DOLPHIN SS PRO T top Wakeboard Installation Guide
- June 4, 2024
- DOLPHIN
Table of Contents
DOLPHIN SS PRO T top Wakeboard
EXPLODED VIEW OF THE DOLPHIN SS T TOP FOR REFERENCE
STEP 1:
Unpack and check the contents of the box.
Please Read all Instrustion prior to installation
If you are NOT sure of any part of the guide or you have any questions
Please contact the DOLPHIN T Tops
PARTS LIST
ASSEMBLY INSTRUCTIONS
STEP 2: Assemble the top cover frame of your SS T T Top.
Note: The front and rear curved bars have a slight upwards curve.
The frame will pin together.
STEP 3: Assemble the cross bars of the top cover frame.
Note: The cross bar curve faces upwards as well.
Front Cross Beam: Slide 2 x tube Flat tab tub !ttings onto the bar. The Flat
tab tube fittings are used to attach your front legs to the top cross beam. At
Each end of the cross beam there is a triangular !tting.
Rear Cross Beam: The cross beam has the triangular fittings on each end of the beam..
STEP 4: Attaching the cross beams to the outer top frame.
Disconnect the curved front end of the top frame, slide on a Flat tab tub
!tting on the the straght section. (do this to both sides) Now Re attached the
curved front bar. Position the Flat Tab !ttings near the join
Attach the cross beam from side to side with curve up. Now you can repeat
process for the rear cross beam.
Note: You can move the cross beam along the side tubes and lock into a
position.
You should now have the top frame and cross beams together.
You can attach the material cover no if you wish, or do it later.
STEP 5: Assemble the brace bar between front Leg and rear Legs
Note: Front legs use the slightly curved length for it legs facing forwards.
Note: Rear legs use the large curved length for its legs facing to the rear
and outwards
You can adjust the angle of the brace bar to fit the distance between front
and rear leg.
STEP 6: Attaching the legs to your Centre Console.
Position the bottom of the front leg approx x 2 – 4 inches of the floor.
Hold the mount against the console and mark the position. Ideal to have you
legs wide apart.
Check the inside of your console for objects or wires before drilling into the
console.
When you attach the mount we recommend putting extra 12 mm ply backing to
strengthen your console to stop !ex and movment of the console. The extra
board sits between the console and the alloy backing disc we supply. Position
the 2nd mount on the leg as high as posible on your console.
The rear leg you can place higher of the floor than the front leg.
This will angle the top giving you more height at the back and head clearance.
Bottom of the legs
STEP 7: Attach the Front legs to the Top Frame cross beam.
Before you lock in the small grub screw you can rotate the legs to the
position you require.
It is recommended that you face the front leg curve forwards.
Attatch the top of the front legs to the Flat tab tube #ttings on the top
frame cross beam.
You can move the !at tab #ttings to be in the correct position along the cross
beam.
You can have the legs straight forwards or angle slightly outwards.
STEP 8: Attach the rear legs to the top frame side bar.
The rear leg curve faces backwards and angle outwards.
You rotate the legs outwards to the side bars of the top frame.
Your Flat tab tube #tting can be place on the side bars of the top frame or
outer eadge of the cross beam. You will have to determine which is the better
stable position that suit your console.
LOWRING for storage. You can remove the T Top by detaching the 8 bolts from
the mounts. OR remove all 6 bolts from the mounts leaving the bottom 2 front
leg bolts. Then pivot the T Top forwards. You can also loosen the top of the
front legs to the top cover.
WARNING : this is not simple and you are required to be careful of the
moving parts.
CARE AND MAINTENANCE
Be sure to check and tighten all fastners and connections prior to every use
Be cautious when towing or driving under obstacles, low hanging structures or
trees
Remove the material top whilst towing behind your vehicle.
Use soap and water to clean your t top. Always rinse and wipe down t top after
Contact with salt (brackish) water.
You will need to polish and maintaine the 304 Stainless it is not high grade.
You do have to maintain it.
It is recommended that you spray a clear protective coat over the grub screws
and fittings. to help protect from corrosion.
WARRANTY
Dolphin T Tops warrants the product (not including other 3rd party
accessories) against manufactures defects.
The product/part is to be sent to the Dolphin for inspection where it will
either be repaired or replaced.
(unless otherwise agreed in writing) The customer is liable for costs
associated in shipping the product/part to Dolphin T Tops.
Dolphin is not responsible for personal injury or damage to the boat caused by
the use of the t top or any transport charges or cost of installation or
removal of the t top. Dolphin is not liablity for direct or indirect or
consequential damages resulting from delay or improper installation.
Warranty does not cover anodised, polished or powder coated surfaces as well
as any hardware corrosion they are speci!cally excluded as their care and use
can not be controlled by Dolphin.
Warranty does not cover the spider coat gel cracking or damage from the
installation or use of the t top on your boat. No dealer, retailer or
manufacturer is the agent and may not assume any liablity in connection with
this warranty. This warranty is in lieu of all.
WARNING
The construction of your boats console, design, thickness of the console walls
and overall design may cause movement at the mounting points. Which will cause
“ex and movement in the T Top. If this occurs on your boat it is not a
warranty or refundable claim.
If the construction of you boats console causes movement at the mounting
points or incorrect mounting location creates added pressure on joints
increasing movement of the t top it voids warranty.
If in doubt do not install the t top.
Check all bolts and parts prior to use, especially after towing behind a
vehicle, lowering and raising after storage.
WARNING
Do not stand, climb or jump o# t top, do not tow the boat behind a vehicle
with the t top lowered.
Do Not Ski, wake,tow tubes, boats or other watercraft from the tower. Watch
out whilst moving under objects, such as bridges, low building and trees.
Dolphin T Top Canada Distributor- Seamax Marine & Outdoor
102-19155 38 Ave, Surrey, BC Canada V3Z0Y6
www.seamaxmarine.com 1877-907-7766
SUPPORT@SEAMAXMARINE.COM
Documents / Resources
|
DOLPHIN SS PRO T top
Wakeboard
[pdf] Installation Guide
SS PRO T top Wakeboard, SS PRO T top, Wakeboard, Pro T Wakeboard, T Top
Wakeboard, Top Wakeboard
---|---
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>