Kruger Matz KM0629 Wireless Headphones Owner’s Manual

Kruger Matz KM0629 Wireless Headphones

SAFETY INSTRUCTIONS

Read this instruction manual and keep it for future reference. Producer does not take responsibility for damages caused by inappropriate handling and use of the product.

• Read the instruction manual before first use and keep it for future reference.

• Minimize the volume on your audio device before connecting the headphones in order to avoid hearing damage from sudden exposure to excessive volume. Keep the volume at a reasonable level throughout entire time of using the headphones. To prevent damage to your hearing, do not raise the volume too high.

• Do not use the headphones in places where the inability to hear ambient sound presents a serious risk (such as at railroad crossings, train stations, construction sites or on roads where vehicles and bicycles are traveling).

• Never use the headphones while driving a car, riding a motorcycle or bicycle or operating any other vehicle, as it may cause potential risk to your safety.

• Stop using the headphones if you feel a tinnitus, hearing discomfort, irritation or have other adverse reactions.

• Do not attempt to repair this device yourself. In case of damage, contact with an authorized service point for check-up/repair.

• Do not subject the headphones to strong impact.

• Clean this device with soft, slightly damp cloth. Do not use any abrasives or chemical agents to clean this product.

• Protect this product from moisture, humidity, water and any other liquid.

• Avoid using/storing it in extreme temperatures. Do not expose it to direct
  sunlight and sources of heat.

• Never use this device if it is damaged.

• Use only authorized accessories.

PRODUCT DESCRIPTION

1. MicroSD card slot
2. Microphone
3. Micro USB port
4. LED indicator
5. AUX input
6. Power button / pause
7. Volume up button / next track
8. Volume down button / previous track
9. Mode button

BLUETOOTH MODE

1. Make sure the device is tuned off. Press and hold the power button for about 3 seconds to turn the headphones on and automatically enter pairing mode (the indicator light will blink in blue and red).
2. Turn on the Bluetooth on an external device, search and connect with KM WAVE 2 device. Make sure that the headphones are close to the device they are paired with. Enter default password “0000” if necessary.
3. After proper pairing, the appropriate message will be emitted from the headphones and LED indicator will flash blue.
4. Press power button to answer the call. To dismiss press and hold the power button for about 3 seconds.

Notes:

• When connecting with the same device for the second time, just turn the headphones on, turn on the phone and enable Bluetooth function; the headphone will connect with the device automatically.
• When in Bluetooth mode, when there is an incoming call the headphones will switch to call automatically
• Operation times as well as Bluetooth range depends on various numerous factors, and may differ from the stated max. value
• If the headphones are not connected to any device, they will turn off automatically after 10 minutes of inactivity.

AUX MODE

Connect the headphones with external device to enter AUX mode. Headphones will enter AUX mode automatically. Start playing the external device.

Note:

• built-in microphone of the headphone will not work when in AUX mode
• playlist management and volume control in AUX mode are available only on the external device

FM MODE

1. Turn on the headphones and press mode button.
2. To automatically search for the nearest available FM station, press power button.
3. Press volume up or volume down button to play searched FM station.
4. Press and hold volume up or volume down button to increase or decrease volume.

MP3 MODE

1. Turn on the headphones and insert micro SD card into slot. Device will enter MP3 mode automatically.

2. Press power button to pause or play music.

3. Press and hold volume up or volume down button to increase or decrease
   volume.

4. Press volume up or volume down button to change track.

CHARGING

If the battery level is low, the LED indicator will flash red and beep every 10 seconds.
Once charging is completed, LED indicator will turn off.

SPECIFICATION

Speaker size: 40 mm
Magnet: neodymium
Voice coil: 40 mm
Frequency response: 20 Hz – 20 kHz
Impedance: 32 Ohm +/- 15%
S/N ratio: 95 dB
SPL: -10 dB
THD: 0,3%
Sensitivity: 115 ± 3dB
Nominal input power: 20 mW
Maximum input power: 30 mW
Bluetooth: 5.0 + EDR
Bluetooth range: up to 10 m
Bluetooth profiles: A2DP, AVCTP, AVRDTP, AVRCP, HFP, SPP
Built in microphone: yes
Microphone sensitivity: -38 dB ± 3 dB
Microphone S/N ratio: 58 dB
Stand-by time: up to 300 h
Playback time: up to 4 h
Talk time: up to 4 h
Battery capacity: 200 mAh
Power supply: 5 V
Ports: AUX-in (3,5 mm), micro USB (charging), micro SD
Weight: 138 g
Dimensions: 170 x 175 x 40 mm
Audio cable: 100 cm
USB cable: 60 cm
Set includes: audio cable, USB cable

LEARN MORE

For more information on this device visit: www.krugermatz.com.
Read owner’s manual carefully before using.
Visit www.krugermatz.com website for more products and accessories.
In case of any doubts or questions reach out to our Frequently Asked Questions section.

Correct Disposal of This Product
(Waste Electrical & Electronic Equipment)

(Applicable in the European Union and other European countries with separate collection systems) This marking shown on the product or its literature, indicates that it should not be disposed with other household wastes at the end of its working life. To prevent possible harm to the environment or human health from uncontrolled waste disposal, please separate this from other types of wastes and recycle it responsibly to promote the sustainable reuse of material resources. Household users should contact either the retailer where they purchased this product, or their local government office, for details of where and how they can take this item for environmentally safe recycling. Business users should contact their supplier and check the terms and conditions of the purchase contract. This product should not be mixed with other commercial wastes for disposal.

Made in China for LECHPOL ELECTRONICS Sp. z o.o. Sp.k., ul. Garwolińska 1, 08-400 Miętne.

[www.krugermatz.com](http://www.krugermatz.com)
Kruger &Matz is a registered trademark

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>