aivituvin AIR66 Foldable Chicken Coop for 3 to 4 Chickens Instruction Manual

aivituvin AIR66 Foldable Chicken Coop for 3 to 4 Chickens

NOTICE
Please retain these instructions for future

• Firmly secure all bolts,screws and knobs before use.
• Reconfirm that all bolts,screws,and knobs are secure every 90 days.
• Fasten screws loosely during initial assembly. Do not fully tighten screws until the item is completely assembled.
• Do not use or store this item in the proximity of open flame or flammable/combustible chemicals.
• Be aware that some parts are heavy and have sharp edges.
• Be aware that moving parts can injure,crush and cut.
• If any parts are missing,broken,damaged,or worn,stop using this product until repairs are made and/or factory replacement parts are installed.
• Do not use this item in a way inconsistent with the manufacturer’s instructions as this could void the product warranty.

TOOLS REQUIRED

HARDWARE

PARTS

CARTON 1/2

PRODUCT ASSEMBLY

1. Expand the part of wire pen Part A .
2. Attach the Part C to the Part B by 2XP5 screws.
3. Attach the Part B to the left side of wire pen by 6XP6 screws.

1. Attach the support bar Part S to the corner of front and left side panel by 2X P5 screws.
2. Attach the ramp Part D to the Part B by 4XP7 screws.(Notice the direction of ramp)

1. Expand the part of wooden coop Part E.
2. Attach the connect bar Part F to the left & right side of coop by 12XP5 screws.(Please line up the same level of bottom edge)

Connect the wooden coop and wire pen with connecting bar by 2XP2 screws each side.

1. Slide in tray Part H in front.

2. Slide in support panel of middle ramp Part G in back.

3. Attach the Part G to side panel by 1 X P2 each sides.

4. Attach the ramp Part D to the support panel of middle ramp Part G by 4XP7 screws.(Notice the direction of ramp)

Insert 3PCS perches Part I into the slots inside left and right side panel of coop by 6XP4 screws.

Attach the nesting box,attach the Part K & Part J to the coop by 4XP1 bolts each sides.(Notice the direction of Part K & Part J )

Attach the side panel Part L to the Part K & Part J by 4XP3 screws each sides .

1. Drop in the bottom floor Part M to the nesting box each sides.
2. Insert the divider Part N into the slots of bottom floor each sides.

Attach the nesting box roof Part O to coop by 4XP7 screws each sides .

Attach the coop roof Part P by 8XP4 screws.

1. Attached PVC Waterproof Strip Part Q to the nesting box by 4XP6 screws each sides.
2. Put the Waterproof pvc P10 in the connection position of 2 roof cap to avoid the water leakage.
3. Ensure top roof panels line up with each other before screwing the cap 2XPart R by 8XP6 screws

1. Attach the latch P8 to the front tray by 6xP7 screws
2. Attach the spring latch P9 to the two front doors by 2xP7 screws each latches.
   (Notice the direction of latch)

Attach the spring latch P9 to the two back doors by 2xP7 screws each latches. (Notice the direction of latch) Notice
Read Before Assemble!

The below steps are for chicken coop & run combination by 4xP2 screws each sides. If you do only buy one chicken coop ,pls ignore the following.

Combination 1

Combination 2 Combination 3

WARNING
Manufacturer and seller expressly disclaim any and all liability for personal injury,property damage or loss,whether direct,indirect,or incidental,resulting from the incorrect attachment,improper use,inadequate miantenance,or neglect of this

www.aivituvin.com

References

• AIVITUVIN: Leading Brand in Wooden Pet House Industry! – Aivituvin

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>