part I.
    • Screw the feeder to Part C using 2pcs of P5 screws. Then put in the rabbit chewing toy P6.
    • Screw the ramp Part M to the bar on the Part G using 4pcs of P4 screws. Screw 2pcs of eye hook P8 on the front door of pen. Then hang with the front ramp. (Use only when needed)
    • Screw the roof hinge to the back using 3pcs of P4 screws on each side.
    • Screw the roof hinge P7, one side to the roof by P4x2 and the other side to the right panel by P4x2.
    • Attach the pen roof Part K using 4pcs of P2 screws. Stick PVC curtain P to the hutch door.
    • Screw two casters without brake Part Q to the front of hutch legs using P3x8. Screw two brake casters Part R to the back of hutch legs using P3x8.
11. If you have any questions or concerns about your product, contact the Aivituvin Help Center via service@aivituvin.com.
12. If you have received a faulty item or have any other problems, contact Aivituvin at service@aivituvin.com for a solution.

NOTICE
Please retain these instructions for future reference.

• Firmly secure all bolts,screws and knobs before use.
• Reconfirm that all bolts,screws,and knobs are secure every 90 days.
• Fasten screws loosely during initial assembly. Do not fully tighten screws until the item is completely assembled.
• Do not use or store this item in the proximity of open flame or flammable/combustible chemicals.
• Be aware that some parts are heavy and have sharp edges.
• Be aware that moving parts can injure,crush and cut.
• If any parts are missing,broken,damaged,or worn,stop using this product until repairs are made and/or factory replacement parts are installed.
• Do not use this item in a way inconsistent with the manufacturer’s instructions as this could void the product warranty.

TOOLS REQUIRED

HARDWARE

PARTS

PRODUCT ASSEMBLY

1. Attach Part A, Part B and Part C by 6pcs of P2 screws.

2. Attach Part G to Part A and Part B by 4pcs of P2 screws.

3. Attach the pen Part D, Part E, Part F by 4pcs of P2 screws.

4. Attach the pen to hutch by 2pcs of P1 screws.

5. Repeat on the other side.

6. Slide in the tray Part J

7. ① Put in 2pcs of Part H to be UPWARDS direction to seperate the urine & poop.
   ② Then slide in the tray Part I.

8. ① Screw the feeder to Part C by 2pcs of P5 screws.
   ② Then put in the rabbit chewing toy P6.

9. ① Screw the feeder to Part C by 2pcs of P5 screws.
   ② Then put in the rabbit chewing toy P6.

10. Screw the roof hinge to the back by 3pcs of P4 screws on each side.

11. Screw the roof hinge P7, one side to the roof by P4x2 the other side to the right panel by P4x2.

12. ① Attach the pen roof Part K by 4pcs of P2 screws.
    ② Stick PVC curtain “P” to the hutch door.

13. Screw two casters without brake Part Q to the front of hutch legs by P3x8.

14. Screw two brake casters Part R to the back of hutch legs by P3x8.

HELP CENTER

Question about your product? we’re here to help contact us via\

service@aivituvin.com

THANK YOU

• Thanks for your support to Aivituvin.
• Your satisfaction is our #1 priority.
• Once the items are received, opened, and deemed to be faulty or other problems.
• Pls contact us at service@aivituvin.com for the solution.
• We will feedback to you within 24 hours.
• If you are happy with the shopping ,welcome to share photos and thoughts with others .

WARNING
Manufacturer and seller expressly disclaim any and all liability for personal injury, property damage or loss, whether direct, indirect,or incidental, resulting from the incorrect attachment, improper use, inadequate maintenance,or neglect of this product.

www.aivituvin.com

References

• AIVITUVIN: Leading Brand in Wooden Pet House Industry! – Aivituvin

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>