GDP 2010-2021 6.7l Cummins Digital Switch User Manual

GDP 2010-2021 6.7l Cummins Digital Switch

Product Information:

The 2010-2021 6.7L Cummins Digital Switch by GDP Tuning, LLC. is a product that allows you to control various features of your vehicle through a digital interface. It comes with a GDP RGB Digital Switch, a Ford Fuel Temp Sensor Plug, a Flex Lume, a USB Cable, and a Digital Switch Harness. The switch can be used to control the high-idle feature on Ford vehicles, as well as the Shift-on-the-Fly (SOTF) function on all compatible vehicles. The product is designed for use with any 12V hot wire with ignition on.

Product Usage Instructions

• Step 1: Before installing the product, make sure that the vehicle has been turned off and allowed to cool down. Wear eye protection when working on or under the vehicle.

• Step 2: Route the ORANGE SOTF switch wire through the firewall carefully, away from hot surfaces or moving parts. Secure the wire to prevent contact with sharp surfaces to avoid damage.

• Step 3: Connect the switch harness to the crankcase pressure sensor using the 3 wire plug. The ORANGE wire goes to the #3 hole of the connector which will line up with the DARK BLUE/GRAY on the vehicle side.

• Step 4: To troubleshoot your switch, you will need a voltmeter. Set your switch to position 1 and turn key to the run position (engine off or on). Test the Switch on the fly wire (Orange Wire) and ensure that the voltage readings match within their specific levels.

• Step 5: If the readings do not match, check your connections and pins to ensure they are not bent or broken.
  Also, check for debris stopping the pins from being inserted completely.

• Step 6: If the issue persists, contact the tech support line for more help: 877-223-5018.
  Caution: By installing this product onto your vehicle, you assume all risk and liability associated with its use. GDP Tuning, LLC. is not responsible for misuse of its products. By installing this product, you release GDP Tuning, LLC. of any and all liability associated with its use. Never work on a hot vehicle. Serious injury in the form of burns can result if the vehicle has been in use. Allow the vehicle to cool prior to installation.

Disclaimer

• By installing this product onto your vehicle, you assume all risk and liability asso-ciated with its use.
• GDP Tuning, LLC. is not responsible for misuse of its products. By installing this product, you release GDP Tuning, LLC. of any and all liability associated with its use.
• The purchaser and end user releases, indemnities, discharges and holds harmless GDP Tuning, LLC. from any and all claims, damages, causes of action, injuries, or expenses resulting from or relating to the use or installation of this product that is in violation of the terms and conditions on this page, the product disclaimer, and/or the product installation instructions. GDP Tuning, LLC. will not be liable for any direct, indirect, consequential, exemplary, punitive, statutory, or incidental damages or fines caused by the use or installation of this product.

Caution
Never work on a hot vehicle. Serious injury in the form of burns can result if the vehicle has been in use. Allow vehicle to cool prior to installation. Always wear eye protection when working on or under any vehicle.

OVERVIEW

• A. GDP RGB Digital Switch
• B. Ford Fuel Temp Sensor Plug
• C. Flex Lume
• D. USB Cable
• E. Digital Switch Harness

Step 1
Route the ORANGE SOTF switch wire through the firewall before connecting to the crank case sensor. Be sure to route the wire carefully, away from hot surfaces or moving parts. Secure wire to prevent contact with sharp surfaces to avoid damage.

Step 2
Use the 3 wire plug to connect the switch harness to the crankcase pressure sensor. The ORANGE wire goes to the #3 hole of the connector. This will line up with the DARK BLUE/GRAY on the vehicle side.

Troubleshooting

To troubleshoot your switch, you will need a voltmeter.

• Step 1
  Set your switch to position 1.

• Step 2
  Turn key to the run position. (engine off or on)

• Step 3
  Test the Switch on the fly wire (Orange Wire). These numbers may vary within their specific levels. (i.e. 4.0-4.9 in Position 1) The voltage you should be seeing is:

• Step 4
  If the readings do not match, please check your connections and pins to make sure they are not bent or broken. As well as, there is no debris stopping the pins from being inserted completely.

• Step 5
  If the issue persists please call our tech support line for more help. 877-223-5018

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>