Dolphin LIBERTY 200 Robotic Pool Cleaner Instruction Manual

Robotic Pool Cleaner LIBERTY
LIBERTY 200™ | 300 User Instructions

POOL CLEANER PARTS

SPECIFICATIONS

2.1 Robot
Water temperature range: 6°C-35°C / 43°F-95°F
Water depth range: 0.4m-2.5m / 1.33ft-8.2ft
Motor protection: IP 68
Chlorine – 4 ppm, Max.
pH – 7.0-7.8
NaCl – 5000 ppm, Max.
Battery Lithium-ion | 5,000mAh | 25.2V@5Ah / 126Wh
Charger protection: IP 54
2.2 Water Conditions
Use only the robotic pool cleaner in the following water conditions:

• Chlorine: 4 ppm max.
• pH: 7.0 – 7.8
• Temperature: 6°C – 35°C / 43°F – 95°F
• NaCl: 5000 ppm max.

FEATURES AND INDICATIONS

Cycle Selector – LIBERTY 300
Use Cycle Selector to customize cleaning mode to “Floor only”:

1. Press ON to activate until the LED lights up.
2. Press ON again for 3 seconds until the purple LED blinks 3 times.
   Place the robot in the pool, and within 30 sec, it will start cleaning the pool floor.
   After cleaning cycle (90 minutes each cycle), the robot will return to default “Floor and Walls” mode.
   • You can use the Clicker for easy removal from the pool, in both “Floor and Walls” and “Floor only” mode.

Eco Mode – LIBERTY 300
Use Eco Mode to keep your pool floor clean for a week on one charge.
The robot will automaticly clean the pool floor for up to 30 min, 3 times a week, with 48 hours between cleaning cycles.

1. Press ON to activate until LED lights up.
2. Press ON again for 6 seconds until the purple LED light turns green.
   Place the robot in the pool, and within 30 sec, it will start working.

Temperature Warning
In case of temperature warning notification, place and charge the pool cleaner in a protected and shaded area, at a temperature range of 6°C – 35°C / 43°F – 95°F. Error
In case of error notification, please refer to troubleshooting.

CHARGING RECOMMENDATIONS

• When the battery is low and all indicators are off – the cleaner is on standby mode. Connect to charger to wake it up.
• Always Charge the pool cleaner in a protected and shaded area at a temperature range of 6°C – 35°C / 43°F – 95°F, until you see 3 green bars in the battery indicator panel (up to 6 hours).
• Make sure there is no object between the robot and the charger.

REMOVING THE ROBOT OUT OF THE POOL USING CLICK-UP TM (for LIBERTY 300)

1. Place the black capsule of the clicker, in the water.
2. Make sure the clicker is no more than 8 m/26 ft away from the robot.
3. Shake the clicker for at least 3 seconds.

After a few seconds the robot will climb to the waterline and will wait there for 60 seconds to be collected. Take the robot easily out of the water.

• The robot will climb the nearest wall, and will wait for 60 seconds on the waterline.
• If you can’t reach this wall, wait for the robot to move to another wall. Shake the clicker and the robot will climb to the waterline.

5.1 Removing The Robot Out Of The Pool Using Grab Hook (for LIBERTY 200)

• Standard pole
  Not included.

• After finishing its cleaning cycle, the robot will stop next to a random wall, so you will be able to pick it up with the grab-hook.

CLEANING THE FILTER BASKET

It is highly recommended to clean the filter basket after each cleaning cycle.
Note: Do not let the filter basket dry out before cleaning.
Cleaning after use – removing and cleaning the filter basketPERIODIC CLEANING – RECOMMENDED AT LEAST ONCE A MONTH

TROUBLESHOOTING

Main Symptom| Additional Symptoms| Troubleshooting Steps – Customer
---|---|---
The robot doesn’t charge| Robots Battery LEDs are Uniting in a special pattern (central LEO
• then right and left LEDs) The issue occurred while the robot was connected to the charger| 1.in case the robot feels hot to the touch charge the robot in a shaded location or when the temperature is low, for example. overnight / indoors
2.in case the robot feels cold to the touch try charging the robot in a warmer location.
The Power unit doesn’t show any LEDs at all| Try connecting the charger to a different power outlet. Make sure that the charger LED is on.
The Power Button LEO is red| 1.Try disconnecting the charger from the Power unit and connecting it back a few times.
2.Check whether an object is blocking the connection between the charger and the Power Unit
| The charging process stops, and the Power Button LED is blinking red for a short period of time| 1.Make sure that the charger is connected property
2.check whether an object is bkocking the connection between the charger and the Power unit.
Charging progress s stuck: one of the battery LEDs is banking and doesn’t synch to the steady lent after a long perod of time| 1.Check that the charger LED bins on
2.Make sure that the charger is connected properly
3.Check whether an object is blodung the connection between the charger and the Power unit
&Charge overnight in a cooler location
The battery is not lug after charging| The robot’s battery discharges while the robot s turned off| Fully charge the robot (until all battery LEDs are steady green), make sure that the robot is turned oft Do not start the cleaning process. Cl-eck the battery status after 2 days
if the battery charge level is senifxantly lower – contact Customer Care.
Red LED right appears above the power button|  | Make sure there’s nothing stuck in the tracks or brushes Clean the filter and make sure its not clogged
Disconnect and reconnect the charger 3 times.
The robot wit not start the leaning cycle. The Panel Button LED is red| The charging process works properly
The robot (wishes a 90•rnnute clearing cycle
Outing the Eco mode and Cycle Selector, the robot will amb the walls even if configured otherwise
The robot win not respond to axt,upw properly. wit start the clearing cycle instead of waiting at the wateline| Contact Customer Care: wecarePamaytronics.com
The charger is connected to the robot| Disconnect the charge: and press an the robot’s poser button to operate
The charger is dsconnected from the robot. The charging process works property| Contact Customer Care wecareemaytionxs corn

OFF-SEASON STORAGE

Before off-season or storing the robot during the winter – we recommend charging the battery at least 50% (2 green bars in the battery indicator panel).
Recommended storage temperature range: -10°C – 40°C / 14°F – 104°F.
After off-season storage, charge the robot to its fullest.

WARNINGS AND CAUTIONS

10.1 Warnings

• **** Remove the robotic pool cleaner from the pool before allowing people to enter the pool.
• When examining the robotic pool cleaner, make sure the robotic pool cleaner is switched OFF.
• Charge the battery only in the temperature range between 6°C to 35°C / 43°F to 95°F
• Keep the robotic pool cleaner out of the reach of children or persons with reduced physical, sensory, or mental capabilities, or lack of experience and knowledge, unless they have been given supervision or instruction. Cleaning and maintenance shall not be made by children.
• Use only the original battery charger.
• The battery charger must be supplied through a residual current device (RCD) having a rated residual operating current not exceeding 30mA.
• The power cord is not user-replaceable. If the power cord is damaged, stop using the battery charger and contact the service center for repair. Do not use extension cord to connect the battery charger to electric supply; provide a properly located outlet.
• DO NOT USE the robotic pool cleaner and/or its battery / power pack in case of mechanical damage to the robotic pool cleaner and/or its battery.
• To avoid the risk of fire and burns, DO NOT open, crush, heat, or burn the battery case.

10.2 Cautions
CAUTION

• **** Keep hands and fingers away from impeller motor area and driving belt mechanism to avoid injury.
• Position the battery charger at least 3.5 m / 12 ft from pool edge during operation.
• For continuous protection against possible electric shock, place the battery charger at least 11 cm / 4 in above ground.
• When lifting the robotic pool cleaner, take care to prevent back injury.
• Do not use the robotic pool cleaner if you have added liquid flocculant or any other clarifier to the pool water. These substances obstruct and damage the robot filters.
• The Lithium-Ion battery in this product is non-replaceable. It should be recycled at certified battery electronics recyclers that accept batteries. Batteries should NOT be discarded in the trash or put in municipal recycling bins. Do not disassemble the battery.

Robotic Pool Cleaner LIBERTY | User Instructions

Documents / Resources

| Dolphin LIBERTY 200 Robotic Pool Cleaner [pdf] Instruction Manual
LIBERTY 200 Robotic Pool Cleaner, LIBERTY 200, Robotic Pool Cleaner, Pool Cleaner, Cleaner
---|---
| Dolphin LIBERTY 200 Robotic Pool Cleaner [pdf] Instruction Manual
LIBERTY 200, LIBERTY 300, LIBERTY 400, LIBERTY 200 Robotic Pool Cleaner, LIBERTY 200, Robotic Pool Cleaner, Pool Cleaner, Cleaner

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>