guzzanti GZ-696 Kitchen Extractor Hood User Manual

guzzanti GZ-696 Kitchen Extractor Hood

Product Information
The GUZZANTI GZ-696 and GZ-699 are extractor hoods designed for domestic use in the kitchen. They are intended to extract polluted air from the space above the cooking appliance, reducing the
content of harmful products of incomplete combustion of natural gas and odors produced during cooking in the air, and preventing pollution of walls, ceiling, and furniture with grease and soot.
The appliance is manufactured from sheets of carbon steel with a decorative protective coating of powder paints, comes in widths of 600 / 900 mm, and has a diameter fan (turbine) with a grease
picking aluminum filter (included). It also has the option of upgrading with a carbon odor filter.
The extractor hood should be installed on the wall at a distance of 650-750mm above the electric cooker and at a distance of 750-850 mm above the gas cooker. It has a noise level of 52-70 / 50-69 dB,
depending on the model.

Product Usage Instructions

Prior to installing the extractor hood, carefully read the recommendations provided in the user manual for safe operation of the appliance. Save the user manual for future reference.
Before starting the operation (switching on) the appliance, it must be held at room temperature for at least two hours.
The appliance is intended for domestic use and household environments only. Using the extractor hood for purposes other than domestic use is forbidden and will lead to warranty cancellation.
Do not connect the extractor hood to the network of the electric cooker. Protect the electric cord from mechanical and thermal damage. While installing or conducting technical services, it is strictly forbidden to:

• Connect the extractor hood to the electricity network with a voltage and frequency that does not correspond to those specified in paragraph 2
• Use lighting lamps with a power output of more than 3 watts (LED)
• Carry out maintenance, replace lamps, remove filters, or clean the extractor hood without removing the plug from the mains socket
• Operate the extractor hood with an open fire source, open gas burners, or heating elements. Heating elements should always be covered with dishes
• Prepare food with the use of alcohol
• Leave the fryer unattended
• Operate the extractor hood with removed filters
• Connect the extractor hood to the electric network of the cooker or cut the socket of the electric cord while doing so

Dear customer!
Thank you for choosing the products of the brand ” GUZZANTI “. We put our best efforts so you were satisfied with your choice.

GENERAL INFORMATION

1. Prior to installing the extractor hood carefully read our recommendations, following which will provide safe work of the appliance. Save this User’s manual, as it contains answers to the questions which may arise later.
   BEFORE STARTING THE OPERATION (SWITCHING ON) THE APPLIANCE MUST BE HELD AT THE ROOM TEMPERATURE FOR AT LEAST TWO HOURS.

2. This appliance is intended for extraction of polluted air from the space above the cooking appliance, and intended for domestic use and the household environment only.
   USE OF THE APPLIANCE IN GOALS OTHER THAN DOMESTIC IS FORBIDDEN. THE RISK OF INJURY AND PROPERTY DAMAGE INCREASES IN CASE OF USE OF THE EXTRACTOR HOOD WITH PURPOSES OTHER THAN INTENDED, WHAT WILL LEAD TO WARRANTY CANCELLATION.

3. Use of the extractor hood decreases the content of harmful products of incomplete combustion of natural gas, as well as odors produced during cooking in the air, and prevents pollution of walls, ceiling, and furniture with grease and soot.

4. The appliance is an air purifying device of the exhaust type with a diameter fan (turbine), completed with a grease picking aluminum filter (included) and has the option of upgrading with a carbon odor filter. It is manufactured from sheets of carbon steel with a decorative protective coating of powder paints – 600 / 900 mm in width.

5. Depending on the installation scheme over the cooker, the extractor hood can work in two variants:
   – in the mode of air extraction into the stationary ventilation shaft (chimney) of the kitchen using corrugated aluminum or plastic air-ducts Ø150mm or Ø120mm (see item 5.3);
   – in the recirculation mode (closed circular air circulation in the kitchen), when the extractor hood is not connected to chimney, and the air is passed through aluminum grease filter (included) and smothering carbon filter and is returned to the kitchen (see paragraph 5.3).

6. Attention! Do not start extractor hood installation before connecting it to electricity network and checking its technical serviceability, and checking all of its functions.

7. We recommend that all installation works, connection, and repair of your extractor hood should be carried only by qualified specialists professionally engaged in the execution of such works.

8. The manufacturer does not bear responsibility for any damages and failures, caused by incorrect installation, operation, and repair of the extractor hood.

9. The manufacturer reserves the right to modify the product in order to improve its quality and technical specifications.

10. Technical specifications for the extractor hood are indicated in this manual and on the label attached to the inner surface of the body (access to it opens when the filter is removed).
    Attention! The extractor hood should be installed on the wall at the distance of 650-750mm above the electric cooker and at the distance 750-850 mm above the gas cooker.

MAIN TECHNICAL SPECIFICATIONS

PARTS SUPPLIED

SAFETY REQUIREMENTS

ATTENTION!
IT IS FORBIDDEN TO CONNECT THE EXTRACTOR HOOD
TO THE NETWORK OF THE ELECTRIC COOKER. PROTECT ELECTRIC CORD FROM MECHANICAL AND THERMAL DAMAGE.

While installing, the operation of conducting technical services, it is strictly forbidden to:

• connect the extractor hood to the electricity network with a voltage and frequency that does not correspond to those specified in paragraph 2;
• use lighting lamps with a power output of more than 3 watts (LED);
• carry out maintenance, replace lamps, remove filters, clean the extractor hood without removing the plug from the mains socket;
• operate the extractor hood with an open fire source, open gas burners or heating elements.Heating elements should be always covered with dishes;
• prepare food with use of alcohol;
• leave the fryer unattended;
• operate the extractor hood with removed filters;
• connect the extractor hood to the electric network of the cooker, cut the socket of the electric cord while installing.

ATTENTION! IT IS FORBIDDEN TO USE GAS (ELECTRIC) COOKER IF THE EXTRACTOR HOOD IS TURNED OFF.

1. In order to avoid damage by electric current, the extractor hood must be plugged into a grounded outlet.
2. The extractor hood connected to the separate ventilation shaft. It is forbidden to connect other appliances to the same ventilation shaft.
3. Using the extractor hood together with other heating appliances (gas, oil, ovens, etc.), besides electric, it is necessary to provide the premises, it which the extractor hood is installed with the additional flow of the fresh air (for example to open the window).
4. For air extraction to the chimney use air duct Ø150 / 120mm. A smaller diameter will create additional air resistance, which will increase noise and vibration, as well as motor overheating.
5. Provide timely cleaning of non-disposable aluminum removal filters, otherwise, the efficiency of the extraction will decrease and there will be a fire hazard due to the accumulation of grease and dust in the filter.
6. It is forbidden to turn on the extractor hood in case of ignition with the purpose of reduction of smoke until complete localization of fire.
7. In case of ignition under the extractor hood, cover the fire with a thick cloth, disconnect the extractor from the electric network, do not use water to extinguish a fire in the places where the electrical appliances are located.
8. Protect the cord for connection to the electric network from the mechanic and thermal damages.

EXTRACTOR HOOD DESCRIPTION

1. The appliance «GZ-696», «GZ-699» is an air purifying device of the exhaust type with a diameter fan (turbine), completed with a grease picking aluminum filter. It is manufactured from sheets of carbon steel with a decorative protective coating of powder paints.
2. The hood type is ” t-jak “, closing to the ventilation duct and mounted in the kitchen on the walls above the stove.
3. Depending on the installation scheme over the cooker, the extractor hood can work in two variants (see item 1.5):
   • in the mode of air extraction into the chimney of the kitchen (pic. 1).
   • in the recirculation mode (pic. 2) (closed circular air circulation in the kitchen).

Distance H:
To electric cooker 65-75cm To gas cooker 75-85cm

“It is necessary to consider, that when the extractor hood is on, the pressure is automatically lowered in the enclosed room, and should be balanced with an inflow of fresh air. This may be achieved by opening doors and windows or with use of equipment for special inflow ventilation”.

The cooker hood consists of the next components (Pic.3):

1. Fixing Brackets
2. Upper chimney
3. Lower chimney
4. Plastic pipe adapter (from Ø150 to Ø120mm)
5. Frame
6. Electro cable grounded
7. Aluminium filter
8. Lighting
9.  Control panel

EXTRACTOR HOOD INSTALLATION INSTRUCTIONS

1. Select the operation mode and place for installation of the extractor hood
2. Remove the extractor hood from the packaging.
3.  Check the work of the extractor hood, connect it to the electric network and check all its functions.
4. Make marks for the mounting holes of the body on the wall. To do this, put the paper mold with markings of 4 holes in the back wall of the body (points A, B, C, D, see the installation scheme), put the mold to the wall on the needed height indicated above, and align it on the level.
5.  Mark and drill holes in points A, B, C, D with drill Ø7mm 40mm in depth.
6. Install wall plugs into the drilled holes and install 2 trim-head screws 4,5х40 to the p. A, B, so the distance between the wall and the head of the screw is 5 mm.
7. Handle the body of the extractor hood on the screws in reference points A, B.
8. In case of necessity install pipe to pipe adaptor for air duct (Ø150/120) and install air duct (pic.4.3).
9. Install 2 trim-head screws 4,5х40 into the p. C, D, from the inside of the extractor hood.
10. Install telescopic chimney on the body of the extractor hood. Lift the upper panel of the chimney with a strap up to the ceiling so it closes the ventilation duct, and mold the grooves on the slats 2 holes for mount (p. E, F) (pic. 4.2).
11. Drill 2 holes Ø7, set wall plugs in and fix the groove with trim-head screws 4,5×40 to the wall.
12. If the extractor hood is to be operated in an air-to-chimney mode, mount the air duct of the selected diameter in accordance with the instructions, ensuring that it is tight.
13. If the extractor hood s to be operated in recirculation mode, there is no need in the air duct. Install odor carbon filter into a T-like stab of the cover of the turbo fan.
14. Set external panel of the chimney into grooves on the body of the extractor hood, and raise the internal panel up for combining of the fixing holes with the plank and join it from the side with 2 trim-head screws 2,9×9,5 (pic. 4.2).
15. Check the reliability of the mounting of the extractor hood, feed and connect the cord to the socket to the electricity.
    In order to provide additional protection against voltage fluctuations in the network, it is recommended to connect the extractor hood via an additional automatic circuit braker 6A.

EXTRACTOR HOOD OPERATION

1. Extractor hoods have 4 ventilation speeds. Depending on the volume of evaporation when cooking, you can select low, middle or high ventilation level.
2. Turn on the extractor hood in the needed mode before cooking. It is recommended to continue the work of the extractor hood for 3-5 minutes after cooking, thus the air in the kitchen will be cleared from the residues of evaporation and odors.
3. On the decorative glass of your cooker hood there is a touch switch for operating modes of the engine and lighting lamps (Pic. 5):

Switch on a cooker hood:

• press on any of the sensor speed control knobs (1, 2, 3);
• turn on lighting if necessary (button with bulb symbol).

Switch off a cooker hood:

• press the speed control knob (1, 2, 3) on the sensor, depending on the speed at which the cooker hood (1-1, 2-2, 3-3) works.
• The switching the hood on and off with the touch switch is double-pressing, that is, pressing the speed 1 – the cooker hood is switched on, press speed 1 again – the cooker hood is turned off.

Starting the timer:
To start the timer, press one of the touch buttons (1, 2, 3) and hold it for 5 seconds. The timer will automatically switch off the cooker hood in 5 minutes.

Control of cooker hood using a remote control (Fig. 6)

• Press the buttons 1, 4 or 5 to switch on the cooker hood. To switch off the hood, press the button 1.
• To increase or decrease the speed, press the button 5 or 4, respectively.
• Press the button 2 to switch the light on or off.
• To activate the timer, press the button 6 when the cooker hood is switched on.
• To switch off the timer, press the buttons 6.

MAINTENANCE INSTRUCTIONS

Attention! Before cleaning the extractor hood, disconnect it from the electricity.

• Use a damp cloth soaked in warm water with a neutral detergent for external cleaning of the painted extractor hood.

• Never use abrasive detergents, coarse sponges or detergents containing soda, acid, chlorides or solvents to clean the extractor hood.

• When cleaning, avoid getting moisture on the current-carrying parts of the extractor hood, and wipe the surfaces with a soft cloth after washing.

• The aluminum filter, holding oil and dust from the air, is clogged and should be washed after being soaked in hot water with an
  effective detergent once every 1.5 to 2 months. Changing the color of the filter after washing does not affect the quality of its work.

• To remove the aluminum filter, press the spring latch and remove the filter from the panel. Install the filter in reverse order (Pic. 7).
  Do not install the filter after washing until it is completely dry.

• The carbon filters, used during recirculation mode should be changed every 3-6 months depending on the extractor hood use. Filters are installed on the T-like stab of the cover of the turbofan by axial pushing and clockwise rotation.

• LED lamps are installed on the extractor hood for lighting the working area of the cooker. Before starting lighting lamps substitution, disconnect the extractor hood from electricity, and leave the lamps to cool. To replace the lamp, remove the aluminum filters, push the holder of the cartridge so that the lamp came out of the body of the extractor hood and remove it by turning it counterclockwise. Replace it with the new one with the same characteristics and install filters (Pic. 8).

• Picture 6. Aluminum filter removing.
• Picture 7. Replacement of the lighting lamp.
• To change the carbon filter, you need to follow the next steps (pic.9):
  • Place the carbon filter on the lock until it stops on both sides.
  • Turn the carbon filter in any direction at an angle of 90 degrees, ensuring fixation.

ELECTRICAL SCHEMATIC DIAGRAM

Possible malfunctions of the extractor hood

Read User Manual Online (PDF format)

Download This Manual (PDF format)

Download this manual  >>